PLEASE SEE YOUR OWNER’S MANUAL FOR IMPORTANT SAFETY INFORMATION AND SYSTEM OPERATION LIMITATIONS.
• A cellular telephone should not
be used for any purpose while
driving so full attention may be
given to vehicle operation.
• Always wear your seat belt.
• Supplemental air bags do not
replace proper seat belt usage.
• Children 12 and under
should always ride in the
rear seat properly secured in
child restraints or seat belts
according to their age
and weight.
• Do not drink and drive.
For more information, refer to the “Safety — Seats,
seat belts and supplemental restraint system (section
1)”, the “Display screen, heater and air conditioner,
and audio system (section 4)” and the “Starting and
driving (section 5)” of your Owner’s Manual.
Page 4
Cockpit Overview
1
Page 5
Cockpit Overview
Cruise control switch
Vehicle information display and menu control switches
Combined turn signal/Low-High beam/wiper and washer switch
Shift paddles
Audio and Bluetooth® control switches
Instrument brightness control (behind steering wheel)
2
Page 6
Instrument Panel
3
Page 7
Instrument Panel
Multi-function control touch-screen / RearView Monitor display / Around View® Monitor
display (if so equipped)
Audio system
Control panel switches
• Seat heating (if so equipped)
• Hazard light switch
• Idle Stop/Start (ISS) OFF switch
• Parking Sensor system OFF switch
Climate control panel
• Heater and air conditioning (automatic)
• Front/Rear window defroster
Electronic shift lever
P (Park) button
Drive mode switch
Infiniti controller
Parking brake
External light switches
4
Page 8
Meters and Gauges
5
Page 9
Meters and Gauges
Speedometer
Fuel gauge
Vehicle information display
Shift lever indicator
Tachometer
Engine coolant temperature gauge
6
Page 10
Hood Latch
To open the hood, pull the hood release handle located
below the instrument panel
and pull the lever to the left to unlock the hood. Then insert
the support rod into the slot.
To close the hood, drop it from a height of 8-12 inches
(20-30 cm). If the hood sensor detects the hood is not
completely latched shut, the wipers will not function.
Please see your Owner’s Manual for important safety information, system
limitations, and additional operating and feature information.
Sun Visors
Pull down the sun visor to block glare from the front.
Remove the sun visor from the center mount by lifting
it slightly and swing it to the side to block glare from
the side window.
Slide the sun visor out from the mount to further
extend the visor location.
Please see your Owner’s Manual for important safety information, system
limitations, and additional operating and feature information.
. Slightly lift the hood upward
Parking Brake
To apply the parking brake, press the
electric parking brake handle located
below the instrument panel, regardless of
the ignition switch position.
To release the parking brake, pull the
electric parking brake handle toward
you while the ignition is on. The parking
brake will be automatically released when
you depress the accelerator pedal as long
as certain conditions are met, such as
having your seatbelt fastened.
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating
and feature information.
7
Page 11
Seat Adjustments
MANUAL SEAT ADJUSTMENTS (IF SO EQUIPPED)
Forward and backward adjustment:
Pull the lever
the seat forward or backward and release it to lock the seat in the
preferred position. When returning the seatback to the upright position,
always be certain it is completely secured in the latched position.
Seat angle adjustment:
Turn the hand-wheel
that your thighs are lightly supported.
Seat lifter:
Repeatedly pull up or push down the adjusting lever
seat height to the desired position.
Seatback angle:
Relieve the pressure on the seatback and turn the hand-wheel
forward or backward to adjust the seatback angle.
, located under the seat, up and hold it while sliding
forward or backward to adjust the angles so
to adjust the
LUMBAR SUPPORT
Push each side of the adjusting switch
until the desired position is achieved.
POWER SEAT ADJUSTMENTS (IF SO EQUIPPED)
Forward and backward adjustment:
Move the adjusting switch
to the desired position.
Reclining:
Move the adjusting switch
Seat lifter (if so equipped):
1. Pull up or push down the adjusting switch
height until the desired position is achieved.
2. Tilt up or down the adjusting switch
the seat until the desired position is achieved.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
, located on the door, forward or backward
forward or backward to the desired position.
to adjust the seat lumbar area
to adjust the seat
to adjust the front angle of
8
Page 12
Head Restraint Adjustment
Lane Departure Warning (LDW)
(if so equipped)
To raise the head restraint:
Pull the head restraint up.
To lower the head restraint:
Push and hold the lock knob
restraint down.
To move the head restraint forward:
Pull the head restraint toward the front of the vehicle until
it engages in one of the detents.
To move the head restraint backward:
Press and hold the button
restraint backward until it is in the desired position, then
release the button.
