InFocus IN3902LB, IN3904LB User Manual
IN3902LB, IN3904LB
010-0728-02
Regulatory models: W3902, W3904
Declaration of Conformity
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Portland, OR
97223-8368, USA
We declare under our sole responsibility that
following directives and norms:
EMC Directive 2004/108/EC
R&TTE Directive: 1999/5/EC
EuP Directive: 2005/32/EC
Low Voltage Directive: 2006/95/EC
ETSI: EN 300 440, EN 301 489
EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3
Safety: IEC 60950-1:2005, MOD.
The receiver portion of this product is a Category III device, as specified in EN 300
440.
this projector conforms to the
Trademarks
DisplayLink is a trademark of DisplayLink Corporation.
Apple, Macintosh, and PowerBook are trademarks o
of Apple Computer, Inc. IBM is a trademark or registered trademark of
International Business Machines, Inc. Microsoft, PowerPoint, and Windows
are trademarks or registered trademarks of Microsoft Corporation. Adobe
and Acrobat are trademarks or registered trademarks of Adobe Systems
Incorporated. DLP® and the DLP logo are registered trademarks of Texas
Instruments and BrilliantColor™ is a trademark of Texas Instruments.
InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks
or trademarks of InFocus Corporation in the United States and other
countries.
NOTE: This product
equipment under the European Union's Waste from Electrical
ctronic Equipment ("WEEE") Directive (2002/96/EC).
and Ele
The WEEE Directive requires that covered equipment be
collected and managed separately from typical household waste
in all EU member states. Please follow the guidance of your local
environmental authority or ask the shop where you purchased
the product for collection or recycling options.
is covered electrical and electronic
r registered trademarks
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on
which the receiver is connected.
--Consult the dealer or an experienc
Changes or modifications not expressly approved by InFocus Corporation
void authority to operate the equipment.
may
a circuit different from that to
ed radio/TV technician for help.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Agency Approvals
UL, cUL
Other specific Country Approvals may apply.
certification label.
This document applies to regulatory models W3902 and W3904.
Input ratings: 100-240Vac, 3.3-1
InFocus reserves the right to alt
any time without notice.
.2A, 50-60Hz
er product offerings and specifications at
Please see product
1
Table of Contents
Introduction 4
Positioning the projector 6
Connecting a computer source 7
DisplayLink or VGA 7
Optional computer connections 8
Displaying an image 9
Adjusting the image 10
Connecting a video device 12
Video device connections 12
Composite video connection 12
HDMI 1.3 connection 12
S-video connection 12
VGA connection 12
Component video connection 12
LiteBoard™ Wand 13
Charging the Wand’s Battery 13
Wand Position and Avoiding Shadows 14
Using More than One Wand 14
Wand Features 14
Buttons and Wand Tip 15
LiteBoard Wand Menu 15
Troubleshooting LiteBoard 16
Shutting down the projector 18
Troubleshooting your setup 18
Using the remote control 26
Using the audio 27
Using the keypad buttons 28
Optimizing computer images 29
Presentation features 29
Optimizing video images 30
Customizing the projector 30
Dynamic Messaging 30
Using the menus 31
Basic Picture menu 32
Advanced Picture menu 33
Setup menu 34
Status and Service menu 37
Using Network Functions 38
Using LitePort 42
Maintenance 45
Cleaning the lens 45
Replacing the projection lamp 46
Using the security lock 47
2
Important Operating Considerations for Safety
5
’ /1.5m
8
’
/2.4m
3
’
/1m
2
’
/0.6m
• Refer to this guide for proper startup and shutdown procedures.
• Follow all warnings and cautions in this manual and on the projector.
• Place the projector in a horizontal position no greater than 15 degrees
of
f axis.
• Locate the projector at least 4' (1.2m) away
vents.
• Do not block ventilation openings. Locate the projector in a well-
ventilated area without obstructions to intake or exhaust vents. Do not
place the projector on a tablecloth or other soft covering that may block
the vents.
• Do not place the projector in direct sunlight, humid, greasy or dusty
places or in places where the projector may come into contact with
smoke or steam.
