A
SP-CEIL-008 DIGITAL PROJECTOR MOUNT
These are the installation instructions for your Digital Projector Mount. Included are four methods of
installation.
Select the method that works best for your viewing situation. The methods are:
NOTE: If the required height range is greater than 12½", the optional SP-LTMT-EXTP could be used to
extend the length of the suspension adapter. For further information or ordering assistance, please contact us
at the phone number and address listed at the top of this column.
The wall or ceiling where you want to install the digital projector must be capable of supporting a weight that is
five (5) times the weight of 7lbs the projector you are installing. Consult the projector’s documentation for
weight specifications. If the wall, ceiling, tabletop, shelf, or floor is not strong enough to handle five (5) times
the weight of 7lbs, then you must reinforce the installation environment. If you are unsure about the
installation environment, please consider having it reinforced and having the projector installed by qualified
personnel. Failure to do so could result in serious personal injury and damage to the projector.
To avoid personal injury, use only an approved projector mount. Using an unauthorized projector mount may
lead to poor ventilation and projector failure.
When installing the projector mount, keep in mind that the projector’s focus ring is not squarely in the center
of the front of the projector, but offset by several inches. Make sure that when you mount the projector you
offset the installation to match the amount of inches that the projector’s focus ring is offset from the center of
the front of the projector.
° Fixed Height Ceiling Installation
° Adjustable Height Ceiling Installation
(optional) SP-LTMT-EXTP-S height adjustable extension is required.
° Wall Mount Installation
(optional) SP-LTMT-EXTP-S height adjustable extension is required.
Before You Start the Installation
27700B S.W. Parkway Ave.
Wilsonville, Oregon 97070-9215
1-800-294-6400
www.infocus.com
Installation Instructions
— best for short ceilings, eight (8’) or lower
—best for high ceilings, nine (9’) feet or higher
—for installing the Digital Projector Mount on a rear wall the
R
LISTED
E176225
Copyright by InFocus Corporation
Wilsonville, OR. All rights reserved
Hardware description
The Digital Projector Mount utilizes the following hardware. Note that the letters associated with the hardware
on this list correspond to the letters listed in the instructions for each installation method.
. Four (4) 4 (mm) x 10 (mm) Phillips head screws (supplied)
B. One (1) mounting bracket (supplied)
C. Digital Projector (not included)
D. One (1) Litemount Plus® assembly (supplied)
NOTE: Hardware item (E) is what secures the Digital Projector Mount to your ceiling, wall, tabletop, floor.
Make sure you consult with your local hardware store staff for the type of hardware that works best for your
installation environment.
E. SINGLE WOOD STUD: If mounting on a single wood stud use three (3) #14 x 2" Lag bolts (minimum)
commercially available. Use the mounting points on the center of the plate as indicated in the assembly
diagram.
° SOLID STRUCTURE: If mounting to a solid structure use four (4) 5/16" x 2" Lag bolts or commercially
available hardware (depending on the installation requirements). Use the mounting points found on the outer
points of the mounting plate as indicated in the assembly diagram.
F. Allen wrench (supplied)
1
g p
(
(
g p
Tools Needed for Installing the Digital Projector Mount
A
C B
You need the following tools to install the Digital Projector Mount:
• Phillips head screwdriver (not included)
• Allen wrench (included)
• Drill (for installation environment only -
• The commercially available hardware (E) that is required by your installation environment (not included)
Mount) and drill bit to match the hardware for your installation environment (not included)
do not use a drill on the Digital Projector or the Digital Projector
Lightmount Plus® Overview
(4) Solid structure
mountin
oints
(3) Single wood stud
mountin
oints
Ceiling plate
(2) Cable access points
(2) Tension knobs
(4) Tilt tension screws
Screen side
Yellow indicator)
Lower assembly
Clamp plate
2
Safety knobs
Red indicator)
Getting the projector ready
Before you start the installation process, prepare your Digital Projector by performing the following steps
IGURE 1).
(F
1. Turn the projector (C) upside down and place it on a clean flat surface, preferably on a towel.
2. Locate the mounting bracket (B) and align it over the holes on the projector.
3. Locate the four (4) 4 (mm) x 10 (mm) Phillips head screws (A).
4. Use the Phillips head screwdriver to secure the mounting bracket (B) to the projector via the three
(3) Phillips head screws (A). Do not over-tighten the screws.
FIGURE 1
Fixed Height Ceiling Installation
Complete the following steps to install the projector mount and projector on your ceiling. This installation
works best with low ceilings (F
Note: Look at the bottom of the mount assembly (D) and locate the arrow. Make sure you install the projector
mount with the arrow pointing toward your screen.
1. Remove the upper plate from the assembly (D) secure to the ceiling structure using the commercially
available hardware (E) suitable for your environment. Be sure that the mount assembly screen indicator
arrow is pointing toward your screen.
