InFocus SP 4800 User Manual

User’s Guide

[ English • Français • Deutsch • Español • Italiano • Norsk ]

ENGLISH

Declaration of Conformity

Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that the ScreenPlay 4800 projector conforms to the following directives and norms:

EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024

EN 61000-3-2

EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000

June, 2003

Trademarks

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Digital Light Processing is a trademark or registered
trademark of Texas Instruments. InFocus and ScreenPlay are trademarks or registered trademarks of InFocus Corporation.

FCC Warning

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

Canada

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Agency Approvals

UL, c-UL, TÜV, GOST, C-Tick

2

Table of Contents

Introduction 4
Positioning the projector 5
Connecting a computer source 6

Required computer connections 6
Optional computer connections 6

Displaying a computer source image 7

Adjusting the image 8

Using the projector with Windows 98 for the first time 9
Connecting a video device 11
Projector and Device Connector Guide 12

Computer connections 12

Video connections 12
Video device connections 15

Composite video connection 15

S-video connection 15

Component video connection 16

VGA connection 16
Displaying video 17

Adjusting the image 17
Shutting down the projector 19
Troubleshooting your setup 19
Using the remote control 27
Using the audio 28
Using the keypad buttons 28
Optimizing computer images 29
Presentation features 29
Optimizing video images 30
Customizing the projector 30
Using the menus 31

Picture menu 32

Settings menu 35
Maintenance 37

Cleaning the Lens 37

Replacing the Projection Lamp 37

Cleaning the Lamp Housing Screens 39
Using the security lock 39
Appendix 40

Specifications 40

Accessories 40

Projected image size 41

Red LED Behavior and Projector Errors 41

If you are experienced in setting up projection systems, use the Quick Setup
card that was included. For complete details on connecting and operating
the projector, refer to this User’s Guide.

Important Operating Considerations

Do not place the projector on a tablecloth or other soft coverings that may
block the front or back vents. Do not use a non-approved ceiling mount. In
the unlikely event of the bulb rupturing, thoroughly clean the area in front
of the projector and discard any edible items that may have been placed in
that area.

)

m

6

.

(

t

f

2

Do not place objects in
this area in front
of the projector

3

Introduction

Your new digital projector is easy to use and maintain. It is an exceptional
projector for both business presentations and home entertainment. The dig­ital projector is compatible with a wide variety of computers and video
devices, including:

• Most standard VCRs, DVD players (progressive and interlaced), HDTV

sources (1080i, 1035i, and 720P HDTV formats), TV and satellite tuners,
camcorders, video games, and laser disc players.

• IBM-compatible computers and laptops, up to 1024x768 resolution.

®

• Apple

lution.

The projector has native SVGA 800x600 resolution and comes with the fol­lowing standard accessories.

lens cap

power cord*

Macintosh® and PowerBook® computers up to 1024x768 reso-

projector

user’s guide and
quick setup card

e

id

u

G
’s
r

e

s

U

AV cable

computer cable

carrying
case

remote control
receiver (IR)

connector
panel

focus (thin ring)

adjustable

speaker

foot

keypad

power cord
connector

power switch

adjustable foot release

zoom (thick ring)

lamp
housing
door

security lock

S-video-to­component adapter

*country-dependent

S-video
cable

VGA-to­component
adapter

remote
control

monitor

computer

S-video

USB

audiovideo

4

Positioning the projector

To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general guide­lines:

• Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9 feet (1.49m) from the projection screen.

• Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase exten­sion cables). To ensure adequate cable access, do not place the projector
within 6 inches (.15m) of a wall or other object.

• Position the projector the desired distance from the screen. The distance
from the lens of the projector to the screen, the zoom setting, and the
video format determine the size of the projected image. The top illus­tration to the right shows three projected image sizes. For more infor­mation about image sizes at different distances, see “Projected image
size” on page 41.

• The image exits the projector at a given angle. This image offset is

132.9% when the projector is in 16:9 mode (default). This means that if
you have an image 10’ high, the bottom of the image will be 3.29’ above
the center of the lens.

• The image offset is 112.2% when the projector is in 4:3 mode. This
means that if you have an image 10’ high, the bottom of the image will
be 1.22’ above the center of the lens.

• See “Connecting a video device” on page 11 for additional information
on 16:9 and 4:3 modes.

10 ft high
image

bottom of image

3.29 ft above lens

lens center

1

2

.

5

f

t

5

3

.

3

f

t

.

4.8 ft.

Projection angle in 16:9 mode

.

f

t

.

19 ft.

7.5 ft.

5

Connecting a computer source

Required computer connections

Connect one end of the computer cable (see page 11 for connecting video
devices) to the dark blue Computer In connector on the projector. Connect
the other end to the video port on your computer. If you are using a desktop
computer, you will need to disconnect the monitor cable from the com­puter’s video port first.

Connect the black power cord to the Power connector on the side of the pro­jector and to your electrical outlet.

NOTE: Always use the power cord that shipped with the projector.

connect computer cable

connect power cable

Optional computer connections

To have sound with your presentation, connect an audio cable (not included
with this projector) to your computer and to the Audio In connector on the
projector. Visit www.infocus.com/accessories to view optional cables..

If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, connect the computer’s
monitor cable to the Monitor Out connector on the projector.

You can use your computer’s mouse with an optional remote control to
operate the navigation buttons during a presentation. The remote included
with this projector does not allow this function. Connect the projector to the
computer via a USB cable (not included). USB drivers must be installed to
use the USB feature. For more information, see page 10. Visit
www.infocus.com/accessories to view optional remote controls.

connect audio cable

connect monitor cable

connect USB cable

6

Displaying a computer source image

Remove the lens cap.

remove lens cap

Toggle t h e Power switch on the side of the projector to the On position.

