A
ppNote Number
DC Shield TLE9562-3QX
About this document
Scope and purpose
This user manual describes the BLDC shield with the TLE9562-3QX. This document provides detailed
information on the board’s content, layout and use. It should be used in conjunction with the TLE9562-3QX
datasheet, which contains full technical details on the device specification and operation.
Intended audience
This document is intended for users who develop applications with the TLE956x family.
Table of contents
About this document ......................................................................................................................... 1
Table of contents .............................................................................................................................. 1
1 Introduction ............................................................................................................................ 1
2 Hardware description ............................................................................................................... 3
2.1 Hardware ................................................................................................................................................. 3
2.2 Schematic ................................................................................................................................................ 7
2.3 Layers ..................................................................................................................................................... 10
2.4 Bill of Material of the TLE9562-3QX ...................................................................................................... 12
3 Start and uIO stick programmation ...........................................................................................13
3.1 Download the Graphic User Interface for the uIO stick ....................................................................... 13
3.1.1 Download from MyICP ..................................................................................................................... 13
3.1.2 Download from the Infineon Toolbox ............................................................................................. 13
3.2 Configuration Wizard for TLE9562-3QX ................................................................................................ 14
4 Config Wizard - Control tabs .....................................................................................................15
4.1 SBC ......................................................................................................................................................... 15
4.2 Bridge Driver .......................................................................................................................................... 19
5 Revision history ......................................................................................................................21
1 Introduction
2 The TLE9652-3QX evalutaion board is intended to provide a simple and easy-to-use tool for getting
familiar with the device features and for first application tests. The evaluation board consists of a uIOstick,
a TLE9652-3QX board.
3 The uIO-stick is the interface between the PC and the application board such as the TLE9562-3QX.
The TLE9562-3QX SPI communication is emulated by the uIO-stick, which is controlled by the PC
software.
User manual Please read the Important Notice and Warnings at the end of this document V 1.0
www.infineon.com page 1 of 22 2020-07-16
DC Shield TLE9562-3QX
The board of the TLE9562-3QX has a connector for the uIO-stick, connectors for the power supply, three
4
connector for the motor output. And an active reverse battery protection with IPZ40N4S5L-2R8.
Figure 1
TLE9562-3QX evaluation Board concept
1)
The uIO stick must be ordered separately – SP001215532
Details about the uIO stick can be found hear: www.hitex.com/uIO
User manual 2 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
2 Hardware description
2.1 Hardware
The TLE9562-3QX evaluation board is designed to be compatible with the uIO-stick. The uIO-stick plugs into the
TLE9562-3QX main board via a 16-pin header, and allows an easy interface to the microcontroller via USB for
SPI communication.
Figure 2
TLE9562-3QX evaluation board
User manual 3 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
Figure 3
TLE9562-3QX evaluation board
Figure 4
TLE9562-3QX evaluation board: Jumper settings
User manual 4 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
Figure 5
TLE9562-3QX evaluation board: Jumper setttings and switches
•
Test-Mode Switch: Software Development Mode is a dedicated SBC configuration especially useful for
software development. The Watchdog is enabled in Software Development Mode as default state.
•
CRC: The SPI interface includes also 8 Bits used for Cyclic Redundancy Check (CRC) to ensure data integrity
on sent or received SPI command.
User manual 5 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
Figure 6
TLE9562-3QX evaluation board: Arduino connectors 1/2
Figure 7
TLE9562-3QX evaluation board: Arduino connectors 2/2
User manual 6 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
2.2 Schematic
Figure 8 Schematic 1/3
User manual 7 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
Figure 9 Schematic 2/3
User manual 8 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
Figure 10 Schematic 3/3
User manual 9 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
2.3 Layers
Figure 11
Top layer with overlay
User manual 10 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
Figure 12
Bottom layer with overlay
Figure 13
Inner layer - GND
<
User manual 11 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
2.4 Bill of Material of the TLE9562-3QX
Figure 14
TLE9562-3QX - Section of Bill of Material (BOM)
User manual 12 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
3 Start and uIO stick programmation
The uIO stick requires a firmware supporting the GUI (Graphic user interface)
3.1 Download the Graphic User Interface for the uIO stick
The TLE9210x gate driver setting tool can be either downloaded from Infineons’s MyICP upon access request or
from the Infinon Tool Box (not yet possible by the generation of the user manual).
