Model OVTR 1
3- Way Full-Range Bookshelf Speakers
Owner's Manual
OVTR 1 Part #331252 - USA 120 Vac Only
IMVO SAFET¢INSTRUCTIONS
I) l_d _-, -/dl the safetyand operatingimm_ous should
be read before the p_roduct is operated.
2) Retain hstructlom - The safety and operatingin.m'uctionsshould
be retainedfor fiamrereference.
5) HeedWarnings- All warningson the productandin the operating
instructionssha,_lbeadheredto.
4) Folio,#Iastmalons - All operatingand useinstructions should be
followed.
5) Cleaning- Unplugthisproductfromthe walloudet beforedeaning.
Do notuseliquidcleanersoraerosoldeanets. Usea dampdoth for dean-
ing. ExceptiomA product thatis meant for uninterrupted serviceand
that for some specificreason,such as the possibilityof the lossof an
anthorizadon code for a CATVConverter, is not intended to be
unpluggedbythe userfor deaniugoranyotherpurpose,mayear.ludethe
reieereficeto unpluggingthe productin thedeanhg descriptionotherwise
requiredabove.
6-) Attachments - Do not use attachments not recommendedby the
product manufacuaer asthey maycausehazards.
7) Water and Moisture- Do not use this product nearwater - for
example,neara bath tub, washbowl,kitchen sink, or laundrytub; in a
wet basement;,or near a swimmingpool; and the like.
8) Accessories- Do not phce this product onan unstablecart, stand,
tripod, bracket,or table. The productmayfall,causingseriousinjuryto
achildoradult, and seriousdamageto the product. Useoulywithacart,
stand, tripod, bracket,or table recommended by the manufacturer,or
sold with the,product. Any mounting of the product should followthe
manufacto_,_sinstructions, andshould usea mountingaccessoryrecom-
mendedby the manufacturer.
9) Aproduct andcartcombinationshould be movedwith care. Quick
stop,excessiveforce,andunevensurfacesmaycausethe product and cart
combinationto overturn.
I0) Ventilation- Slotsand openingsin the cabinetareprovidedfor ven-
tihtiun and to ensu_ reliableoperationof the productandto protect it
from overheating,and these openingsmustnot be blockedor covered.
Theopeningsshould neverbe blockedbyplacingthe producton a bed,
sofa,rug,or other similarsurface.Thisproduct should notbe placedin a
built-in installationsuch as ab_,keaseorrack unlessproperventilation
is providedorthe manufacturers instructionshavebeen adheredto.
11) PowerSources- Thisproduct shouldbeoperatedouly fromthetype
ofpowersourceindicatedonthe markinglabel.Ifyou arenotsureof the
typeof powersupplyto yourhome, consultyourproductdealerorlocal
powercompany.Forproductsintendedto operatefrom batterypower,or
othersources,referto the operatinginstructions.
12) Grounding orPolarlzation- This product maybe equipped witha
polarizedalternatlng-current line plug (a plug having one blade wider
than theother).Thisplugwillfitinto thepoweroutletonlyonewaFThis
is a safetyfeature.If you areunable to insertthe plugfullyinto the out-
let, try reversingthe plug. If the plug should stillfail to fit, contact your
electricianto replaceyour obsoleteoudet.Do not defeatthe safetypur-
poseof the polarizedplug.
13) Power-CordProtection - Power-supplycordsshould be routedso
that they arenot likelyto be walkedonorpinched by items placedupon
or against them, paying particularmention to cords at plugs,conve-
niencereceptacles,and the point wherethey exitfrom the product.
14) Outdoor Antenna Grounding - If an outsideantenna or cablesys-
tem is connected to the product, be sure the antenna or cablesystemis
_ru_l.undedso as-€oprovide some protection againstvoltagesurges and
t-up static charges. Ardde 810 of the NationalElectricalCode,
ANSI/NFPA70, providesinformationwith regardto proper grounding
ofthe mastand supportingmuctu_ groundingof the lead-inwireto an
antenna discharge"unit, sizeofgrouncling"conductors,location of anten-
na-dischargeunit, connection togroundingdectrodes,and requirements
for the groundingdectrod_Seethe followingfigure.