The LED flashes green and the fans start to run. When the lamp comes on,
the start up screen displays and the LED is steady green. It can take a
minute for the image to achieve full brightness.

? No start up screen? Get help on page 20.

Turn on your computer.

The computer’s image should appear on the projection screen. If it doesn’t,
press the Computer button on the projector’s keypad.

If your computer has Windows 98 as its operating system, see “Using the
projector with Windows 98 for the first time” on page 9 regarding the driver
setup process.

Make sure your laptop’s external video port is active.

Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F5 is used to
turn the external display on and off. Refer to your laptop’s documentation
to learn your laptop’s key combination.

? No laptop image? Try pressing the Auto Image button on the key-
pad. Get help on page 21.

toggle Power switch

turn on computer

activate laptop’s external port

7

Adjusting the image

Adjust the height of the projector, if necessary, by pressing the release but­ton to extend the foot.

Rotate the leveling foot located at the rear of the projector, if necessary.

Avoid placing your hands near the hot exhaust vent in front of the projector.

Position the projector the desired distance from the screen at a 90 degree
angle to the screen.

See page 41 for a table listing screen sizes and distances.

adjust height

elevator
foot

adjust distance

rotate
leveling
foot

release button

Adjust the zoom or focus.

If the image is not square, adjust the keystone using the buttons on the key­pad.

Press the top Keysto ne button to reduce the upper part of the image, and
press the bottom Keys t one button to reduce the lower part.

Adjust the Contrast or Brightness in the Picture menu.

See page 32 for help with these menu adjustments.

adjust zoom or focus

adjust keystone

adjust Picture menu

8

focus
(thin ring)

zoom

(thick ring)

Using the projector with Windows 98 for the first time

The first time you connect a computer running Windows 98 to the projector,
the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wiz­ard to load the correct driver (which was installed with your Windows
operating system).

If you are running Windows 2000 or Windows ME, skip these steps and go
to “Adjusting the image” on page 8.

a Click Next to begin searching for the driver.

b Make sure “Search for the best driver” is selected, then click Next.

a

b

c Uncheck any checked boxes, then click Next. Windows automatically

locates the driver. If this driver has been removed, reload the driver using
your Windows operating system CD.

d When Windows finds the driver, you are ready to install it. Click Next.

c

d

9

Skip this page if you did not connect a USB mouse cable

For Windows 98:

• If you connected the USB cable, the Add New Hardware Wizard
appears again. Drivers must be installed to use the USB functionality.

• The Wizard launches three times.

The first time it detects a USB Composite Device.

The second time a USB Human Interface Device (for the keyboard) is
detected.

The third time it detects a USB Human Interface Device (for the
mouse).

For Windows 2000, Windows ME, and Windows XP:

• The USB drivers are automatically installed.

10

Connecting a video device

You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. There is also an audio input. You can connect the audio directly to
the projector to get sound from the built-in speaker, or you can connect the
audio to your stereo system.

Before connecting your projector, you should decide which aspect ratio you
want to use. The projector’s Aspect Ratio setting is accessed through the
projector’s Menu. See page 32 for more information.

Aspect ratio is the ratio of the image width to image height. TV screens are
usually 4:3. HDTV and most DVDs are 16:9, which is the default for this
projector. If you’re projecting onto a screen, the size/shape of the screen
may answer this question for you. If you are projecting onto a blank wall,
you don’t have the screen size restriction. What you plan to project will also
help you choose between 4:3 and 16:9. Most regular TV shows are 4:3, while
most movies are 16:9.

If a have a 16:9 screen then you should select an aspect ratio of 16:9 for
anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for anamorphic movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies
only appear correctly if the DVD player is set to output to a 16:9 television.

You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first. Exam­ples of tuners are digital cable boxes, VCRs, digital video recorders, and sat­ellite TV boxes. Basically, any device that can change channels is considered
a tuner.

4:3 screen 16:9 screen

Do Not Use

4:3
mode

16:9
mode

Native
mode
(NTSC
only)

11

Projector and Device Connector Guide

The following should help you find the connectors that you want to use to obtain the best resolution possible from your input devices, such as computers,
standard VCRs, DVD players (progressive and interlaced), HDTV sources (1080i, 1035i, and 720P HDTV formats), TV and satellite tuners, camcorders, video
games (progressive and interlaced), and laser disc players.

Computer connections

Computer connections involve attaching the computer cable included with the projector from a computer to the Computer In input. Optional connections
include attaching the AV cable from computer to projector, connecting the computer monitor to the projector, and connecting a USB cable (not-included)
from the computer to the projector to control the mouse through the remote. See page 6 for computer/projector setup information.

Video connections

The first step for connecting video is deciding what type of output connector you want to connect to the projector. If there is more than one output, select the
one with the highest quality. The best quality ranking, with 1 being the highest and 3 being the lowest, is:

1 Component video

2 S-video

3 Composite video

If you are connecting the projector to HDTV sources, the projector’s computer (VGA) connector, labeled Video In, should be used. Keep in mind that HDTV
and progressive sources should only be handled through the projector’s VGA connector. The S-video port does not function with progressive sources, even
with the Component to S-video adapter. With progressive sources, the Component to VESA adapter must be used.

projector input connectors

monitor
(out)

computer in
(HDTV and
progressive
sources)

s-video audio in
(component
sources)

video in

12

USB

Video Device

Video
Compatibility

If Your Device
Connector Is

Attach to this
Labeled Connector
on Projector

Comments For Setup Instructions, see

Standard Broadcast TV (not
HDTV) via: cable, digital
cable, satellite TV, DVD, or
VCR

Standard Video Camera

Standard Video Game

NTSC, PAL, and
SECAM formats

Component 480i

NTSC, PAL, and
SECAM formats

Component 480i

NTSC, PAL, and
SECAM formats

Component 480i

Composite video
or S-video

Component Video

Composite video
or S-video

Component Video

Composite video
or S-video

Component Video

Composite video
or S-video

S-video via the Com­ponent to S-video
adapter

Composite video
or S-video

S-video via the Com­ponent to S-video
adapter

Composite video
or S-video

S-video via the Com­ponent to S-video
adapter

Not for progressive
(i.e. HDTV) sources.
See next page.

