INFOCARE 1383 Users manual

To Power and Set Up the Weather Forecaster

Battery Power
2 AAA alkaline for base unit (not included).
2 AAA lithium (recommended) for remote sensor (not included).

Install Batteries into Base Unit
*Important: Install the base unit batteries first
batteries, for proper signal connection.
Base unit –use 2 AAA alkaline or lithium batteries (not included).
Remove the battery compartment cover on the back of the base unit. Install 2 AAA
batteries according to the polarity markings in the compartment. Replace the cover.

Set Current Weather Conditions

1. After installing the batteries into the base unit, the current weather icon flashes.

2. Press “Up” or “Down” to select the weather icon you believe most closely reflects

the current conditions in your area. (Partly Cloudy is the default setting).

3. Press “Time/Date” to select the displayed weather icon. The icon stops flashing.

4. The selected weather icon appears on all screens. (The temperature, humidity and

weather forecasts update after remote sensor is added.)

Install Batteries into Remote Sensor
*Important: Install the remote sensor batteries after
proper signal connection.
Remote sensor – use 2 AAA lithium batteries (not included).
Remove the screws from the battery compartment on the back of the remote (take care
not to misplace the screws). Install 2 AAA batteries according to the polarity mark ings in
the compartment. Replace the cover and the screws.

Battery Advice: Alkaline batteries will read outdoor temperatures from 14°F to 122°F (­10°C to 50°C).
Lithium batteries will read outdoor temperature s from -4°F to 158°F (-20°C to 70°C).
Although alkaline batteries may be used, lithium batteries are recommended for the wider
temperature range.

Set Up Remote Sensor

1. After installing the batteries into the base unit and then the remote sensor, place the
units close together for best setup connection.

2. Press and hold the “SYNC” button for 3 seconds to send a transmission sign al to the

, before installing the remote sensor

installing the base unit batteries for

remote sensor. Allow a few minutes for a connection as the “

” icon flashes and the

current temperature digits show dashes. When connected, the current temperature

updates an d the “

3. After a signal is received, position the remote sensor at an outdoor location within 200
feet of the base unit in a dry, shaded area. Direct sunlight will heat the casing and inflate
temperatures readings.

Important: Though the remote is weather resistant, it shou ld be placed away from direct
sunlight, rain, snow and should never be submerged in water.
.

Allow at least 6
forecast readings. During that time, indoor temperatur e will update every 30 seconds
and appears on the forecast screens. Outdoor t emperature and humidity show “—”,
and all weather icons are identical.

5. When the units begin to forecast weather conditions after the first 6 hours, all

temperature and weather screens will update with new forecasts.

6. The remote sensor will automatically transmit weather conditions to the base unit.

• Indoor temperature readings will update approximately every 30 seconds.

• Current outdoor temperature readings will update approximately every 1
minute.

•Outdoor temperature, outdoor humidity and weather condition forecasts will

update every 6 hours during the first 24 hours of operation.
After the first 24 hours, updates occur every 1 hour.
Please note: if the remote senses identical weather conditions over a 24 hour period, the
screens will all show identical readings.

Set Clock and Date

1. Press and hold “TIME/DATE” for 2 seconds, then release.

2. Press “UP” or “DOWN” to change the hours. Press “TIME/DATE”.

3. Press “UP” or “DOWN” to change the minutes. Press “TIME/DATE”.

4. Press “UP” or “DOWN” to change the month. Press “TIME/DATE”.

5. Press “UP” or “DOWN” to change the date. Press “TIME/DATE”.

6. Press “UP” or “DOWN” to change the year. Press “TIME/DATE”.

7. Press “UP” or “DOWN” to switch between a 12 or 24 hour clock. Press
“TIME/DATE”.

8. Weather Forecaster and Cl oc k/D ate setup are complete.

” icon disappears.

hours for the remote to analyze weather conditions and report

Reading the Weather Forecaster

5 forecast displays over 24 hours
Forecast screens will rotate as time periods change, with the upcoming time period
appearing at the left.

Today Evening
Today Ove rnight
Tomorrow Morning
Tomorrow Midday
Tomorrow Afternoon

(6PM-10PM)
(10PM-6PM)
(6AM-10AM)
(10AM-2PM)
(2PM-6PM)

Additional Features

°C/°F Selection
Press the “C/F” button to switch between Fahrenheit and Celsius temperatures.

Backlight
Press the Backlight button on the top of the base unit. The LCD screen will light up for 5
seconds.

Low Battery Warnings

Base unit – replace both batteries when the “

” icon appears on the right side of the

screen.

Remote sensor – replace both batteries when the “

” icon appears on the left side of

the screen.

Tips

Setup:
Place the base unit as close as possible to the remote se ns or duri ng se tup.
This will ensure the best reception of si g nals as you set up your wireless forecaster.

Location:
Position the base unit and remo te sensor within the effective transmission range of 20 0
feet (60 meters).

Place the base unit indoors in a well-ventilated location away from direct sunlight.

Place the remote sensor in a dry, shaded area. Direct sunlight will heat the casing and
inflate temperatures readings.

Important: Though the remote unit is weather resistant, it should be placed away from
direct sunlight, rain, snow and should never be submerged in water.

Note: The effective range is greatly affected by the building materials and where the base
and remote units are positioned. Try various set ups for the best results. Check to make
sure the transmission path is clear of obstacles and interference. Shorten the distance
between base and remote units when nec es s a ry.