Infinity Drain WW 5 User Manual [en, es]

Center Drain Series

Installation Instructions

LTD 5

WW 5

LT5-2

LTD5-2

W5-2

WW5-2

RTD 15

RTD 15-2
RTD 15-3

LW 5

G 3

L5-2

LW5-2

TD 15

TD 20

TD 15-2
TD 15-3

G 1 G 2

G 4

TD 20-2
TD 20-3

The Center Drain Series are intended for use with the following waterproong methods:

Hot Mop ° Copper Pan ° CPE Rubber Liner (Chloraloy®) ° PVC Liner ° Lead Pan ° Fiberglass

°

Made in the U.S. A.

Infinity Drain • 18 Secatoag Avenue, Port Washington, New York 11050

Phone [phone] • Fax [phone] • www.InfinityDrain.com

Dimen sion are subje ct to Manufac turer s tolerance and change w ithou t notic e. We can a ssume n o resp onsib ility for

Las dimensiones están su jetos a la tolerancia del fabricante y cambio s in prev io aviso. No po demos a sumir n inguna

responsabilidad por el us o de dato s a sustituir lo s nulos .

use of su pers eded or void dat a.

Series Components:

LTD 5 Series

LT5-2 SS 5" x 5" Straine r Only wi th Sati n Stainl ess Finish

LT5-2 PS 5" x 5" Strain er Only wit h Polis hed Stai nless Fi nish

CDI 22 Clamp Down Drain Cast Iron

CDA 22 Clamp Down Drain ABS

CDP 22 Clam p Down Dr ain PVC

TD 15 Series

T15 A SS 5" x 5" Strainer Only - Satin Sta inless Finish

T15 A PS 5" x 5" Strai ner Only - Polishe d Stain less Fini sh

CDI 42 4" Throa t x 2" Outlet Clam p Down Drain Ca st Iron

CDI 43 4" Throa t x 3" Outlet Clam p Down Drain Ca st Iron

CDA 42 4" Thro at x 2" Out let Clamp Down Dr ain ABS

CDA 43 4" Thro at x 3" Out let Clamp Down Dr ain ABS

CDP 42 4" Thr oat x 2" Ou tlet Cl amp Dow n Drain PV C

CDP 43 4" Thr oat x 3" Ou tlet Cl amp Dow n Drain PV C

TKE Y Lif t Out Key

HS 4 4" Hair St rainer S tainl ess Ste el Thro at

WW 5 Series

W5-2 SS 5" x 5" Wedge Wire Strai ner - Satin Stai nless Fi nish

W5-2 PS 5" x 5" Wedge Wire Straine r - Polished Stain less Fini sh

CDI 22 Clamp Down Drain Cast Iron

CDA 22 Clamp Down Drain ABS

CDP 22 Clam p Down Dr ain PVC

G Series Components (Each sold separately)