Not for progressive
(i.e. HDTV) sources
See next page.

Not for progressive
(i.e. HDTV) sources
See next page.

Composite video connection on
page 15.
S-video connection on page 15

Component video connection on
page 16

Composite video connection on
page 15.
S-video connection on page 15

Component video connection on
page 16

Composite video connection on
page 15.
S-video connection on page 15

Component video connection on
page 16

13

Video Device

Video
Compatibility

If Your Device
Connector Is

Attach to this
Labeled Connector
on Projector

Comments For Setup Instructions, see

HDTV
(High Definition TV)

EDTV
(Enhanced Definition TV)

Progressive DVD

Progressive Video Game

1080i, 720p VGA Computer In Not for Component

480i

Component 480p Component video Computer In (via the

Component to VESA
adapter)

1080i, 720p

Component 480p

1080i, 720p

Component 480p

VGA

Component video

VGA

Component video

Computer In

Computer In (via the
Component to VESA
adapter)

Computer In

Computer In (via the
Component to VESA
adapter)

Not for Component
480i

Not for Component
480i

Not for Component
480i

VGA connection on page 16

Component video connection on
page 16

VGA connection on page 16

Component video connection on
page 16

VGA connection on page 16

Component video connection on
page 16

14

Video device connections

Composite video connection

Plug the AV cable’s yellow connector into the video-out connector on your
video device. Plug the cable’s other yellow connector into the yellow Video
In connector on the projector. Plug the AV cable’s blue connector into the
blue Audio In connector on the projector. Plug the AV cable’s white connec­tor into the left white out connector on the video device. Plug the AV cable’s
red connector into the right audio out connector on the video device.

Keep in mind that video output from composite connections are not as high
quality as S-video or component.

S-video connection

If your video device uses a round, four-prong S-video connector, plug an S­video cable into the S-video connector on your video device and into the S-
video connector on the projector. Also, plug the red and white AV cable con-
nectors into your video device’s audio out connectors ,and the blue audio
connector into your projector’s Audio In connector

Keep in mind that S-video delivers higher quality video output than com­posite, but not as high quality video output as component.

connect AV cable

connect S-video

15

Component video connection

If your video device has component connectors, use the Component to S­video adapter. For HD and progressive sources use the Component to VESA
adapter along with a Component cable (not included).

Plug the Component cable into the video device. Plug the other end of the
Component cable into one of the two adapter’s and plug the adapter into
the projector’s S-video (for S-video) or Computer in (for VESA) connector.

connect component cables via Component
to S-video adapter

or

via Component to VESA adapter

Component
to VESA

Component connection offers the highest quality video output.

VGA connection

If your video device has a 15-pin VGA output, plug one end of the com­puter cable to the VGA connector on your video source. This connector may
be labeled “To Monitor” on the video source. Plug the other end of the cable
into the Computer In connector on the projector.

For audio, connect the white and red AV cable connectors into your video
device. Plug the blue connector into the projector’s Audio In connector.

Connect the power cord to the Powe r connector on the side of the projector
and to your electrical outlet.

NOTE: Always use the power cord that shipped with the projector.

connect VGA cable and
AV cable

connect power cable

Component

to S-video

16

Displaying video

Remove the lens cap.

remove lens cap

Toggle t h e Power switch on the side of the projector to the On position.

The LED flashes green and the fans start to run. When the lamp comes on,
the start-up screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness.

? No start up screen? Get help on page 20.

Plug in and turn on your video device.

The video device’s image should appear on the projection screen. If it
doesn’t, press the Video button on the keypad.

? No image? Get help on page 21.

Adjusting the image

Adjust the height of the projector by pressing the release button to extend
the foot.

Rotate the leveling foot at the rear of the projector, if necessary.

Position the projector the desired distance from the screen at a 90 degree
angle to the screen.

See page 41 for a table listing screen sizes and distances to the screen.

toggle Power switch

turn on video device

adjust height

elevator

foot

adjust distance

release button

rotate
leveling
foot

17

Adjust the zoom and focus.

adjust zoom and focus

If the image is not square, adjust the keystone using the buttons on the key­pad. Press the top Keys tone button to reduce the upper part of the image,
and press the bottom Keystone button to reduce the lower part.

Adjust the volume on the keypad.

Adjust the Contrast, Brightness, Color, Tint, or Aspect Ratio in the Picture
menu. See page 32 for help with the menus and these adjustments.

For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
regarding Aspect Ratio, see page 11.

adjust keystone

adjust volume

adjust Picture menu options
including Aspect Ratio

focus
(thin ring)

zoom

(thick ring)

18

Shutting down the projector

Troubleshooting your setup

The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the pro­jector. The image returns when an active source is detected or a remote or
keypad button is pressed.

Power Save

The projector also has a Power Save feature that automatically turns the
lamp off after no active sources are detected and no user interaction with
the projector is performed for 20 minutes. By default, this feature is off. See
page 35.

Turning off the projector

You can turn the projector off simply by toggling the power switch to the off
position.

You can also press the remote’s Power button to place the projector in the
Off state while it is running. When the Power button is pressed twice (once
to start the power-down process and a second time to verify that you want
to power the projector off), the lamp turns off and the LED blinks green for
one (1) minute while the fans continue to run to cool the lamp. While the
LED is blinking green, the projector does not accept any keypad and remote
control input.