Make sure the head restraint is fully engaged in position
after any adjustment.
Please see your Owner’s Manual for important safety information, system
limitations, and additional operating and feature information.
and push the head
and push the head
(if so equipped)
LDW warns you if the vehicle is beginning to leave the traveling lane. If a front
wheel passes over a lane marking, LDW will warn you through a visual alert and
an intermittent vibration in the steering wheel for up to 1.5 seconds.
To enable or disable LDW:
Press the
menu
Press the or button on the steering wheel to select Lane Departure Warning and press the OK button
Press the OK button on the steering wheel to change the selection to Off,
Adaptive or Standard
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
or button on the steering wheel to select the DriveAssist
in the vehicle information display.
on the steering wheel.
.
9
Page 13
Exterior Light Operation
Left-hand parking lights switched on.
Right-hand parking lights switched on.
Side lights, license plate lights and combination meter lighting
depending on ambient light conditions/daytime light system)
switched on.
Low beam/high beam headlights. Select dipped beam or high beam
headlights using the combination switch (see hereafter).
Rear fog light switch
Front fog light switch (if so equipped)
For normal headlight operation, leave the exterior light switch in the
AUTO position.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
Wiper and Washer Switch
Turn the switch to one of the following positions to operate
the windshield wipers:
Continuous wipe, fast.
Continuous wipe, slow.
Intermittent wipe, high rain sensor (if so equipped) or speed
sensor sensitivity.
Intermittent wipe, low rain sensor (if so equipped) or speed
sensor sensitivity.
Wipers are OFF.
Press button in to the first detent for a single wipe, or in to the
second detent to operate the windshield washer and wipers.
REAR WIPER AND WASHER
Turn the rear wiper switch
to operate the rear wiper (shown in the order they appear on the
wiper switch):
Wipes with washer fluid, then returns to intermittent wiping.
Intermittent wiping.
Wiper is OFF.
Wipes with washer fluid, then returns to off.
Please see your Owner’s Manual for important safety information, system limitations,
and additional operating and feature information.
to one of the following positions
10
Page 14
USB Connection Port
Clock Set/Adjustment
Your vehicle is equipped with two USB ports, located under
the control panel, to which you can connect compatible
devices (cellular phones, iPod
audio devices, USB memory sticks, etc.).
After connecting your device through one of the USB ports,
press the MEDIA button on the control panel to select audio
playback from the device connected through the USB ports.
A second device can be connected for charging. In order
to switch to the second device for audio playback, both
devices will need to be removed and the second device
reconnected first.
Please see your INFINITI InTouch™ Owner’s Manual for important safety
information, system limitations, and additional operating and feature information.
®
devices, other compatible
11
To adjust the time and the appearance of the clock on the display:
Press the MENU button on the Infiniti controller. Then, touch the “Settings”
key on the display.
Locate and touch the “Clock” key to adjust “On-Screen Clock”, “Daylight
Savings Time”, “Clock Format (24h)” and “Time Zone”.
The time can be adjusted through “Offset Adjustment”
minutes and/or hours forward or backward. The current clock time can be set
up to a difference of 12 hours and 59 minutes.
Please see your INFINITI InTouch™ Owner’s Manual for important safety information, system limitations,
and additional operating and feature information.
by adjusting the
Page 15
Fuel-filler Door
To open the fuel-filler door,
unlock the vehicle and
gently push the front side
of the fuel-filler door.
Please see your Owner’s Manual
for important safety information,
system limitations, and additional
operating and feature information.
Opening the Liftgate
To open the liftgate, press the
button on the Intelligent
Key and then push the liftgate
release
automatically unlocks if you
are carrying the Intelligent
Key and push the liftgate
request switch
Please see your Owner’s Manual for
important safety information, system
limitations, and additional operating and feature information.
. The liftgate also
.
Electronic Shift Lever
To put the vehicle in N (Neutral):
Push the electronic shift lever forward
until you feel resistance and release the
shift lever, or pull the electronic shift lever
back until you feel resistance and release
the shift lever.
To put the vehicle in R (Reverse):
Push the electronic shift lever forward
past the point of resistance and release
the shift lever.
To put the vehicle in D (Drive):
Pull the electronic shift lever back past
the point of resistance and release the
shift lever.
To put the vehicle in P (Park):
Make sure the vehicle is completely
stopped and press the P (Park) button
If you switch the ignition off with the transmission in D (Drive) or R (Reverse), the
transmission automatically shifts into N (Neutral).
If you open the driver’s door while the vehicle is stationary or moving at a very
low-speed, the vehicle automatically switches into the P (Park) position.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
.