2. Replace the mount assembly with the upper plate and fully raise the safety knob and tension knobs all
the way. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the
bottom of the mount assembly (D) by its tabs.
3. Rotate the projector (C) with the mounting bracket (B) attached 180º
is pointing toward your screen.
4. Align the safety knob on the mount assembly (D) with the end of the arrow-shaped slot on the mounting
bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the safety knob.
5. Hand-tighten the remaining two tension knobs to secure the mounting bracket (B) to the mount
assembly (D).
CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws.
IGURE 2).
so that the projector’s focus ring
FIGURE 2
E C B A
D C C B A
Ceiling structure
Wood stud
Adjustable Height Ceiling Installation
Center of wood stud
D
C
Insert and rotate 180°
and lock down
Solid ceiling structure
E
Insert and rotate 180°
and lock down
Complete the following steps to install the projector mount and projector on your ceiling with the optional
suspension adapter.
This installation works best with high ceilings (F
Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector
mount with the arrow pointing toward your screen.
6. Use the Allen wrench (F) to remove the upper plate from the mount assembly (D).
7. Use the Allen wrench to remove the two screws from the enclosed end of the of the suspension
adapter, and place it into the slotted extension on the upper plate (E). Make sure that the two (2) outer
holes on the suspension adapter align with the holes on the slotted extension on the upper plate.
8. Replace the two screws removed in step 2 into the two (2) holes to secure the suspension adapter to
the upper plate.
9. Attach the mount assembly to the suspension adapter and secure them with the two screws removed
in step 1.
10. Secure the upper assembly to the ceiling using the commercially available hardware (E) suitable for
your environment. Be sure that the upper assembly arrow is pointing toward your screen.
11. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the bottom of
the upper assembly (D) by its tabs.
12. Rotate the projector (C) with the mounting bracket (B) attached 180º
is pointing toward your screen.
13. Align the safety knob on the mount assembly with the end of the arrow-shaped slot on the mounting
bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the safety knob.
14. Hand-tighten the remaining two tension knobs to secure the mounting bracket to the amount
assembly.
CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws.
SEE FIGURE 3
NOTE: Use the Allen wrench key (F) for the following modification
IGURE 3).
so that the projector’s focus ring
3
SEE FIGURE 3 FIGURE 3
E C B A
D
B A
p
p
y
y
y
y
y
p
y
y
4
Remove
Remove
Remove
from mount
from mount
from mount
assembl
assembl
assembl
Wood stud
Ceiling plate
Remove
Remove
Remove
from mount
from mount
from mount
assembl
assembl
assembl
Ceiling plate
Ceiling structure
Adjustable screws
Center of wood stud
D
SP-LTMT-EXTP-S
extension ada
Optional
ter
C
Insert and rotate 180°
and lock down
Mount
assembl
Replace the
Replace the
Replace the
hardware
hardware
Optional
SP-LTMT-EXTP-S
extension ada
Adjustable screws
ter
hardware
Adjustable screws
Solid ceiling structure
E
Optional
SP-LTMT-EXTP-S
extension ada
ter
WARNING
When using the optional
extension adapters and making
a height adjustment while
Replace the
Replace the
Replace the
hardware
hardware
hardware
secured to the wall or ceiling do
not remove the screws
completely from the extension.
Failure to do so could result in
injury and damage to the
projector.
Insert and rotate 180°
and lock down
C
C
p
B C
Wall Mount Installation
Complete the following steps to install the projector mount and projector to your wall. (FIGURE 4)
Note: Look at the bottom of the upper assembly (D) and locate the arrow. Make sure you install the projector
mount with the arrow pointing toward your screen.
NOTE: Follow step 3 to secure the extension to the mount assembly
15. Secure the upper plate to the wall using the commercially available hardware (E) suitable for your
16. Carefully raise the projector (C) with the mounting bracket (B) attached and insert it into the bottom of
17. Rotate the projector (C) with the mounting bracket (B) attached 180º so that the projector’s focus rings
18. Align the safety knob on the mount assembly with the end of the arrow-shaped slot on the mounting
19. Hand-tighten the remaining two tension knobs to secure the mounting bracket (B) to the mount
CAUTION: Check all of the hardware for proper tightness and security. Do not over-tighten the screws.
.
environment. Be sure that the screen indicator arrow is pointing toward your screen.
the mount assembly by its tabs.
is pointing toward your screen.
bracket (B) and screw it through the opening to prevent further rotation. Hand-tighten the securing
knob.
assembly (D).
SEE FIGURE 4
NOTE: Use the Allen wrench key (F) for the following modification
Top plate
Optional
SP-LTMT-EXTP-S
extension ada
Adjustable screws
ter
Wall wood stud
Wall structure
E
B
C
WARNING
When using the optional
extension adapters and making
a height adjustment while
secured to the wall or ceiling do
not remove the screws
completely from the extension.
Failure to do so could result in
injury and damage to the
projector.
5
Loading...