• Do not look directly into the lens while the projector is being used.
• Do not drop the projector.
• Do not spill liquid on the projector. Spilled liquid may damage the
projector.
• Use the power cord provided. Connect
with a protective safety (earth) ground terminal. A surge-protected
power strip is recommended.
• Do not overload wall outlets.
• When disconnecting the power cord, hold
• Wash hands after handling the cables supplied with this product.
• The projector remote control uses batteries. Make sure the batteries’
polarity (+/-) is
aligned correctly. Dispose of used batteries in
accordance with local disposal laws.
• Use an InFocus approved ceiling mount kit for proper fitting,
ventilation and installation. The warranty does not cover any damage
caused by use of non-approved ceiling mount kits or by installing in an
improper location.
• When the projector is ceiling mounted, wear protective eyewear to
prevent eye injury before opening lamp door.
from any heating or cooling
the power cord to a receptacle
the plug, not the cord.
• Refer all service to qualified service personnel. Servicing your own
projector can be dangerous to you and will void the warranty.
• Only use replacement parts specified by InFocus. Unauthorized
substitutions may result in fire, electrical shock, or injury, and may
void the warranty
• Only genuine InFocus lamps are tested for use in this projector. Use of
non InFocus lamps may cause electrical shock and fire, and may void
the projector warranty.
• Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
• The projector uses a high-pressure mercury glass lamp. The lamp may
fail prematurely, or it may rupture with a popping sound if jolted,
scratched, or handled while hot. The risk of lamp failure or rupture
also increases as the lamp age increases; please replace the lamp when
you see the “Replace Lamp” message.
• In the unlikely event of a lamp rupture, particles may exit through the
projector
vents. Keep people, food, and drinks out of the "keep out"
area under and around the projector, as indicated by the "X" areas
below.
Follow these instructions to help ensure image quality and lamp life over
life of the projector. Failure to follow these instructions may affect the
the
warranty. For complete details of the warranty, see the Warranty Booklet.
3
Introduction
zoom (rear ring)
focus (front ring)
touch keypad
elevator foot
lens
remote control
receiver (IR)
leveling foot
connector
panel
remote control
receiver (IR)
power cord
connector
Your new digital projector is simple to connect, easy to use, and
straightforward to maintain. It is a versatile projector that is flexible enough
for business presentations and home video viewing too. The IN3902LB has
native XGA 1024x768 resolution, and the IN3904LB has WXGA 1280x800
resolution. This guide applies to all products. They are compatible with a
wide variety of computers and video devices.
Product specifications
To read the latest specifications on your multimedia projector, be sure to
visit our website at www.infocus.com, as specifications are subject to change.
Accessories
The standard accessories that came with your projector are listed in the
included Quick Start Poster/Booklet. Optional accessories can be found on
our website at www.infocus.com or at your retailer or dealer.
Online registration
Register your projector on our website at www.infocus.com/register to
activate your warranty and receive product updates, announcements, and
registration incentives.
4
Connector panel
audio in
composite
video
S-video
monitor out
computer
HDMI
audio out
security lock
5 volt
output
RS232
DisplayLink
connector
LitePort
RJ-45
reset
The projector provides both computer and video connection options,
including:
•VGA computer (2)
•HDMI
•S-video
•Composite video
• Separate assignable audio inputs for video and computer
• USB DisplayLink connector, for computer audio/video input. This
US
B connection also provides slide advance (and mouse control when
used with an optional remote control only)
The projector also provides the following connectors:
• Monitor out, to provide an image on your desktop computer as well as
on the pro
• LAN port for network control and web server.
• LitePort, for connecting a USB flash drive containing
• Audio out, to provide sound for external speakers
• A 5 volt DC output (see below)
• RS-232 connector for serial control. The Command
specifications and commands are on our website.
NOTE:
DisplayLink video and audio is not sent to monitor out and audio
out.
jection screen
images.