When the lamp has cooled, the LED lights solid green and the fans slow
down to minimal speed. To turn off the projector, toggle the power switch to
the off position.

NOTE: Once the projector has been toggled off, you must wait for one (1)
minute before turning the projector on again. This allows the lamp to prop­erly cool. However, if the remote was used to power the projector to the Off
state you do not need to wait one minute to turn it on again.

If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.

The LED on top of the projector indicates the state of the projector and can
help you troubleshoot.

Table 1: LED behavior and meaning

LED color/behavior Meaning

solid green The power switch has been toggled on

blinking green The power switch has been toggled on

blinking red

see page 41 for more information

solid red An unidentifiable error: please contact

and the software has initialized or the pro­jector has been powered off via the
remote.

and the software is initializing, or the pro­jector is powering down and the fans are
running to cool the lamp.

A fan or lamp failure has occurred. Make
sure the vents aren’t blocked (see
page 25).Turn off the projector and wait
one minute, then turn the projector on
again. If the projector has been working
for up to 4,000 hours or more (page 37),
replace the lamp and reset the lamp timer.
Contact Technical Support if the problem

.

persists

Technical Support.

The following tables show common problems. In some cases, more than one
possible solution is provided. Try the solutions in the order they are pre­sented. When the problem is solved, you can skip the additional solutions.

19

Problem Solution Result

no start up screen

only start up screen appears

A

ScreenPlay

plug power cord in projector’s left side
remove lens cap
toggle power switch

toggle power switch
on side

press the Computer button

activate laptop’s external port

restart laptop

correct image

computer image projected

A

ScreenPlay

A

20

Problem Solution Result

no computer image, just the words “Signal out of
range”

A

Signal out of

range

press the Auto Image button on keypad

adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>Adapter
(location varies by operating system)

you may also need to set a different
resolution on your computer, as shown
in the following problem, “image fuzzy
or cropped”

computer image projected

A

A

21

Problem Solution Result

image fuzzy or cropped

AA

image not centered on screen

A

set your computer’s display resolution to
the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab)
select 800x600

For a laptop,
disable laptop
monitor
or turn-on dual­display mode

move projector, adjust zoom, adjust height

adjust horizontal or
vertical position in
Picture>Advanced

menu

image clear and not cropped

A

correct image

22

Problem Solution Result

image not square adjust Keystone on keypad

image not sharp

adjust Sharpness (video sources only) in the
Picture>Advanced menu

ABAB

image does not fit 4:3 or 16:9 screen

change aspect ratio to 4:3 or 16:9 in
Picture>Aspect ratio menu

square image

correct image

AB

correct image

23

Problem Solution Result

image upside down

AB

image reversed left to right

A

projected colors don’t match source

turn off ceiling in Settings>System menu

turn off rear in Settings>System menu

adjust color, tint, color temperature,
brightness, contrast in the menus

correct image

AB

correct image

AB

correct image

COLOR

COLOR

24

Problem Solution Result

make sure vents aren’t blocked, turn off the

lamp won’t turn on, LED blinking red

projector and allow it to cool for a minute

lamp turns on

LED

“Change lamp” message appears at startup or lamp
won’t turn on and LED blinking red

LED

if lamp hours up to 4,000, lamp must be
replaced (see page 37)

check lamp hours
Main>About

replace lamp

ScreenPlay

lamp turns on

ScreenPlay

25

Still need assistance?

If you need assistance, call InFocus Customer Service directly at
1-800-799-9911. Support is free between 6 a.m. and 6 p.m. PST, Monday
through Friday. Support is available in North America after hours and
weekends for a fee at 1-888-592-6800.

Or, send us an e-mail at [e-mail].

In Europe, call InFocus in The Netherlands at [phone].

In Asia, call InFocus in Singapore at (65) 6334-9005.

This product is backed by a limited two-year warranty (page 45). An
extended warranty plan may be purchased from your dealer. When sending
your projector in for repair, we recommend shipping the unit in its original
packing material, or having a professional packaging company pack the
unit for shipping. Please insure your shipment for its full value.

Regarding this projector

When sending your projector in for repair, we recommend shipping the unit
in its original packing material, or having a professional packaging com­pany pack the unit for shipping. Please insure your shipment for its full
value.

26

Using the remote control

The remote uses two (2) provided AAA batteries. They are easily installed
by sliding the cover off the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.

To operate, point the remote at the projection screen or at the projector (not
at the video device or computer). The range of optimum operation is 0 to
30 feet (9.14m).

Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 31 for more info on the menus.

The remote also has:

• Power button to turn the projector on and off (see page 19 for shut­down info)

• backlight button to light the remote’s buttons in the dark

• Brightness and Contrast buttons to adjust the image

• Blank button to display a blank screen instead of the current image (to
change the color of the screen, see page 36)

• Source buttons to switch among sources (to assign a particular source
to a source button, see page 35) and a source toggle

• Resize button to change the Aspect Ratio (see page 32)

• Auto Image button to resynch the projector to the source

• Preset button to restore stored settings (see page 33)

• Overscan button to remove noise in a video image (page 34)

Troubleshooting the remote

• Make sure the batteries are installed in the proper orientation and are
not dead.

• Make sure you’re pointing the remote at the projector or the screen, not
at the video device or the computer, and are within the remote range of
30 feet (9.14m).

navigation buttons

backlight button

27

Using the audio

To use the projector’s speaker, connect your source to the Audio In connec­tor on the projector.

To adjust the volume, press the Volume buttons on the keypad.

Troubleshooting Audio

If you aren’t hearing the audio, check the following:

• Make sure the optional audio cable is connected.
Visit www.infocus.com\accessories to view optional cables.