NqTI_HA
a--""_ IT=ADUq
_P.E
• _'/ ,/h_ITE;_IA
DISCHARGE UNIT •
(/dEC SECTION 810-21)
l
15) Lighming- Foraddedprotectionforthisproductduringa lighming
storm,orwhenit is leftunattendedand unusedforlongperiodsof time,
unplug it fromthe walloutletand disconnectthe antenna orcablesys-
tem. This will prew_ntdamage to the product dueto lightningand
power-linesurges.
16")PowerLines- An outsideantennasystemshould not be locatedin
the vidnity of overheadpowerlinesor otherdectriclight or power cir-
cuits, or where it can fall into such power lines or circuits. When
installingan outsideantenna system, extremecare should be taken to
keep from touching such power lines or drcuitsas contactwith them
EmCTmC_ I _-_ I I - J (N_C_C'no_e*0-2_)
s_ce. -'--.-bn-I / / /
•GROUNDING COf, RXJCTORS
GROUND CLAMPS
(NEC SECTION 810-211
mightbef=£.
17) Overloading- DOnotoverloadwalloudets,extensioncords,orinte-
gralconveniencereceptaclesasthis can resultin a risk of fireordectric
shock.
18) Object and LiquidEntry- Neverpush objectsofany kind into this
productthrough openingsas theymaytouch dangerousvoltagepoints or
short-ourpartsthat could resultin a fireordectricshock.Neverspillliq-
uid of any kind on the product.
19) Servicing- DOnot attempt to servicethisproduct yoursdf asopen-
ingorremovingcoversmayexposeyou to dangerousvoltageorotherhaz-
ards. 1_e.ferall servicingtoqualifiedservicepersonnd.
20) DamageRequiringService- Unplugthisproductfrom thewallout-
letand referservicingto qualifiedservicepersound under the following
conditions:
a) Whenthepower-supplycordorplugisdamaged.
b)If liquid hasbeenspilled,orobjectshavefallenintotheproduct.
c) If the product hasbeenexposedto rainorwater
d) If the productdoesnotoperatenormallybyfollowingtheoperating
instructions.Adjustonlythosecontrolsthat arecoveredbythe operating
instructionsasan improperadjustment of othercontrolsmayresultin
damageand willoftenrequireextensiveworkbya qualifiedtechnicianto
restorethe product to its normaloperation.
e) If the producthasbeendroppedor damagedin any wa_
f) When the productexhibitsa distinctchangein performance- this
indicatesa needfor service.
21) Ik'placementParts- Whenreplacementpartsarerequired,besurethe
servicetechnicianhas usedreplacementparts speci_edbythe manufactur-
er or that have the same characteristics as the original part. Unauthorized
substimdonsmayresultin fire,dectricshock,orotherhazards.
22) Sak_ Check - Upon completion of any serviceor repairsto this
product,asktheservicetechnicianto performsafetycheckstodetermine
that the productis in properoperatingcondidon.
2.3)Wallor CeilingMounting - The product should be mountedto a
wallorceilingonly asrecommendedby the manufacturer.
24) Heat- The product shouldbe situatedawayfrom heatsourcessuch
asradiators,heatregisters,stoves,orotherproducts(includingamplifiers)
that produceheat.
P/N 330100-O01
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
The_ flashw_ arrowhead_,,_,
within an equilateral triangle, is intended
to alert the user to the presenc._ of
=ninsulated"dangerousvoltage"within the
product's enclosure that may be of sufficisnt
magnitude to constitute a risk of electric
shock topersons.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equi-
lateral triangle is intended to alert the user
to the presence of important operating and
mainJenance (servicing) instructions in the
literature accomtxmfing the product.
THIS INFINITY PRODUCT IS DESIGNED FOR (USA) 120 VOLT USE ONLY!