Line Interface (CLI)
VGA 1/2
composite s-video
composite
s-video
VGA 1
VGA 2
5 volt DC output
The coaxial 6.4mm x 2.2mm jack provides a constant 5 volt, 2 amp DC
output when the projector is on, and will also provide power when the
projector is in standby (powered off) if Network and DisplayLink items in
the Always-On Functions submenu are set to Yes. It is designed to provide
power for an InFocus LiteShow II wireless device, which allows wireless
projection. More information can be found on our website at
www.infocus.com or at your retailer or dealer.
5
Positioning the projector
10 ft high image
10 ft high image
bottom of image
1.24 ft above center
of lens
Projection angle
lens center
bottom of image
1.5 ft above center
of lens
Projection angle
lens center
(IN3904LB)(IN3902LB)
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general
guidelines:
• Position the projector on a flat surface at a
projector must be at least 4.9 feet (1.5m) from the projection screen.
• Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase
extension cables). To ensure adequate cable access, do not place the
projector within 6 inches (.15m) of a wall or other object.
• If you are installing the projector on the ceiling, we strongly
recommend using InFocus approved ceiling mounts for proper fitting,
ventilation and installation. Refer to the installation guide that comes
with the InFocus Ceiling Mount Kit (p/n SP-CEIL-UNIV) for more
information. The warranty does not cover any damage caused by use of
non-approved ceiling mount kits or by installing in an improper
location.
• Position the projector the desired di
distance from the lens of the projector to the screen, the zoom setting,
and the video format determine the size of the projected image.
• The image exits the projector at a given angle. IN3902LB image offset is
115%; IN3904LB image offset is 112.4%. This means that if you have an
image 10’ high, the bottom of the image will be 1.5' (IN3902LB) and
1.24' (IN3904LB) above the center of the lens.
right angle to the screen. The
stance from the screen. The
Table 1: (IN3902LB)
Range of distance to the screen for a given screen size
Distance to screen
Diagonal Screen
Size (inches/m)
Minimum distance
(feet/m)
Maximum
Distance (feet/m)
60/1.5 7’ 10”/2.4 8’ 7”/2.6
80/2.0 10’ 5”/3.2 11’ 6”/3.5
90/2.3 11’ 8”/3.6 12’ 11”/3.9
150/3.8 19’ 6”/5.9 21’ 6”/6.6
Table 2: (IN3904LB)
Range of distance to the screen for a given screen size
Distance to screen
Diagonal Screen
Size (inches/m)
Minimumdistance
(feet/m)
Maximum
Distance (feet/m)
60/1.5 6’ 6”/2.0 7’ 4”/2.2
80/2.0 8’ 8”/2.7 9’ 8”/2.9
90/2.3 9’ 10”/3.0 10’ 11”/3.3
150/3.8 16’ 4”/5.0 18’ 1”/5.5
6
Connecting a computer source
connect USB cable
connect computer cable
connect power cord
DisplayLink or VGA
If you have a Windows or Macintosh computer, connect the USB cable
between your computer's USB port and the projector's DisplayLink
connector*. Then to begin installation of the DisplayLink software:
Windows: Follow the instructions on the screen.
Macintosh: A folder will open containing
Installer.pkg. Open that file and follow the instructions on the screen.
* For detailed DisplayLink instructions and troubleshooting, and to
do
wnload the latest DisplayLink software, go to
www.infocus.com/support/displaylink.
Or, connect one end of the provided computer cable to the VGA 1 or VGA 2
connecto
r on the projector and the other to the VGA connector on your
computer. If you are using a desktop computer, you will need to disconnect
the monitor cable from the computer’s video port first (you can connect this
monitor cable to the Monitor Out connector on the projector, see below).
Connect the black power cord to the Powe
projector and to your electrical outlet. The Power light on the Status
Indicator Panel (on page 18) turns amber.
NOTE:
Always use the power cord that shipped with the projector.
a file named DisplayLink
r connector on the side of the
MOLEX
MOLEX
7
Optional computer connections
connect audio cable
connect monitor cable
connect RS-232 cable
connect CAT-5 cable
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the Audio In Computer connector on the
projector. You may also need an adapter.