• Make sure the volume is turned up enough. Press the Volume button
on the keypad.

• Make sure the correct source is active.

• Adjust the audio source.

• If playing a video, make sure the playback has not been paused.

Using the keypad buttons

Most buttons are described in detail in other sections, but here is an over­view of their functions:

Menu–opens the on-screen menus (page 31).

Select–confirms choices made in the menus (page 31).

Up/Down arrows–navigates to and adjusts settings in the menus (page 31).

Auto Image–synchs the projector to the source.

connect optional audio cable

adjust volume

menu navigation
buttons

Presets–cycles through the available preset settings (page 33).

Key ston e–adjusts squareness of the image (page 8).

Vo lu me –adjusts sound (page 28).

Video and Computer–changes the active source.

28

Optimizing computer images

After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For gen­eral information on using the menus, see page 31.

• Adjust the Keystone, Contrast, or Brightness in the Picture menu
(page 32).

• Change the Aspect Ratio. Choose the option that best fits your input
source (page 32).

• Adjust the Color Temperature in the Advanced menu (page 34).

• Adjust the phase, Tracking, or Horizontal or Vertical position in the
Advanced menu (page 34).

• Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later (page 33).

Presentation features

Several features are provided to make giving presentations easier. Here is an
overview, details are found in the menu section.

• The Blank button on the remote allows you to display a blank screen
instead of the active source. You can determine the color of this screen
(page 36).

• The Startup Logo option lets you change the default start up screen to a
blank or default screen (page 36).

• Power Save is provided to automatically shut down the projector after
several minutes of inactivity. This helps preserve lamp life (page 35).

29

Optimizing video images

Customizing the projector

After your video device is connected properly and the image is on the
screen, you can optimize the image using the onscreen menus. For general
information on using the menus, see page 31.

• Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu (page 32).

• Change the Aspect Ratio. Choose the option that best fits your input
source (page 32).

• Select a Sharpness setting (page 34).

• Use the Color Control to adjust the color gain (page 34).

• Adjust the Color Temperature. Select a listed warmth value (page 34).

• Turn on Overscan to remove noise on the edges of the image.

You can customize the projector for your specific setup and needs. See
page 35 to page 37 for details on these features.

• For rear projection, turn rear mode on in the Settings>System menu.

• For ceiling mounted projection, turn ceiling mode on in the Set-
tings>System menu.

• Specify which source the projector checks first for active video during
power-up.

• Turn the projector’s display messages on and off.

• Turn on power saving features.

• Specify blank screen colors and start up logos.

• Specify the language viewed on the menus.

• Save settings for the active source as a preset.

30

Using the menus

To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to high­light the desired submenu, then press the Select button.

To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio but­tons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to and press Previous to go to the pre­ceeding menu; press the Menu button at any time to close the menus.

Dots appears before the menu name. The number of dots indicate menu’s
level, ranging from one (the Main menu) to four (the most nested menus).

The menus are grouped by usage:

• The Picture menu provides image adjustments.

• The Settings menu provides set-up type adjustments that are not
changed often.

• The About menu provides a read-only display of information about the
projector and source.

Certain menu items may not be visible or may be grayed depending upon a
particular source being connected. For example, Sharpness is only available
for video sources and is not visible when a computer source is active. Menu
options are grayed out only if the source if selected but no signal is present.
For example, if the projector is set to a video source but the source, such as a
DVD player, is turned off video menu options are grayed out.

Main menu

Picture
menu

dots

keypad navigation
buttons

Settings
menu

About menu

31

Picture menu

To adjust the following settings, highlight the setting, press Select, use the
up and down arrows to adjust the values, then press Select to confirm the
changes.

Key ston e: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.

Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.

Brightness: changes the intensity of the image.

Color: adjusts a video image from black and white to fully saturated color.

The color setting applies to video sources only.

Tint: adjusts the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.

Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 4:3. HDTV and most DVDs are 16:9. The default is
16:9.

Select Native to see the unmodified input with no resizing by the projector.
Select 16:9 to watch enhanced widescreen DVDs.

For more information regarding Aspect Ratio, see page 11.

Picture menu

increasing keystone

decreasing keystone

Aspect ratio

32

Presets: Presets present you with intensity configurations optimized for the

input source. You can select a preset configuration that has been specifically
tuned for either Presentation, Photography, Film, and Video (Film input is
material originally captured on a film camera, like a movie; video input is
material originally captured on a video camera, like a TV show or sporting
event.) Your viewing preferences may vary. Cycle through the preset inten­sity configurations and pick the one you like the best.

Presets are user-definable. You can use the preset as a starting point, then
further customize the settings for each source. The settings you customize
are saved in the preset for each source. To restore the factory default set­tings, choose Factory Reset in the Settings>Service menu (page 36).

To set a preset for the current source, adjust the image, select Save User in
the Presets menu, then select Yes. You can recall these settings in the future
by selecting the User 1 preset.

Save Settings

Presets

33

Advanced menu

Sharpness: (video sources only) changes the clarity of the edges of a video

image. Select a sharpness setting.

Color Temperature: changes the intensity of the colors. Select a listed rela­tive warmth value.

Color Control: allows you to individually adjust the gain for the red, green,
and blue colors.

Video Standard: when it is set to Auto, the projector attempts to automati­cally pick the video standard based on the input signal it receives. (The
video standard options may vary depending on your region of the world.) If
the projector is unable to detect the correct standard, the colors may not
look right or the image may appear “torn.” If this happens, manually select
a video standard by selecting NTSC, PAL, or SECAM from the Video Stan­dard menu.

Overscan: (video sources only) removes noise around the video image.

Advanced menu

Sharpness

Color Temperature

Sync Threshhold Adjust: If a hardware device, such as a DVD player, is
not syncing properly with the projector, select this option to help it to sync
when connected to the projector.

