Inferno SRPH67, SRPH69 User Manual
OUTDOOR
GB
TM
This IM applies to both SRPH67 & SRPH69.
Keep the instructions
for future reference.
WARNING
GB
1. For use outdoors or in amply ventilated
areas.
2. An amply ventilated area must have a mini-
mum of 25% of the surface area open.
3. The surface area is the sum of the walls
surface.
4. This appliance is not fitted with “Atmo-
sphere sensing device”.
WARNING: The use of this appliance in
enclosed areas can be dangerous and is
PROHIBITED.
WARNING: Read the instructions before
installation and use.
Warning: This appliance must be installed
and the gas cylinder stored in accordance
with the regulations in force.
Warning: Use only the type of gas and the
type of cylinder specified by the manufacturer.
Warning: Do not obstruct the ventilation
holes of the cylinder housing.
Warning: In case of violent wind particular
attention must be taken against tilting of the
appliance.
Warning: Do not move the appliance when in
operation.
Warning: Shut off the valve at the gas cylinder or the regulator before moving the appliance.
Warning: The
tubing or the flexible hose
must be changed within the prescribed intervals.
Warning: The heater can’t be used when the
heat exchange tube is retracted into cylinder
compartment.
Warning: Do NOT keep the heater fully
extended and the heat exchange tube must be
lowered down to position during transportation!
2
Technical data
GB
Country Category Nominal heat
input(Hs)
FI
IT
NO
SK
LU
DE
DK
FR
LT
SE
RO
BG
MT
I
3B/P(50)
I
3B/P(30)
I
3+(28-30/37)
11kW 800 g/h(G30)
11kW 800 g/h(G30) 1.67mm
11kW
AT CH
SK
BE CY
EE
HU
NL
SI
HR TR
IS
BE CH CY
CZ ES FR
GB GR I E
Gas
consumption
800 g/h (G30) 1.67mm
Injector
diameter(Ø)
1.39mm G30 Butane and
Gas & Pressure
G31 Propane at
50mbar
G30 Butane and
G31 Propane at
30mbar
G30 Butane at
28-30mbar and
G31 Propane at
IT L T LU
LV PT SK
SI
PL
I
3B/P(37)
11kW
Manufacturer:
SHINERICH INDUSTRIAL LIMITED
Address: 8/F, Noble Center, 1006 Fuzhong
3rd Road, Futian District, Shenzhen,GD
518026, CHINA
Phone: +86 - 755 - 8826 7676
800 g/h(G30)
For questions, replacement parts, service
help, or other assistance, please call
Distributor name
Address:
Email:
1.67mm
37mbar
G30 Butane and
G31 Propane at
37mbar
3
GB
Number of people required to assemble
One people
Time to assemble
10 minutes
Assembly instructions
Find a large, clean area to assemble your
appliance. Please refer to the parts list and
assembly diagram as necessary.
Please use protective gloves when assembling this product.
To avoid losing any small component or
hardware, assemble your product on a hard
level surface that does not have cracks or
openings.
To avoid damage to soft floor or carpet, do
not assemble or move the appliance on soft
floor or carpet.
Follow all steps in order to properly
assemble your product.
Make sure all the plastic protection rip off
before assembling.
Do not force parts together as this can result
in personal injury or damage to the product.
When applicable, tighten all hardware connections by hand first, once the step is completed, go back and full tighten all hardware.
Caution: Whilst every effort has made in
manufacture of your appliance to remove
any sharp edge, you should handle all components with care to avoid accidental injury.
4
Further information
GB
Important Notes:
LPG cylinder not provided. The appliance is
designed to operate with a cylinder of size Ø
31.8 x 58 cm.
This appliance requires a 15 kg butane LPG
cylinder or a 13 kg propane LPG cylinder.
Gas regulator should be the correct one and
be set according to specific gas category
(see Technical data on page 3).
Gas regulator should be approved according
to EN 12864 with proper capacity (g/h), pressure, working temperature and inlet + outlet
connection for the country of destination.
The regulator illustrated on the manual is for
United Kingdom, the regulator in your country
maybe different with the one on the illustration.
Flexible gas rubber pipe should be approved
according to EN 1763-1 with proper inner Ø
to match pipe holders of gas circuit and gas
regulator, pressure and working temperature.
The length of the hose is 0.41 m and it
should not exceed 0.7 m. The hose shall be
readily visible across its entire length for
inspection after installation.
Connect LP Gas cylinder
Before connecting, be sure that there is no
debris caught in the head of the LP tank,
head of the regulator valve or in the head
of the burner and burner ports.
Connect gas line to tank
by turning knob
clockwise until it stops, make sure that the
tube is not subject to twisting.
After connecting to gas cylinder, a leak testing is necessary.
Disconnect LP Gas cylinder
Before disconnecting make sure the LP gas
tank valve in “CLOSED”. Disconnect gas line
from LP gas cylinder by turning knob
counterclockwise until it is loose.
For storage and cylinder exchange, disconnect hose at the cylinder only, DO NOT
disconnect hose from appliance.
To change the gas cylinder in an amply ventilated area, away from any ignition source
(candle, cigarettes, other flame producing
appliances…).
Danger:
You must have the proper regulator and
cylinder in order for the appliance to operate
safely and efficiently. Use of an incorrect or
faulty regulator is dangerous and will invalidate any warranty.
5
Loading...