If you are using a desktop computer and want to see the image on your
compute
monitor cable to the Monitor Out connector on the projector.
NOTE: Only
To display a presentation from a USB flash drive, see the Using LitePort
section on on page 43. This feature converts presentations to JPEG images
and eliminates the need for a computer
common wall plates and conference room input/output panels.
To advance slides in a PowerPoint presentation using the remote co
plug the USB cable between the projector's DisplayLink connector and your
computer. Then press the up and down arrow buttons on the remote control
to move through your slides.
You can control the projector from an LCD
other control device or computer by connecting an RS-232 cable to the
projector’s Serial Control connector. Specific RS-232 commands can be
found in the Service and Support section of our website.
The projector can be managed by ne
(RJ-45) connector. Detailed instructions on this feature can be found on our
website.
r screen as well as on the projection screen, connect the computer’s
VGA video is sent to the Monitor out connector.
source and can be integrated with
ntrol,
control panel, touch screen, or
tworking software through its Network
8
Displaying an image
press Power button
turn on computer or
video device
activate laptop’s external port
monitor key or
LCD/CRT key
FN key
Touch the Power button.
The Power button blinks green and the fans
comes on, the start up screen displays and the Power button is steady green.
It can take a minute for the image to achieve full brightness.
? No start up screen?
Get help on on page 19.
Turn on your computer or video device.
The image should appear on the pro
jection screen. If it doesn’t, press the
Source button on the projector’s keypad or remote.
start to run. When the lamp
If you are using a VGA cable to connect your computer
to the projector (instead
of DisplayLink):
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/
LCD key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop's documentation for
more information about your laptop's key combination or go to the InFocus
website at: http://www.infocus.com/Support/LaptopActivation.aspx.
? No laptop image? Try pressing
the Auto Image button on the keypad.
Get help on page 20.
? Is your laptop connected to the projector's DisplayLink connector? See the
InF
ocus DisplayLink Software User's Guide (available on the InFocus
website at www.infocus.com/displaylink) for troubleshooting information.
9
Adjusting the image
adjust height
release button
elevator foot
adjust distance
adjust zoom or focus
zoom (rear ring)
focus (front ring)
adjust keystone
adjust Basic Picture menu
If necessary, adjust the height of the projector by pressing the elevator foot
release button to extend the foot.
If necessary, rotate the leveling foot located at
Avoid placing your hands near the hot e
projector.
Position the projector the d
esired distance from the screen at a 90 degree
angle to the screen.
See the table listing screen sizes and distances on page 6.
Adjust the zoom or focus.
the rear of the projector.
xhaust vent at the side of the
If the image is not square, first make sure
that the projector is perpendicular
to the screen. If the image is larger or smaller on the top or bottom edge of
the screen, press the top Keystone button to reduce the upper part of the
image, and press the bottom Keystone button to reduce the lower part.
If the left or right side of the screen is larger
or smaller the other, you can
turn the projector to the left or to the right a few degrees to square the
image.
Adjust the Contrast or Brightness in the Basic Picture menu (on page 32).
For Aspect Ratio, keep in mind that DVD players must be configured for
in order to view the highest quality image (on page 11).
16:9
10
What is Aspect Ratio?
4:3 screen 16:9 screen
4:3
mode
16:9
mode
Native
mode
(NTSC
only)
Aspect ratio is the ratio of the image width to image height. Standard TV
screens and older laptops are 4:3; HDTV and most DVDs are 16:9; and
widescreen computers are 16:10. If you are projecting onto a screen, the
size/shape of the screen will influence the aspect ratio you decide to use. If
you are projecting onto a blank wall, there are no screen size restrictions.
What you plan to project will also help you choose between 4:3, 16:9 or
16:10. Many TV shows are 4:3, while most movies are 16:9.
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
escreen movies or HDTV, and Native for 4:3 content. If you have a 4:3
wid
screen you should still use 16:9 for widescreen movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Force Wide can also be enabled to
automatically resize less common aspect ratios to 16:10.