FOR DETAILED SAFETY PRECAUTIONS, PLEASE SEE THE ENCLOSED
LEAFLET "IMPORTANT SAFETY INSTRUCTIONS" (P/N 330100-001).
OVTR1 OVTR1
Front Side
121/2"
(318 mm)
5¾"
(146 mm)
COMPOSITIONS OVERTURE
OVTR 1
OVERALL DIMENSIONS
OVTR1
Top
(318 ram)
INfRODUCTION
3-WAY BOOKSHELF
SPEAKERSWITH
INTEGRATEDPOWERED
SUBWOOFERS...
ABOUTTHIS MANUAL...
PARTSLIST...
The Infinity Compositions Overture OVTR 1 speaker system is a super-
compact, 3-way, full-range bookshelf or stand-mounted speaker with an
integral powered subwoofer. The OVTR 1 is ideal for use where space is
at a premltun.Withits-widebandwidthand uniform response, it excels
in the accurate reproduction of music, but its high efficiency and ability.
to produce realistic sound levels with minimal amplifier power make it
equally suited for use in the finest home theater system.
To start enjoying your new pair of Compositions Overture OVTR 1
speakers, first read and then perform all instructions listed in this
manual, as well as those found in the owner's manuals of associated
components in your audio system. Also, please read the enclosed
Important Safety Instructions for detailed safety precautions. Save all
instructions for future reference. These speakers are covered by a
limited five-year warranty (see the back cover), so save the bill of sale to
protect your purchase and aid in any service-related questions.
UNPACKING THE SPEAKERS
Finish unpacking the speaker box. Be careful Kfting the speakers, since
they are heavier than they appear. If you suspect damage from transit,
report it immediately to your dealer and/or delivery service. Keep the
shipping cartons and packing materials for future use. Open the
accessory pack and verify the following contents:
• (2) Molded Feet (For Vertical Placement)
TOOLSANDSUPPLIES
(NOT ENCLOSED)...
• (4) Small Self-Adhesive Feet (For Horizontal Placement)
• (4) Large Self-Adhesive Feet (For Horizontal Placement)
• (2) Grilles
• (4) Spare 2AG 3A SB 250V Fuses
• Owner's Manual (P/N 331214-001) and Warranty Registration' Card
You may also need the following tools and supplies:
• High-quality speaker wire (also see Wiring The System on page 5)
• Wh'e strippers
• Small fiat-blade screwdriver (for fuse replacement, if needed)
• (4) Banana plugs or spade terminals (optional)
Compositions Overture OVTR I-Owner's Manual • 1
PLANNINGYOURSYSTEM
STEREOPLACEMENT...
Figure 1. Compositions Overture
OVTR I speakers can be positioned
vertically or horizontally for
placement on a shelf or stand. Make
sure the side-firing woofer is at least
2" away from an adjacent object,
shelf, or wall.
Before decicling where to place your Compositions Overture OVTR 1
speakers, survey your room and keep the following points in mind:
The OVTR 1 includes a side-firing woofer that requires a mlnlmllm
2" clearance from an object, shelf, or wall, whether placed vertically[
or horizontally, on a bookshelf or stand (see Figure 1).
NOTE: The stand must be large enough to fully support the speaker.
For vertical placement, make sure the woofers are facing toward or
away from each other. For stability, install the enclosed feet (see
Installing Feet and Grilles on page 4).
i
For best results, try placing the speakers closer together than the
distance to the listening area.
Refer to Figure 2 when placing speakers for best bass level and
stereo image (also see Operating The System on page 6).
Vertical OVTR1
side-firing
Woofer
/-
-- Will or
Other Object
Shelfor Other Object
I I
,.--_,:;
I II I
I I| I
I II _"
I II _"
I II I|%_
I Ii _i i,,
Horizontal 0
OVTR1
.._-_ _6___,_
lidS-firing
2" (rain.)
',___woo_icy__,
2" (mln.)