12
Page 16
Windows
All power windows can be operated through
the main switch on the driver’s door.
Power windows open/close.
Disable rear passenger window
operation by rear passengers.
POWER WINDOW CONVENIENCE
OPENING/CLOSING FEATURE
The vehicle can be locked/unlocked and
the power windows can be closed/opened
simultaneously from outside the vehicle
using the Intelligent Key as follows:
To lock the vehicle and close the power
windows simultaneously, touch the sensor
surface
windows are fully closed.
To unlock the vehicle and open the
windows simultaneously, press and hold
the
windows have reached the desired position.
Please see your Owner’s Manual for important safety
information, system limitations, and additional operating
and feature information.
on the door handle until the
button on the Intelligent Key until the
Idle Stop/Start (ISS)
The ISS activates when certain conditions are met to prevent
unnecessary fuel consumption, exhaust emissions and noise.
To activate the ISS system:
• Bring the vehicle to a complete stop.
To restart the engine when the ISS system is active:
• When the ISS system is active, the engine will restart as soon as you
take your foot off the brake pedal.
An ISS indicator light in the vehicle information display will inform
you of the ISS status. The system can be temporarily deactivated
by pushing the Idle Stop/Start system on/off switch
instrument panel.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
on the
13
Page 17
Intelligent Park Assist (IPA)
Voice Recognition
(if so equipped)
The Intelligent Park Assist (IPA) is an electronic parking aid. On straight and
even roads, IPA can be used to park in parallel spaces and to reverse into
perpendicular spaces.
To park using IPA:
• When the IPA detects a parking space,
the parking symbol
vehicle information display. To park in that
space, stop the vehicle and shift into the
(R) Reverse position.
• A "Start Park Assist" message will appear
in the vehicle information display. Press the
OK button on the steering wheel to enable
the IPA, or press the
the operation.
• Release the steering wheel and continue to control the accelerator,
brake and gear shift to maneuver into the parking space.
• Stop as soon as the sonar function sounds the continuous warning tone,
if not before. A message will appear in the vehicle information display if
you need to change gears.
• When the procedure is complete, a "ParkAssist switched off" message
will appear in the vehicle information display. Shift into the (P) Park
position, and apply the electric parking brake to secure the vehicle.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
will appear in the
button to cancel
SYSTEM OPERATING TIPS
• The interior of the vehicle should be as quiet as possible.
• Speak naturally. Speaking too fast, too slow, too soft, or too
loud makes voice recognition more difficult.
• Confirm that the correct voice commands are being used.
Glance at the screen to see the currently available commands.
USING THE VOICE RECOGNITION SYSTEM
• Press the
commands will appear on the screen.
• After the tone sounds, speak the command.
• To skip the voice prompt and give the command immediately,
press the
system. Speak the next command after the tone sounds.
• To cancel the command, press and hold the
the steering wheel.
Please see your INFINITI InTouch™ Owner’s Manual for important safety information,
system limitations, and additional operating and feature information.
button on the steering wheel, and a list of
button on the steering wheel to interrupt the
button on
14
Page 18
Device via Bluetooth®*
Using Bluetooth® technology, you can
connect (pair) your cellular phone with the
in-vehicle system for hands-free use of your
cellular phone.
1. Press the MENU button on the
Infiniti controller.
2. Touch the “Settings” key on the
center display.
3. Touch the “Phone/Mail” key.
4. Touch “Connect Device”.
5. Touch “Add New (X/5 Free)”.
6. If a PIN appears on the screen, operate
the Bluetooth
confirm the PIN.
For any Bluetooth® connectivity issues, reboot your cellular phone or device.
* Some jurisdictions prohibit the use of cellular telephones while driving.
Please see your INFINITI InTouch™ Owner’s Manual for important safety information, system limitations,
and additional operating and feature information.
®
device to enter/
Bluetooth® Streaming Audio*Connecting your Cellular Phone or
If you have a compatible Bluetooth® device with
streaming audio (A2DP and AVRCP profiles), you can
set up a wireless connection between your Bluetooth
device and the in-vehicle audio system, enabling you
to listen to the audio from your device through the
vehicle’s audio system.
After connecting your Bluetooth
MEDIA button
Bluetooth
®
on the control panel to switch to
Streaming Audio.
For any Bluetooth® connectivity issues, reboot your
cellular phone or device.
* Some jurisdictions prohibit the use of cellular telephones while driving.
Please see your INFINITI InTouch™ Owner’s Manual for important
safety information, system limitations, and additional operating and
feature information.