The following four (4) options are for computer sources only.

Phase: adjusts the horizontal phase of a computer source.

Tr a c k i ng : adjusts the vertical scan of a computer source.

Horizontal/Vertical Position: adjusts the position of a computer source.

Color Control

Video Standard

34

Settings menu

Audio: allows adjustments to Volume of the internal speaker. Adjustments

can also be made from the projector’s keypad.

Sources: when the Auto Source feature is on, the Source Enable feature
indicates which sources the projector attempts to lock onto.You can use the
Source Enable feature to eliminate certain sources from this search, which
will speed the search. By default, the check boxes for all sources are
checked. Uncheck a source’s box to eliminate it from the search.

System: Rear reverses the image so you can project from behind a translu­cent screen. Ceiling turns the image upside down for ceiling-mounted pro­jection. Display Messages displays status messages (such as “Searching” or
“Mute”) in the lower-left corner of the screen. NND prevents your notebook
computer from going into Screen Save mode if the USB cable is connected.
Power Sav e automatically turns the lamp off after no signals are detected
for 20 minutes. After an additional 10 minutes with no signal, the projector
powers down and can be toggled off. If an active signal is received before
the projector powers down, the image will be displayed.

Settings menu

Audio

Sources

Source
Enable

System

35

Startup Logo: allows you to display a blank screen instead of the default

screen at startup, and when no source is detected.

Blank Screen: determines what color is displayed when you press the
Blank button on the remote.

Startup Logo

Blank Screen

Language: allows you to select a language for the onscreen display.

Service: To use these features, highlight them and press Select.

Factory Reset: restores all settings to their default.

Service Code: only used by authorized service personnel.

About: provides information about the projector and the active source.

Showing the About box is the default action assigned to the Effect button.

Language menu

Service menu

About menu

36

Maintenance

Cleaning the Lens

1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

• Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.

2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you

don’t intend to use the projector immediately, replace the lens cap.

Replacing the Projection Lamp

The lamp hours used timer in the About menu counts the number of hours
the lamp has been in use. After approximately 3,980 hours, the message
“Change lamp” appears on the screen at startup. If the maximum lamp time
of up to 4,000 hours is exceeded, the lamp will not light. In this case, after
replacing the lamp you must reset the lamp hours by simultaneously press­ing both Volu me buttons on the projector’s keypad and holding them for 10
seconds.

NOTE: You can order new lamp housings from your dealer. See “Accesso­ries” on page 40 for information. Use only a replacement lamp with the
same type and rating as the original lamp.

1 Turn off the projector and unplug the power cord.

Lamp hours used

wait 30 minutes

2 Wait 30 minutes to allow the projector to cool thoroughly.

3 Turn the projector on its side so that the lamp door is facing you. Using a

flat-blade screwdriver, gently pry the lamp door from the projector by
placing the screwdriver blade into the space between the top of the lamp
door and the projector.

lamp door

37

4

l

Loosen the two captive screws that attach the lamp housing to the pro­jector.

5 Detach the lamp connector from the projector by depressing the locking

tab on the connector and lightly pulling it free.

WARNING:

To avoid burns, allow the projector to cool for at least 30 minutes
before you replace the lamp.

amp

connector

lamp cable

Do not drop the lamp housing or touch the glass bulb! The glass
may shatter and cause injury.

Be extremely careful when removing the lamp housing. In the
unlikely event that the bulb ruptures, small glass fragments may be
generated. The lamp housing is designed to contain these frag­ments, but use caution when removing the lamp housing.

6 Carefully remove the lamp housing. Dispose of the lamp in an environ-

mentally proper manner.

7 Install the new lamp housing and tighten the screws.

8 Re-attach the lamp connector to the projector. The locking tab should

engage when the connector is fully plugged in.

9 Replace the lamp door.

10 Plug in the power cord and toggle the Powe r switch to turn the projector

back on.

38

screw

connector

locking tab

lamp
housing

lamp
housing

lamp cable

screw

Cleaning the Lamp Housing Screens

In dirty or dusty environments, the two dust filter screens in the lamp hous­ing can become clogged, causing high temperatures and premature lamp
failure. Routine maintenance to remove dust from the screens lowers the
lamp operating temperature and prolongs lamp life. To maximize lamp life
you should clean the screen every 250 hours.

1 Remove the lamp housing.

2 Examine the dust filter screens on the lamp housing. If necessary, use a

vacuum cleaner set on low power to clean the screens. Be careful not to
disturb any internal components when cleaning the screens.

3 Replace the lamp housing and lamp door.

Using the security lock

The projector has a security lock for use with a PC Guardian Cable Lock
System. If you have a PC Guardian Cable Lock System, refer to the informa­tion that came with the lock for instructions on how to use it.

lamp housing

lamp

two screens
(one on each
side of the
lamp housing)

security
lock

39

Appendix

Accessories

Specifications

Te m p e r a t u r e

Operating

Non-operating

Altitude Operating 0 to 10,000 feet (3,048 meters)

Non-operating 0 to 20,000 feet (6,096 meters)

Humidity Operating 10% to 95% relative humidity, non-condensing
Non-operating 10% to 90% relative humidity, non-condensing

Dimensions

We ig ht

Optics Focus Range

Lamp type

Input Power Requirements 100-120/200-240 3/2A 50/60Hz

50 to 104
50 to 95

-4 to 140

12.5 x 9.8 x 4.49” (318 x 249 x 114 mm)

6.8 lbs. (3.1 kg) unpacked

4.9 - 32.8 feet (1.5 - 10 m)

150 - W DC SHP lamp

° F (10 to 40° C) at sea level

° F (10 to 35° C) at 10,000 feet

° F (-20 to 60° C)

Standard Accessories
(ship with the projector)

Shipping Box (with packaging) 110-0731-xx

Soft Carrying Case 110-0580-xx

Computer Cable 6 ft (1.8 m) 210-0175-01

S-video to Component Adapter 210-0206-xx

VGA to Component Adapter 210-0261-xx

AV Cable 301379B

S-video Cable 210-0125-10

Power Cable (country-dependent) 210-0023-xx

Remote and Batteries 590-0567-xx

Projection Lamp Housing
(included in projector)

Lens Cap 505-1523-xx

Quick Setup Card 009-0821-xx

User’s Guide 010-0474-xx

Safety Card 009-0659-xx

Color-coded Cable Ties, 3 set SP-CABLETIES

NOTE: Use only approved accessories.