Figure 2. Experiment with speaker
placement to obtain the best bass level
and stereo imaging in your room.
Channel improvestereo Channel
2 * Compositions Overture OVTR 1 -Owner's Manual
ove speakers towards corners to increase bas_W
cS/__"t t' Q "
Left inwardto Right
imaging
ListeningArea
PLANNINGYOURSYSTEM (CONT'D)
HOME THEATER
PLACEMENT...
Figure 3. Compositions Overture
OVTR I speakers are suitable for use
in a home theater system.
Compositions Overture OVTR 1 speakers are also suitable for use in
reproducing home theater sound, as shown in Figure 3:
• For front left and right channels, place one OVTR 1 speaker on the
left and another on the right, on bookshelves or stands, along either.
side of the television monitor.
For surround left and right channels, place one OVTR 1 speaker on
the left and another on the right, on bookshelves or stands, behind
the listening area.
For center channel use, place one OVTR 1 speaker in the horizontal
position on top of or below the television monitor.
Since the speakers are magnetically shielded, you can set them in
very close without worrying about the field distorting the TV picture.
NOTE: Contact your local Infinity dealer about adding a subwoofer toyour
system for deep bass impact on sound effects and music.
Center
(on top or below TV)
FrontLeft
(onshelf)
Front Right
(onshelf)
Rear Left
ListeningArea
Compositions Overture OVTR 1 - Owner's Manual • 3
INSTAI22NG FEET AND GRmLES
Compositions Overture 0VTR 1 speakers include two types of feet for
vertical or horizontal placement on a shelf, table, or speaker stand.
VERTICALPLACEMENT...
Figure 4. This illustration shows how
to install a molded foot for the
vertical p[acement of a Compositions
Overture OVTR I speaker.
To insure proper woofer firing, temporarily position the speakers so that
the woofer grilles face each other. On each molded foot, peel the backiv, g
from the self-adhesive tape and press each foot into its respective slot,
as shown in Figure 4. Insert a grille into each speaker, so the logo is
nearest the foot. Flip each speaker ovei" and place them in your system.
0 PeelBackingFromTape
(ontopoffoot).
OVTR1
(verticalrearviewswith
woofersfacingeachother)
• PlaceFootInto SlotAndFirmly
PressAgainstSpeakerBottom.
HORIZONTAL PLACEMENT...
Figure 5. This illustration shows how
to install self-adhesive feet for the
horizontal placement of a
Compositions Ove_ure
OVTR I speaker.
Place two small self-adhesive feet on each speaker bottom, as shown in
Figure 5. Depending on where you plan to put the speaker (e.g., TV top),
place two large self-adhesive feet 4 to 6 inches away (refer to Figure 5).
Insert a grille into each speaker, so the logo is nearest the foot. Flip
each speaker over and place them in your system.
0VTR1
(horizontal sideview
wooferontop)
O PeelBackingFrom(2) LargeAnd
(2) SmallSelf-AdhesiveFeet.
4 * Compositions Overture OVTR 1- Owner's Manual
WIniNG SYSTEM
TURN OFF ALLPOWER...
IMPORTANT!
IMPORTANT!
Figure 6. Compositions Overture
OVTR I speakers feature gold-plated
terminals that can be connected in
several different ways; e.g., banana
plugs, spade terminals, and direct
wiring (as shown here)
After placing the speakers, you are ready to connect your system. First
turn off all audio system power. Use high-quality speaker wire to make
your connections. For speaker connections, use #18 gauge speaker wire
(or #16 for runs over 25 feet) with polarity coding. The side of the wire
with a ridge or other coding is usually considered negative polarity "
(i.e., - ). Also, consult the owner's manuals that were included with
your amplifier, receiver, or television to confirm connection procedures.
If your system includes a Dolby® Surround Pro Logic or AC-3
preamplifier or AW receiver, set the center,channel mode to NORMAL.
This will route the low frequencies (below 100 Hz) away from the
eenter_hannel speaker to the front left and right speakers.