G 1 Herr ing Stra iner

G 2 Line St rainer

G 3 Squar e Strain er

G 4 Ott o Strain er

T 2 Residential 5" x 5" Stainl ess Steel 2” Thr oat

T 4 High Fl ow 5" x 5" Stain less St eel 4” Th roat

MG 5 5" x 5" Mud Guard

RTD 15 Series

RT 15A 5" Round T ile Drai n Strainer

CDI 42 4" Throat x 2" Out let Clamp Down Dra in Cast Iro n

CDI 43 4" Throat x 3" Out let Clamp Down Dra in Cast Iro n

CDA 42 4" Thro at x 2" Out let Clamp Down Dr ain ABS

CDA 43 4" Thro at x 3" Out let Clamp Down Dr ain ABS

CDP 42 4" Thr oat x 2" Ou tlet Cl amp Dow n Drain PV C

CDP 43 4" Thr oat x 3" Ou tlet Cl amp Dow n Drain PV C

TD 20 Series

T20 A SS 8" x 8" Str ainer On ly - Satin Stai nless F inish

T20 A PS 8" x 8" Str ainer On ly - Polishe d Stai nless Finish

CDI 42 4" Throat x 2" Out let Clamp Down Dra in Cast Iro n

CDI 43 4" Throat x 3" Out let Clamp Down Dra in Cast Iro n

CDA 42 4" Thro at x 2" Out let Clamp Down Dr ain ABS

CDA 43 4" Thro at x 3" Out let Clamp Down Dr ain ABS

CDP 42 4" Thr oat x 2" Ou tlet Cl amp Dow n Drain PV C

CDP 43 4" Thr oat x 3" Ou tlet Cl amp Dow n Drain PV C

TKE Y Lif t Out Key

HS 4 4" Hair St rainer

LW 5 Series

L5-2 S S 5" x 5" Strainer On ly - Satin Stai nless F inish

L5-2 P S 5" x 5" Strain er Only - Po lished Stain less Finish

L5-2 ORB 5" x 5" Strainer Only - Lifetime Oil Rubbe d Bronze Fini sh

CDI 22 Clamp Down Drain Cast Iron

CDA 22 Clamp Down Drain ABS

CDP 22 Clam p Down Dr ain PVC

Note: Installer must verify all rough-in
dimensions prior to installation and consult
local and national codes. Conformit y and
compliance to local and national codes are
the responsibility of the installer.

Optional Components: (Not Included)

UCP 2 Un iver sal 2" Clampin g Plate

UCP 4 Un iver sal 4" Clamping Plate

ERB Eccent ric Reducing B ushing 4"x2"

Tenga en cuenta: Instalador debe

comprobar todas las dimensiones en las
partes previa a la instalación y consultar
localmente y nacionalmente los códigos. La
conformidad y el cumplimiento de códigos

local y nacional es responsabilidad del

instalador.

2

Section A-A

TD 15

Section A-A

TD 20

Section A-A

RTD 15

Section A-A

LTD 5

Section A-A

G Series with

T2 & CDI22/CDA22/CDP22

Section A-A

WW 5

Section A-A

G Series with

T4 & CDI42/CDA42/CDP42

3

Section A-A

LW 5

Section A-A

G Series with

T4 & CDI43/CDA43/CDP43

(C2)

KEY

(C1)

(A) Str ainer

(B) Throat

Waterproong Membrane

(C) Clamp Down Drain Asse mbly

CDI22/CDA22/CDP22/
CDI42/CDA42/CDP42/
CDI43/CDA43/CDP43

Installation

1. Connec t the clamp down drain assembly

(C) to existing waste line via no-hub rubber
coupling, PVC cement, or ABS pipe cement
and allow drain body (C2) to recess into
suboor. Ensure that drain assembly (C) is
level. Unscrew and remove top clamp down
plate (C1) from drain body (C2).

1

Suboor

(C) Clamp Down
Drain Assembly

2. Spread a primary mortar bed across the
intended shower area. Pitch this bed in four
directions towards the drain body (C2).

3. When mortar layer is dr y, perform
necessary waterproong (PVC Liner,
Rubber Liner, Lead Pan, Copper Pan, Hot
Mop, Fiberglass) as per local code. Ensure
waterproong layer reaches the edge of the
hole in the drain body (C2).

(C1)

(C2)

Rubbe r

Coupling*

Waste Line

Instalación

1. Conecte la sujeción del drenaje (C) a la

existente línea de desecho a través del
acoplamiento de goma no-hub, cemento de
PVC, o tubo de ABS de cemento y permita que
la sujeción (C2) a que rebaje en el piso. Asegure
que la asamblea (C) este anivelado. Destornillar
y remueva la placa (C1) de la sujeción (C2).

3

(C) Clamp Down
Drain Assembly

Waterproong Membrane

*Not pr ovide d by Innity Drain kit s

2. Propagar una capa de mortero a través de
la zona de ducha prevista. Bree este mortero
en cuatro direcciones hacia el drenaje (C2).

3. Cuando el mortero este seco, realice la
impermeabilización necesaria (PVC Liner,
Rubber Liner, Lead Pan, Cooper Pan, Hot
Mop, Fiberglass) según el código. Asegure
que la capa de impermeabilización alcance
el borde del agujero en el drenaje (C2).

Primary Mot ar Bed

4

4. Reattach the top clamp down plate (C1)
to the clamp down drain body (C2) over the
waterproong layer using bolts. Thread the
throat (B) of the drain into top clamp down
plate (C1). Adjust to the desired height. Turn
clockwise to lower, counter-clockwise to
raise. When determining desired height,
include thickness of mortar, thinset and
nishing material.