®
device, press the
®
15
Page 19
INFINITI InTouch™ Services (if so equipped)
INFINITI InTouch Services combine personalized convenience settings and
personal security features to compliment the Total Ownership Experience
more details on INFINITI InTouch Services or to enroll your vehicle, please visit
usa.infinitiintouch.com or call 1-855-444-7244.
To access INFINITI InTouch Services:
Press the MENU button on the Infiniti controller.
Select the “Information” key on the display.
Select the “InTouch Services” key on the display.
In case of an emergency,
press and release the SOS
button lid
the rearview mirror, and press
the in-vehicle telematics
SOS button
Please see your INFINITI InTouch™ Owner’s Manual for important safety information, system limitations, and additional operating and feature information.
, located above
.
®
. For
Available services include, but are not limited to:
• Automatic Collision Notification
• Alarm Notification
• Maintenance Alert
• Scheduled Maintenance Notification
• Stolen Vehicle Locator
• Emergency Call
• Roadside Assistance
• My Schedule (Google Calendar™)
• Infiniti Personal Assistance
• Destination Send-to-Vehicle
• Connected Search
• Drive Zone
• Maximum Speed Alert
• Mobile Information Service
• Valet Alert
INFINITI INTOUCH SERVICES ENROLLMENT
1. Create an INFINITI Owner Portal account.
(https://owners.infinitiusa.com/iowners/)
2. From within your INFINITI Owner Portal
account, enroll in INFINITI InTouch Services.
3. Download the INFINITI InTouch Services
companion app from the App store and
login using your INFINITI Owner Portal ID
and Password.
16
Page 20
Navigation System (if so equipped)
Use the Infiniti controller and OK button to navigate through the
center display screens.
• Press the button to return to the previous screen.
• Press the MAP/VOICE button
SETTING A ROUTE
To set a route, first ensure that the correct region is selected on the
touch-screen.
1. Press the MENU button on the Infiniti controller.
2. Touch the “Navigation” key on the display.
3. Touch the “Destination Menu” key
4. Select the preferred destination setting method.
5. Enter the address number, street name and city as prompted
by the screen.
CANCELING A ROUTE
1. Press the MENU button
2. Touch the “Navigation” key on the display.
3. Touch the “Cancel Route” key
Please see your INFINITI InTouch™ Owner’s Manual for important safety information, system
limitations, and additional operating and feature information.
to display the map.
on the display.
on the Infiniti controller.
.
17
Page 21
Cruise Control
CONVENTIONAL CRUISE CONTROL (IF SO EQUIPPED)
Cruise control maintains a constant set speed for you. The system is operational only at
speeds above 20 mph (30 km/h).
Pull the lever toward you to recall the previous speed.
Lift the lever up to the pressure point and release the lever to increase the speed by
1 mph (1.6 km/h).
Push the lever down to the pressure point and release the lever to decrease the speed by
1 mph (1.6 km/h).
Lift the lever upward beyond the pressure point and release the lever to increase the
speed to the nearest multiple of 5 mph (8 km/h).
Push the lever downward beyond the pressure point and release the lever to decrease the
speed to the nearest multiple of 5 mph (8 km/h).
To override the current stored speed with your current real speed, quickly move the stalk
up
or down .
To deactivate cruise control, push the lever away from you or push the brake pedal.
INTELLIGENT CRUISE CONTROL (ICC) (IF SO EQUIPPED)
The ICC system is designed to maintain a selected distance from the vehicle in front of you
and reduce the speed to match a slower vehicle ahead.
To increase the distance to the vehicle ahead to be maintained by the ICC system, turn the
knob
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and
feature information.
clockwise. To reduce the distance, turn the knob counterclockwise.
Cruise Control Stalk
18
Page 22
Memo
Page 23
Memo
Page 24
QR19EA 0H15U0
Printed in USA
Printing October 2018
This Quick Reference Guide is intended to provide an overview of some of
the unique features of your new vehicle. Please see your Owner’s Manual
for important safety information and system operation limitations.
Features and equipment in your vehicle may vary depending on model,
trim level, options selected, order, date of production, region or availability.
Therefore, you may find information about features or equipment that
are not included or installed on your vehicle.
All information, specifications and illustrations in this Quick Reference
Guide are those in effect at the time of printing. INFINITI reserves the
right to change specifications, performance, design or component
suppliers without notice and without obligation. From time to time,
INFINITI may update or revise this Quick Reference Guide to provide
owners with the most accurate information currently available. Please
carefully read and retain, with this Quick Reference Guide, all revision
updates sent to you by INFINITI to ensure you have access to accurate
and up-to-date information regarding your vehicle. Current versions
of vehicle Quick Reference Guides, Owner’s Manuals and any updates
can also be found in the Owner section of the INFINITI website at