11
Connecting a video device
You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. You can connect the audio directly to the projector to get sound
from the built-in speaker, or you can bypass the projector’s audio system
and connect the audio directly from your source to a stereo or home theater
system.
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first.
Examples of tuners are digital cable boxes, VCRs, digital video recorders,
and satellite TV boxes. Basically, any device that can change channels is
considered a tuner.
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface.
HDMI provides an interface between sources, such as set-top boxes, DVD
players, and receivers and your projector. Plug an HDMI cable into the
video-out connector on the video device and into the HDMI connector on
the projector.
To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3-
patible source.
com
S-video connection
If your video device uses a round, four-prong S-video connector, plug an Svideo cable into the S-video connector on your video device and into the
Video 2 connector on the projector. Use the audio cable as described above.
Before connecting your projector, you should decide which aspect ratio you
want to use. The projector’s Aspect Ratio setting is accessed through the
Resize button on the remote or through the projector’s Basic Picture Menu
(on page 32).
Video device connections
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the
yellow Video 3 connector on the projector.
Plug the white connector of a Mini-plug
out connector on the video device and plug the red connector into the right
audio out connector on the video device. Plug the other end of the cable into
the Audio In Video connector on the projector.
Keep in mind that video output from compos
quality as S-video.
audio Y-cable into the left audio
ite connections is not as high
Keep in mind that S-video delivers highe
composite.
r quality video output than
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This
connector may be labeled “To Monitor” on the video source. Plug the
computer cable into the VGA 2 or VGA 1 connector on the projector.
Component video connection
If your HD video device has component connectors, an optional
Component to VGA adapter can be used. Plug the component cable into the
video device. Plug the other end of the component cable into the adapter
and plug the adapter into the VGA 2 or VGA 1 connector. Component offers
the highest quality analog video output. (Digital HDMI provides the
highest overall quality video output.)
12
LiteBoard™ Wand
Computer
USB Cable
The LiteBoard Wand works like a wireless mouse - but one that works in
midair, not on your desktop. Just hold the wand in your hand, and point it
at the projected image to point, click and drag. The wand works with all
your software, just like a regular mouse.
Computer System Requirements and Connections
For the wand to work, a LiteBoard-compatible projector needs to be
powered on and connected to your computer.
The LiteBoard Wand is compatible with any computer and operating
system that supports a standard USB mouse (including Windows,
Macintosh, and Linux). To set up your computer with the wand, make sure
a USB cable is connected between your projector's DisplayLink connector
and a USB port on your computer.
IMPORTANT: If you
connect the computer’s display output to the projector using a VGA or
HDMI cable.
Charging the Wand’s Battery
When the wand’s amber battery light starts to blink, its internal battery is
low (if the battery is fully discharged, you won’t be able to turn the wand on
by pressing its tip, L or R buttons).
To charge the battery, open the flap at the rear of the wand to expose the
wand’s USB connector. Then connect a USB cable between the wand and
the USB power adapter, or a computer (if connecting to a computer, make
aren’t using DisplayLink to project, you must also
sure the computer is powered on). The battery light will stay on while the
battery is charging, then it will turn off when the battery is fully charged.
When charging is finished, you can disconnect the USB cable (or keep the
cable connected and use the wand while it’s charging).
NOTE: 5-10 minutes of charging is e
full charge will take 6-8 hours and will allow 20-40 hours of non-stop wand
use.
Caution: The lithium battery is only rechargeable, and is not user serviceable
or user replaceable.
Caution: Always use the included USB cable and power adapter (or your
computer) to charge the wand.
nough for about an hour of wand use. A
How to Use the Wand
Follow these steps to use the wand:
1 Connect the projector and your computer with a USB cable (see
Computer System Requirements and Connections
2 Make sure the wand's battery is charged or charging (see
Wand's Battery
above).
3 Turn on the projector and make sure it's displaying the computer's
screen - set the source to DisplayLink, VGA 1, VGA 2, or HDMI (press
the source button on the projector or its remote if needed - you may
need to press it several times).
4 Turn on the wand by pressing its tip, L, or R button - the wand's green
Link light will start to blink.