Part Number

SP-LAMP-009

40

Projected image size Red LED Behavior and Projector Errors

If the projector is not functioning properly and the LED is blinking red, con-

Tabl e 2:

Range of distance to the screen for a given screen size for the projector

Distance to screen

Diagonal
Screen Size
(inches/m)

40/1 32/0.8 5.8/1.8 4.8/1.5

50/1.3 40/1 7.8/2.4 6,5/2.0

60/1.5 48/1.2 8.8/2.7 7.5/2.3
100/2.5 80/2 14.6/4.5 12.4/3.8

150/3.8 120/3.1 22.6/6.9 19.03/5.8
200/5.1 160/4.1 30.5/9.3 25.2/7.7

Image Width
(inches/m)

Maximum
distance
(feet/m)

Minimum
Distance
(feet/m)

sult Ta b l e 3 to determine a possible cause. There are two-second pauses
between the blinking cycles.

Table 3:

Red LED Behavior Explanation

One (1) blink The lamp won't strike after five (5)

attempts. Check the lamp and lamp door
installations for loose connections.

Two (2) blinks The lamp counter hours have exceeded

lamp life hours. Replace the lamp and
reset the lamp hours counter.

Three (3) blinks The projector has shut down. Check to

see if the lamp door is open. If the lamp
door is closed, toggle off the projector
and wait one minute, then toggle the pro­jector on again. If the lamp does not strike
after one minute, replace the lamp.

Four (4) blinks The fan has failed.

Five (5) blinks The projector is overheating. Check for a

blocked air vent.

41

Numerics

16x9 vs 4x3 screen aspect 11
800x600 resolution 4

A

About 36
Accessories

standard 40
accessories, ordering 40
Advance menu 34
altitude limits 40
Aspect ratio 32
aspect ratio 11
Audio 35
Audio In connector 6, 15, 28

B

Blank button 29
Blank Screen 36
blinking green 19
blinking red 19
Brightness 32

C

cable box 11
cables

ordering 40
Ceiling 35
Color 32
Color Control 34
Color Space 34
Color Temperature 34
compatibility

IBM-compatible 4

Macintosh 4

video devices 4
component cable connector 16
Computer In connector 6
connecting

video device 11
connectors on projector 13, 14
Contrast 32
Customer Service 26
customizing the projector 30

D

Display Messages 35
Drivers

USB 10

Windows 98 10
DVDs 32

E

e-mail

techical support 26

F

Factory Reset 36
focus 8, 18

H

HDTV 4, 12, 32
Horizontal 34

I

IBM-compatible computers 4
image

size 5
image optimization 29
image size

projected 41

K

keypad buttons

projector 28
keystone adjustment 8, 18

L

lamp

ordering 40
Lamp Housing Screens

cleaning 39

42

lamp replacement 37
Language 36
LED 19

blinking green 19
solid green 19

LED Behavior

red 41
LED behavior 19
lens

cap 40
leveling foot 17

M

Macintosh computers

compatibility 4
maintaining the projector 37
Menu button 31
menu usage 31
Monitor Out connector 6
mouse, using your 6

N

NND 35

O

optimizing images 29
optimizing video 30
Overscan 34

P

Phase 34
phone numbers

technical support 26
Picture menu 32
Power connector 6
power cord 6, 16
Power Save 19
Power switch 7
presentation

features 29

Presets 33
projection distance 5
projector

connecting video devices 11
customization 30
keypad buttons 28
maintenance 37
positioning 5
returning for service 26
setting up 5
troubleshooting problems 19
turning off 19
warranty 26

R

Rear 35
Red LED behavior 41
replacing the lamp 37

S

Screen Aspect 11
security lock 39
Service 36
Service Code 36
Settings menu 35
sharpness 34
solid green 19
solid red 19
Specifications 40
Startup Logo 36
S-video connector 15
System 35

T

technical support

e-mail 26

phone numbers 26
temperature limits 40
Tint 32

43

Tracking 34
troubleshooting 19
turning off

projector 19

TV tuner 11

U

USB 6
USB, using your mouse 6

V

vents 3
Vertical 34
Video In connector 15
video optimizing 30
Video Standard 34
volume adjustment 18
Volume button 28

W

Windows 2000 10
Windows 98 9
Windows ME 10
Windows XP 10

Z

zoom 8, 18

44

Limited Warranty

Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Cor­poration (“InFocus”) warrants that the Projector, Lamps and Accessories
(hereinafter collectively or individually referred to as “Product” as appro­priate) purchased from InFocus, an InFocus distributor, or an InFocus
reseller will conform to InFocus’ specifications and be free from defects in
material or workmanship for the respective Limited Warranty period pro­vided below. InFocus does not warrant that the Product will meet the spe­cific requirements of the end-user customer.

If the Product while subject to this Limited Warranty, is defective in material
or workmanship during the warranty period, then InFocus, at its option
will REPAIR or REPLACE the Product.