Observe polarities when making speaker connections, as shown in
Figures 6 and 7 below. Connect each + terminal on the back of the
amplifier, receiver, or television to the respective + (red) terminal on
each OVTR 1 speaker. Similarly, connect the (black) terminals in the
same way.
Do not reverse polarities (i.e, + to - or - to +) when making connections.
Doing so will cause poor imaging and diminished bass response.
OVTfl1
(rearview)
ooO o°°
Figure Z v_rwing diagram shows
polarity connections for onechannel
of a stereo or home theater system.
Receiveror
Amplifier
(rear view)
CONNECTINGSPEAKERSDIRECTLYTOWIRES
OVTR1
(rear view)
blk- + red
Compositions Overture OVTR 1 - Owner'sManual * 5
IMPORTANT!
POWER ON...
CHECKING PLAYBACK...
OPERATING THE SYSTEM
Each Compositions Overture OVTR 1 speaker system contains a built-in
powered subwoofer. For your convenience, the system is not fitted with a
power on/off switch. Instead, an auto-sense circuit will instantly switch
the system on when anaudio signal is present, and will automatically
revert to standby (drawing only 7 watts) when audio is absent for a
min'imum of 10 minutes. A dual-color'Power On _ LED (see Figure 8
below) glows red when the amplifier is the stand-by mode and green
when the amplifier is on.
If on/off switching is desired, connect the OVTR l's ac power cord to an
ac switched outlet. If you plan to leave for an extended period of time
(e.g., vacation), switch the system off (or unplug the ac power cord).
This product is designed for (USA) 120 Vac use only. Do not connect it to
any other Une voltages.
1. After speaker wiring has been completed, connect each speaker's ac
power cord to the nearest ac receptacle. You should see an LED
illuminate, indicating the amplifier is on (see Figure 8 below). If not,
verify the ac outlet is delivering power or refer to Troubleshooting on
page 8.
o
Check the speakers for playback by first setting the audio system
volume control for a minimum level, and then applying power to your
system. Play a favorite music or video segment and increase the
volume control to a comfortable level.
!
Figure 8. Located on each OVTR l"s
rear panel are a BASS level control
and a dual-color _PowerOn LF.D.
NOTE: You should hear balanced audio reproduction across the
entire frequency spectrum. If not, check all wiring connections and
refer to the _TroubIeshooting _ section on page 8 for more help.
OVTR1
(rearview)
--m
• o°°° 4 ql° ° u ° 0 q
• • _ OVTR1
6 * Compositions Overture OVTR 1 - Owner's Manual
OPERATING THE SYSTEM (CONT'D)
So
Listen to a variety of music selections and note the bass level. If you
feel there is too much bass, you can reduce it by adjusting the BASS
control from the _normal _ center-detent position towards the MIN
setting (see Figure 8 on previous page). Conversely, if you want more
bass output, rotate the level control towards the MAX setting. "
JUDGING-BASSLEVEL...
IMPORTANT!
NOTE: The amount of bass you hear will be affected by a number of
different factors, including the room's size and shape, the construction
materials used to build the room, the listener's position relative to the
speakers, and the position of the speakers in the room. If there is too
much bass, move the speakers away from nearby walls. Conversely, if
you want more bass, place the speakers closer to the walls (also see
Figure I on page 2).
REPLACING THE FUSE
Compositions Overture OVTR 1 speakers each use a built-in fuse to
protect the subwoofer amplifier. To replace a fuse with a new one (see
enclosed spare), perform the following procedure:
1. Unplug the speaker's ac power cord. Then turn the speaker around
to access the fuse holder on the rear panel (refer to Figure 9 below).
1
Using a small fiat-blade screwdriver, place the tip in the indent and
turn the fuse cap counter-clockwise.
1
Remove the old fuse and replace it with a new one having the same
value and rating, a 2AG 3A SB 250V fuse.
Do not substitute the blown fuse with another fuse value or
rating. Doing so will void the warranty.
.