(B) Throat

4. Vuelva a colocar la par te superior de la
placa (C1) al drenaje (C2) sobre la capa de
impermeabilización usando tornillos. Rosca
el cuello (B) del drenaje en la placa del
drenaje (C1). Ajústelo a la longitud deseada.
Gire hacia la derecha para bajar, hacia la
izquierda para aumentar. Al determinar
la altura deseada, incluía el espesor del
mortero, thinset y el material terminado.

(C1)

(C) Clamp Down
Drain Assembly

(C2)

Waterproong
Membrane

Primary Mot ar Bed

Model Overall Minimum Height Overall Maximum Height*

LTD 5 1 ⅛” 2 ¼”

RTD 15 ¹³⁄¹⁶” 1 ⁷⁄¹⁶”

TD 15 1 ⁵⁄¹⁶” 2 ¹⁄¹⁶”

TD 20 1 ⁵⁄¹⁶” 2 ¹⁄¹⁶”

WW 5 ¾” 1 ¾”

LW 5 ⁷⁄¹⁶” 1 ⁷⁄¹⁶”

G-Se ries – T2 ⅝” 1 ⅝”

G-Se ries – T4 ⅝” 1 ⅝”

5. Using desired oor material, mark the
thickness of the material along the outside
of the throat (B), so that it will nish 1/16”
above the channel. Lay gravel or other porous
substrate over weep holes of the top clamp
down plate (C1). Spread a nal mortar bed up
to the marked thickness, less the thickness of
thinset. Pitch this bed in all directions toward
the center drain. Once dry, apply a bead
of silicone caulk around the throat (B). Lay
thinset and nishing material. Have material
nish to the edge of the throat (B). DO NOT
allow nishing material to nish on top of the
stainless steel channel edge.

5. Usando el material deseado, marque el
espesor del material a lo largo de la parte
afuera del cuello (B), para que termine
1/16” arriba del canal. Coloque grava u otro
sustrato poroso sobre los oricios de drenaje
(C1). Propagar un motero hasta el espesor
marcado, menos del espesor del thinset. Bree

esto en cuatro direcciones hacia el centro

drenaje. Una vez que este seco, aplique un
cordón de silicona alrededor de cuello (B).
Coloque thinset y material terminado al
borde superior del cuello (B). NO PERMITA
que el material terminado termine enzima del
canal de acero inoxidable.

5

Before nishing

material

Antes que el material

esté terminado

After nishing

material

Después que el material

esté terminado

6. LTD 5/RTD 15/TD15/TD20 SERIES ONLY:

Spread a layer of mortar into the strainer (A),
allowing for thinset and nishing material to
nish 1/16” above the metal frame. Allow to
dry, spread thinset and lay material. Place top
strainer (A) into the throat (B) of the drain.

WW 5 SERIES: Place strainer (A) into throat (B).

LW 5 SERIES: Place the strainer (A) into the

throat (B) and fasten using screws at each
corner.

G SERIES: Drill a 1” hole in the marked
location of the factory installed mudguard.
Place your nger into the hole and pull out.
Place the magnetic G-Series strainer (A) into
the throat (B) (Each sold separately)

6. LTD 5/RTD 15/TD15/TD20 SOLAMENTE:

Propagar una capa de mortero en el strainer
(A), permitiendo el thinset y material terminado
que termine 1/16” por encima de la estructura
de metal. Permita que se seque, propagar
thinset y tender el material. Coloque la parte
superior (A) en el cuello (B) del drenaje.

WW 5 SERIE: Coloque el strainer (A) en el cuello (B).

LW 5 SERIE: Coloque el strainer(A) en el cuello

(B) y sujetar con tornillos en cada esquina.

G SERIE: Perfore 1” agujero en la locación
marcada del guardabarros que está
instalado. Coloque su dedo en el agujero y
retírelo. Coloque el magnético G-serie (A) en
el cuello (B) (Cada uno se vende separado)

Backer Board

Thinset

Finishing Material

Final Mortar Bed

Waterproong

Primary Mor tar Bed

Suboor

Clamp Down

Floor Drain

6