3.1.1 Download from MyICP
The GUI for the Motor System IC can be downloaded upon request to Motorcontrolsolutions@infineon.com
Once the .zip file is locally extracted, start: ConfigWizard.exe (in the application subfolder) and click on the
icon for TLE9562.
Figure 15 Start of the GUI after download from MyICP
3.1.2 Download from the Infineon Toolbox
The GUI is installed the Infineon Toolbox following the steps below:
1. Go to: www.infineon.com/toolbox
2. Follow the instructions provided on the toolbox installation webpage. Also see the “Download Getting
Started Infineon Toolbox Guide” link for des additional user information
3. Launch the Infineon Toolbox on your PC:
4. Select Manage Tools
5. Search and install the tool: Config Wizard for Motor System IC
6. Start the Config Wizard for Motor System IC
7. Click on TLE9562
User manual 13 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
3.2 Configuration Wizard for TLE9562-3QX
The first utilization of the uIO stick in combination of the GUI for the TLE9562 requires the programmation of
the uIO stick:
1. Connect the uIO stick to the USB port
2. Menu Extra
3. Update uIO
4. Click Yes (refer Figure 16)
Figure 16
Updating the uIO
5. Select uIO.V222.hex and open (the valid version at the creation time of the document)
3.2
Presettings for the gate driver can be loaded:
File → Load → TLE9562_ConfigWizard_Presettings_2020_06_25_1.icwp
The charge pump is activated
-
-
The active gate control and the postcharge are activated
-
The gate driver currents for the active and freewheeling MOSFETs are pre-configured
Load TLE9562 presettings
User manual 14 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
4 Config Wizard - Control tabs
Figure 17
The two main tabs SBC, Bridge Driver
4.1 SBC
Figure 18
Connection Status/ Signaling Pin Status
User manual 15 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
Figure 19
Overview of the SBC tab
Figure 20
SBC: Control functions
User manual 16 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
Figure 21
SBC: Wake-up, PWM/Interrupt, HS1 – HS4, Timer /BUS
User manual 17 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
Figure 22
SBC Status
Figure 23
Half-Bridge (HB) Status
User manual 18 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
4.2 Bridge Driver
Figure 24
Bridge Driver: 1st Tab – General control , VDS Monitoring (Mon.)
Figure 25
Bridge Driver: 2nd Tab – Blank/ CCp time, HBMODE, Brake, TDON/ TDOFF Timing
User manual 19 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
Figure 26 Bridge Driver: 3
rd
Tab – MOSFET Drive Currents
User manual 20 of 22 V 1.0
2020-07-16
DC Shield TLE9562-3QX
5 Revision history
Document
Date of release Description of changes
version
V 1.0 2020-07-16 Initial version
User manual 21 of 22 V 1.0
2020-07-16
e
e
n
s
n
n
y
n
y
e
n
Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
Edition 2020-07-16
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2020 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about this
document?
Email: erratum@infineon.com
Document reference
AppNote Number
IMPORTANT NOTICE
The information contained in this application note is
given as a hint for the implementation of the product
only and shall in no event be regarded as a
description or warranty of a certain functionality,
condition or quality of the product. Before
implementation of the product, the recipient of this
application note must verify any function and other
technical information given herein in the real
application. Infineon Technologies hereby disclaims
any and all warranties and liabilities of any kind
(including without limitation warranties of noninfringement of intellectual property rights of any
third party) with respect to any and all information
given in this application note.
The data contained in this document is exclusively
intended for technically trained staff. It is the
responsibility of customer’s technical departments
to evaluate the suitability of the product for the
intended application and the completeness of the
product information given in this document with
respect to such application.
For further information on the product, technology
delivery terms and conditions and prices pleas
contact your nearest Infineon Technologies offic
(www.infineon.com).
WARNINGS
Due to technical requirements products may contai
dangerous substances. For information on the type
in question please contact your nearest Infineo
Technologies office.
Except as otherwise explicitly approved by Infineo
Technologies in a written document signed b
authorized representatives of Infineo
Technologies, Infineon Technologies’ products ma
not be used in any applications where a failure of th
product or any consequences of the use thereof ca
reasonably be expected to result in personal injury.
Loading...