Insert the cap holding the new fuse into the holder and turn,
clockwise to lock it.
Figure 9. The OVTR l's fuse is
located on the rear panel next to the
ac power cord.
5. Rotate the speaker to its original position. Then plug the speaker's ac
power cord back into the nearest ac outlet.
OVTR1
(rearviow)
@
(
Compositions Overture OVTR 1 - Owner's Manual • 7
FUSE3A
250V
OVTR1 FUSE
)
CARE OF YOUR SPEAKER SYSTEM
The dark grey metallic finish does not require any routine maintenance.
When needed, use a soi_ cloth, dampened with water only, to remove
any fingerprints or to wipe off dust. Clean the grille by gentle
vacuuming or with a damp cloth.
NOTE: Do not use any cleaning products or poIishes on the cabinet or griUe.
For maximum acoustic transparency, the grille uses a lightweight
structure that needs to be handled with care for removal. To remove the
grille, gently pull on the comers to unfasten the frame from the cabinet.
To replace it, make sure to align the frame pins first and then gently
snap the frame into place. Never force the grille frame onto the cabinet.
TROUBLESHOOTING*
SYMPTOM CAUSE SOLUTION
• oooe • oeee•e eoo• eoeee • eo ee • oe • o•o o•• •ee • •••o eoe•o
ee • ee • e•e• oeo •e ee••e oooo• •o • • • •o e••e • • ••
Bass is too loud Bass reinforcement Move speakers away
in room from walls
Bass level is too high
Rotate BASS control
towards "1"(see page 7)
Bass sounds
toned
Subwoofer amplifier
has reached maximum
output
Bass level on preamlg
receiver is set too high
oeeee ••••eeoc• • o•o• • eee e• eooe ee e• oee ee •ooe• • •ooo •• • eo• • ••• ••eeo•e• • • e•e oe• •••e• ••o•e eeeoe
Turn down volume
control on receiver
or preamplifier
Set bass and treble fiat;
use controls sparingly
Distortion with Defective receiver or Repair defective
volume control preamplifier; shorted receiver or
near minimum speaker wires preamplifier ,
• • • • • e• ee ee• • • • •e e••ee e•e _•oee•o•o e•o•oe•• • o_•eee ooooe• oeoee eeo•o eeoo•_eeeoo• • •ee ee••o •oe
Distortion on music
or effects peaks
(e.g., pops or noise)
Dynamic soundtrack Tam down master
causes subwoofer volume control to
to "bottom" out lower overall range
Tone controls
are set too high
Set bass and treble fiat;
use controls sparingly
Buzz, hum, or Connecting wires Connect wires only
crackle when with power on causes when audio system
connecting wires transient signal spikes power is off
eee_eo.t•ee_•eeeeeeo•••e•eee•e•••eoe••e•o•oeo eeoeo••oe •e•eeoe.e•eeoe•e•_e_•e•e•_•e_ •
• • e• •
No sound from Power cord not Connect ac power cord;
speaker system; connected; no ac power check ac outlet
power LED not on
Blown fuse Check or replace fuse
(see page 7)
*Ifyou need further assistance, contact your local Infinity retail dealer.
8 * Compositions Overture OVTR 1 -Owner's Manual
SPECIFICATIONS - OVTR 1
PERFORMANCEDATA
DRIVE UNITS
Frequency Range:
Sensitivity:
Impedance:
Maximum Peak Output:
Amplifier Requirements:
Low Frequency:
Mid Frequency:
High Frequency:
Crossover Frequencies:
35 ~ 20,000 Hz
92 dB spl @1 m/2.83 V (anechoic conditions)
8 _ nominal.