All exchanged parts and Products replaced under this Limited Warranty
will become property of InFocus. InFocus’ sole obligation
pay for) all labor necessary to repair the Product found to be defective
within the Limited Warranty period and to repair or replace defective parts
with new parts or, at the option of InFocus
equivalent or superior to new parts performance. Limited Warranty periods
are as follows:

• Projector Product Limited Warranty Period (Excluding Lamps)
Two (2) years from date of purchase.

• Lamp Product Limited Warranty Periods
Product purchase, the original installed lamp shall have a 90-day or
500 hours usage Limited Warranty Period, whichever comes first, and
replacement Lamps purchased at the time of Projector Product pur­chase will have a 500 hours usage Limited Warranty period.

• Accessory Product Limited Warranty Period
of purchase.

WARRANTY LIMITATION AND EXCLUSION

THIS WARRANTY SETS FORTH INFOCUS’ MAXIMUM LIABILITY FOR
ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS PUR­CHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER.
InFocus shall have no further obligation under the foregoing Limited War-

, serviceable used parts that are

: From the date of Projector

is to supply (or

: one (1) year from date

,

:

ranty if the Product has been damaged due to abuse, misuse, neglect, smoke
exposure (cigarette or otherwise), accident, unusual physical or electrical
stress, unauthorized modifications (including use of an unauthorized
mount), tampering, alterations, or service other than by InFocus or its
authorized agents, causes other than from ordinary use or failure to prop­erly use the Product in the application for which said Product was intended.

This Limited Warranty excludes Product cleaning, repair, or replacement of
plastics due to cosmetic damage and damage as a result of normal wear.
Product repair outside of the terms of the Limited Warranty will be on a
time and materials basis. Prolonged Product “demonstration” causes
unusual Product wear and is not considered normal use under the terms of
this Limited Warranty.

The Accessory Product Limited Warranty covers the accessory item only
and excludes normal wear. The Lamp Product Limited Warranty excludes
expected lamp degradation.

Remanufactured Products and Software Products are exempt from the fore­going Limited Warranty. Please refer to the appropriate Remanufactured
Product Limited Warranty or Software Product Limited Warranty for appli­cable Warranty information.

DISCLAIMER OF UNSTATED WARRANTIES

THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLI­CABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR­RANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR
PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND
THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED
OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS.
SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS
MAY NOT APPLY TO YOU.

45

Limited Warranty Period

The Limited Warranty periods hereof commence on the date of purchase by
the end-user customer. These Limited Warranty provisions shall apply only
to the end-user purchaser (first person or entity that purchased a new Prod­uct for personal or business use and not for the purpose of distribution or
resale). SOME JURISDICTIONS MAY GRANT YOU CONSUMER RIGHTS
WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE
DURATIONS PROVIDED HEREIN, AND INFOCUS WILL HONOR ALL
SUCH CONSUMER RIGHTS.

To Be Eligible For Limited Warranty Coverage

Any person exercising a claim under this Limited Warranty must establish
to the satisfaction of InFocus both the date of purchase and that the Product
was purchased new. The sales receipt or invoice, showing the date of pur­chase of the Product is the proof of the date of purchase.

To Obtain Warranty Service

During the Limited Warranty period, to exercise this Limited Warranty, the
purchaser must first contact 1) InFocus, 2) a service facility authorized by
InFocus or 3) the place of original purchase.

InFocus Customer Service – 1-800-799-9911 or [e-mail]

For Warranty service, the purchaser will be advised to return or deliver the
defective Product freight and all fees prepaid, to an InFocus Service Center
or to a service facility authorized by InFocus. When returning Product to
InFocus, a Return Material Authorization Number (RMA ); is required and
must be clearly displayed on the outside of the shipping carton or a similar
package affording an equal degree of protection. InFocus or the service
facility authorized by InFocus will return the repaired/replaced Product
freight prepaid to the purchaser.

Products returned for Warranty service must be accompanied by a written
letter that: (i) explains the problem; (ii) provides proof of date of purchase;
(II) provides the dealer’s name; and (I) provides the model and serial num­ber of the Product.

Upon request of InFocus Corporation or an authorized repair center for
InFocus, proof of legal import must accompany the warranty repair Prod­uct, otherwise the Product must be returned to the place of original pur­chase, to the manufacturer (Purchaser must bear all tax, duty and freight),
or the Purchaser must bear charges for the warranty repair.

No repair or replacement of Product or part thereof shall extend the Limited
Warranty period as to the entire Product. Warranty on the repair part and
workmanship shall only be effective for a period of ninety (90) days follow­ing the repair or replacement of that part or the remaining period of the
Product Limited Warranty whichever is greater.

LIMITATION OF LIABILITY

IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY
WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN
NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF
THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND
UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPE­CIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR
LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE
STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING
INFOCUS’ LIABILITY.

Limitation on Bringing Action

- No action, regardless of form, arising out
of the agreement to purchase the Product may be brought by purchaser
more than one year after the cause of action has accrued.

Governing Law

- Any action, regardless of form, arising out of the agree-

ment to purchase the Product is governed by Oregon law.

Mandatory Arbitration

– Any action, regardless of form, arising out of the

agreement to purchase the Product is subject to mandatory arbitration.

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION
OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS,
DEPENDING ON JURISDICTION.

46

InFocus Corporation
In the Americas:

27700B SW Parkway Avenue
Wilsonville, Oregon 97070-9215
1-800-294-6400 •503-685-8888
Fax: [phone]
http://www.infocus.com

In Europe:

InFocus International B.V.
Strawinskylaan 585
1077 XX Amsterdam
The Netherlands
Phone: [phone]
Fax: [phone]

In Asia:

238A Thomson Road
#18-01/04 Novena Square
Singapore 307684
Telephone: [phone]
Fax: [phone]