Interactive Transmitter
English . Español . Français . Deutsche
Model:
INA-SIMTTM1
1
www.infocus.com/SimpleShare
1
2
English
Status LED
1
Connect micro USB plug of charging cable to micro USB port of the Transmitter.
2
Connect USB plug of charging cable to an adapter or USB port on source device.
3
Wile Transmitter is being charged, the status LED will glow Red. The Red status LED will
* Charging time will vary depending on the level of the charging current. If battery is empty,
it will take ~2.5 hours for a full charge with an adapter of 5V/2A.
3
B.
A. HDMI : Connect to HDMI output port of source device
C. Micro-USB Port : Power input for micro USB plug of charging cable
D.
Transmit Button
a. Start/End Transmission
b. Switch device if using multi-transmitters
E. Status LED
Mode
Live
Mode
Setting
Mode
LED Color
No Light
PURPLES olid
BLUE
ORANGE
RED
PURPLE
BLUE
RED
Status Description
No power
System booting
Ready to transmit
Solid
Video streaming
Blinking
Low battery warning
Solid
(20% of battery remaining)
HDMI pairing error
Solid
Charging
Solid
Pairing
Solid
Blinking
Pairing success
Blinking
Waiting to re-boot
F. T ouch USB Dongle: Connect to USB port of source device
4
A.
D.
C.
E.
1
Remove Touch USB Dongle from the Transmitter
2
Insert Touch USB Dongle into the USB IN port of laptop or PC
3
Plug SimpleShare Transmitter into the HDMI out port of laptop or PC. Use HDMI extension cable
provided if necessary.
4
Slide the power switch to the left to turn power ON. Status LED will light blue
5
Click Transmit button and an image will appear on the display device of which the
Receiver is installed.
If multiple Transmitters are connected, the corresponding screen of the Transmitter that has
just been clicked will appear, as part of the product’s integrated switching function
of the Receiver, or on www.infocus.com/SimpleShare
5
Notice
The screen in part may not transfer if the aspect ratio of source device does not match with
that of the display device.
Maximum range for wireless application may vary depending on the environment.
The wireless device in use may be subjected to radio interference during operation.
Turn power OFF when not in use.
This device comply with part15 of FCC rules. (FCC Part 15.19(a)
Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device & its accessories must accept any interference received, including interference
that may cause undesired operation.
Class B digital device or peripheral (FCC Part 15.105)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
6
Caution (FCC Part 15.21) : Any changes or modications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure
Your wireless device is a low power radio transmitter and receiver.
When it is on, it receives and also sends out radio frequency (RF) signals.
In August, 1996, the Federal Communications Commissions (FCC) adopted RF exposure
guidelines with safety levels for wireless device. Those guidelines are consistent with the
safety standards previously set by both U.S. and international standards bodies:
ANSI C95.1 (1992) *
NCRP Report 86 (1986)
ICNIRP (1996)
Those standards were based on comprehensive and periodic evaluations of the relevant
scientic literature.
For example, over 120 scientists, engineers, and physicians from universities, government
health agencies, and industry reviewed the available body of research to develop the ANSI
Standard (C95.1).
* American National Standards Institute; National Council on Radiation Protection and
Measurements ; International Commission on Non-Ionizing Radiation Protection.
The design of your device complies with the FCC guidelines (and those standards).
This equipment should be installed and operated with minimum 20 cm between the radiator
and your body.
7
Español
Modelos:
INA-SIMTTM1
8
www.infocus.com/SimpleShare
8
Apariencia del Producto
Español
Puerto Micro-USB
Modem USB Táctil
LED Indicador
de estado
Botón de Transmisión
Interruptor de Corriente
Conector HDMI
9
Loading...