108 dB (spl on program)
Recommended for use with amplifiers
I0 ~ I00 W (@ 8 _)
One 8" (200 ram) high-efficiency,
ultra-linear, long-throw, magneticany-
shielded woofer
'1_o 4" (100 ram) high-efficiency,
magnetically-shielded,
mid-range drivers
One 1" (25 mm) sof_ dome, high-efficiency,
neodymium magnet, magneticaUy-
shielded tweeter
300 and 3,000 Hz
AMPLIFIER
(BUILT-IN POWER AMPLIFIERFOR
LOW-Fi_QUENCY SECTION)
DIMENSIONS
(also see inside front cover)
Peak Output:
Power Supply:
Power Consumption:
Width:
Height:
Depth:
Weight:
250 VA
120 V~ 60 Hz
150 W (maximmn), 7 W (standby)
5 3/4"(146 ram)
12 V2" (318 ram)
121/2" (318 ram)
28.5 lb or 12.95 kg (each)
Comnositions Overture OVTR 1 - Owner's Manual • 9
LIMITED FIVE-YEAR WARRANTY
Who is protected by the warranty?
Your Infinity warranty protects the original retail purchaser and all subsequent owners for a period of five (5)
years (parts and labor) for all speaker components, and one (1) year (parts and labor) for all electronics, from
any failure as a result of an original manufacturing defect so long as: (1) your Infinity loudspeakers were
purchased within the fifty states of the U.S.A. or by military, pe.rsonnel from an authorized military outlet and
(2) the original dated bill of sale is presented whenever service m required during the warranty period. This
warranty does not apply to products purchased elsewhere; other purchasers should contact their local Infinity
distributor for warranty information_
What does the Infinity warranty cover?
Except as specified below, this warranty covers all defects in original materials and workmanship. The
following are not covered: damage caused by accident, misuse, abuse, neglect, product modification; damage
occurring during shipment, damage caused by failure to follow instructions in the owner's manual, including
failure to perform recommended periodic or routine maintenance; dan_age resulting from repairs_ by someone
not authorized by Infinity; claims based upon any misrepresentations by the sellers; and any Infinity proauc_
on which the serial number has been altered, defaced or removed.
Who pays for what?
During the period of this warranty, subject to the above conditions, Infinity will pay all of the labor and
material expenses to repair a warrantable defect.
How can warranty service be obtained?
In the event that your _ty loudspeaker should require servi_ce, you should first contact the Infinity dealer
from whom the product was purchased or, if this is not practical, contact Infinity directly (ATTN: Customer
Service) at 20630 Nordhoff Street, Chatsworth, CA 91311 (818) 407-0228. We may direct you to an authorized
service center for Infinity products or ask you to send them to us for repair. In either case, you will have to
present your original bill-of-sale to establish warranty coverage.
Do not send your speaker to us without prior authorization from our Customer Service Department. You are
responsible for transporting your product to either Infinity or an authorized service center and for payment of
all shipping charges; however, Infinity will pay the return shippinf! charges (in the event you return the
producttous)iftherepairsarecoveredby warranty.Ifyou experiencedifficultyin___porting yourproduct
orareinneed ofpackingmaterials,pleaseadviseus and we may be abletosuggestalternativeprocedures
and/orprovideadequatepackingmaterials.
LIMITATION OF IMPLIED WARRANTIES: All implied warranties, including fitness for a particular
purpose and merchantability are limited in duration to the length of the warranty period for your product.
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES: Infinity is not responsible for an
incidental or consequential damage of any kind. Our liability is limited to the repair or replacement, at our
option, of a defective product.
Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion
of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights and you may also have other rights which vary from state to state.
NOTE: In the event that there is a difference between this warranty and the provisions in any
advertisements, product brochure or packaging cartons, the terms of this warranty will prevail.
Infinity constantly strives to update and improve existing products, as well as create new ones. Therefore the specifications and
construction details in this and related Infinity publications are subject to change without notice.
© 1996 bafinity Systems Inc., 20630 Nordhoff Street, Chatsworth, CA 91311 USA
(818) 407-0228 • FAX (818) 709-9486
Infinity is are_ trademark of_ System_ Inc. C_mpositimm is a trademark of Infinity Systems, Ina I_, _ _, _ A_ _ _ d_ _ _ _"
PIN 331214-O01
Loading...