5 Point the wand at the screen to point, click, and drag - just like a normal
mouse.
above).
Charging the
13
NOTE: See LiteBoard Wand Menu below for settings that let you fine-tune
USB connector
Link Light
Right mouse
button
Left mouse
button
Reset
button
Battery Light Middle mouse
button
Sensor
Tip
wand motion and clicking behavior. When you’re done, set the wand aside
and make sure it isn’t pointing at the screen; it will turn itself off
automatically after 1 minute.
If you have problems, see Troubleshooting (below).
Wand Position and Avoiding Shadows
Your Location Distance from the Screen
You can use the LiteBoard Wand right up against the screen, or around the
room. You might find that your pointing accuracy will improve if you get
closer to the screen. Also, avoid standing too far off from either side of the
screen.
Avoid Shadows!
The wand won't work if its tip is in a shadow or if it is pointing at a shadow:
Correct (no shadow) Incorrect (shadow)
Using More than One Wand
The projector can work with more than one wand, but you can only use one
wand at a time. When you want to switch to a different wand:
1 Point the current wand away from the projected image for at least 3
seconds.
2 Press the tip, L, or R button on the new wand to turn it on, and then start
using the new wand.
How to Hold the Wand
You can hold the wand the way you would hold a normal pencil or pen, or
you can hold it like a remote control - use in whichever position is most
comfortable. NOTES: If the wand is up close to the screen, you can press its
tip against the projection surface to click and drag. Not recommended for
use with fabric screens.
NOTE: S
to all wands used with that projector.
ettings in the projector's LiteBoard Wand menu (see below) apply
Wand Features
14
Buttons and Wand Tip
The wand's three top buttons are equivalent to the left (labeled 'L'), right
(labeled 'R'), and middle (labeled 'M') buttons on a mouse. The wand's tip is
also a button, and it's also equivalent to the left mouse button. NOTE: By
default, the M button changes wand motion between Normal and Draw.
Normal makes clicking easier, but Draw allows smoother motion. You can
change the M button to perform other functions, including a standard
middle button mouse click (see LiteBoard Wand Menu below).
Battery Light
The amber battery light shows the status of the
below for battery information). The battery light will turn on while the
wand is charging, and it will blink if the battery is low (2-4 hours of wand
use left).
Link Light
The green link light shows the status of the wand'
the projector. The link light will blink frequently (more than once per
second) when the wand is attempting to link to the projector; then it will
blink less frequently (about once every 4 seconds) after the wand has linked
to the projector. NOTE: The link light will stay off when the wand is off.
USB Connector
wand's built-in battery (see
s wireless connection to
Reset Button
The wand has a reset button, behind a smal
normal conditions, you should not need to reset the wand. See the
Troubleshooting section below for more information.
Internal Radio
The wand has a built-in wireless transmitter/receiver which it
communicate with the projector.
Lithium Battery Information
Manufacturer: KAYO Battery (ShenZhen) Co., Ltd.
Model: ICR14430
Rating: 3.6VDC/650mAh
Caution: Li
user serviceable.
thium battery is only rechargeable, and not user replaceable. Not
l hole on its underside. Under
uses to
LiteBoard Wand Menu
You can access the LiteBoard Wand menu from the projector's Setup menu.
To change the settings in this menu, highlight a setting, then press Select (on
the projector or its remote) one or more times - each press of Select will
change to the next value for the setting.
The wand's USB connector is
USB connector is only used for charging the wand's battery - using the
included USB power adapter, or a computer. NOTE: You can use the wand
while charging the battery, but after the battery is charged (battery light
turns off), you can unplug the USB cable and continue to use the wand
without a cable.
Sensor
The wand's optical sensor opening is located
block the sensor, and make sure it always has a clear view of the screen.
NOTE: The sensor won't work if you point it at a shadow or away from the
screen.
behind a flap on the back of the wand. The
above the wand's tip. Don't
Enabled:
this to Yes to allow wand use. Set this to No to prevent wand use.
controls whether the projector lets you use LiteBoard Wands. Set
15
Loading...