Page 1
PH T- SER IES PANHE A D
OPERATING INSTRUCTIONS
Thank you for making Induro your choice for
professional photographic gear. Your Induro gear
is manufactured to provide years of dependable
service. In order to obtain optimum satisfaction
and performance we suggest that you carefully
read these instructions and provide them to
anyone who may also use your Induro gear.
Specifications and design are subject to change without notice.
All tradenames, logos, and brand refer ences are the re spective trademarks of their owners.
INDURO Camera Support Gear | 75 Virginia Road, Nor th White Plains, NY 10603 | T 914-347-3300 | F 914-347-3309 | info@indurogear.com | indurogear.com
Page 2
360°
Locking Collar Nut
Camera Screw
Bubble Level
Locking Collar Nut
Front/Rear
Tilt Control/Lock Handle
1
Quick Release Plate
SETUP
Head Mounting
Tilt Control/Lock Handle
Side to Side
Install by screwing the head clockwise onto the
3/8" Mounting Thread of the Top Plate of the
Tripod or Monopod. Once it is hand tight, secure
by fully tightening the Head Locking Screw(s) (on
selec t models) from below..
OPERATION
Three-way positioning of camera and lens
movement is directly controllable on the
PHT-Series Panheads. Two comfortable foldable
Plate Locking Lever
Security Locking Lever
Pan Control/Lock Knob
Base
2
3
54
Handles provide both movement and locking of
front to rear Tilt, and side to side Tilt. Plus,
a separate Locking Knob permits the entire
Head assembly to move freely within a 360°
rotational adjustment.
Quick Release Plate
The PHT-Series Panheads incorporate a Quick
Release Plate system. It offers a quick method of
mounting or releasing a Camera or Equipment
from the Head. It’s important that the correct
Quick Release Plate be used along with the
proper mounting screw (1/4–20 is included as
the standard size but spare 1/4–20 and 3/8 plates
are available as accessories). Extra Plates are
recommended as you can screw one to each
Camer a or Lens for even greater convenience
when rapidly mounting and dismounting gear.
Quick Release Locking Lever (FIGURES 1 & 2)
When used properly, the patented Dual Lock
Quick Release system offers two levels of
security for your gear. To remove the Quick
Release Plate, squeeze both the Plate Locking
Lever and the Security Locking Lever and pull
the larger Locking Lever out. The Quick Release
Plate will disengage allowing it to be removed.
To reconnect the Quick Release Plate, insert the
angled part of the Plate into the groove on the
opposite side of the Locking Levers and press
down flat. The Locking Levers will automatically
engage the locking system and will return to
the safety lock position. Press the Plate Locking
Lever in firmly to secure.
Pan Control (FIGURE 3)
Horizontal rotation or Panning can be easily
accomplished by first loosening the Pan Lock
and then rotating Head on Platform. Once in
position tighten the Pan Lock securely.
NOTE: Do not over tighten the Pan Lock as this
could damage the locking mechanism.
Tilt Control (FIGUR E 4)
Front to Rear Angle or Tilt adjustments can be
easily accomplished by first loosening the Front
to Rear Tilt Control Handle (be sure to hold on
firmly to balance weight of the camera). Position
as required and then tighten Handle securely.
The same Control and Lock are available on
the other axis for Side to Side Angle or Tilt
adjustments by using the Side to Side Tilt Control
Handle. The Bubble Level can be viewed while
making adjustments.
NOTE: Do not over tighten the Tilt Control Locks
as this could damage the locking mechanism.
FOR ADDITIONAL CONTROL: Depending on
your requirements you may find it convenient
to reorient the camera or lens 90° on the Quick
Release Plate and remount so that the Tilt
Controls give you different positioning support.
Folding Tilt Control Handles (FIGURE 5)
Both Tilt Control Handles can easily fold down
along the sides of the PHT Head to make packing
and transport much more convenient. To prepare
for transport (without a camera mounted), firmly
hold the Handle and rotate the Locking Collar Nut
counter-clockwise until you can slide it back on
the shaft exposing the joint and allowing it to bend.
Reverse the procedure to secure the Handle for
normal operation.
USER NOTICE
c Do not exceed the maximum specified load
capacity (see specifications on the package label
or visit ww w.InduroGear.com).
c Always ensure that all Panhead locks are tightly
engaged before mounting any gear.
c Always clean and dry any Panhead after it has been
exposed to wet, dusty, sandy or salty conditions.
Your Panhead is not recommended for use in salt
water. If required, clean Panhead using a mild soap
solution applied with a soft cloth, rinse with fresh
water and dry with soft towel. Remove any dust,
dirt or sand from all locks and all mov ing part s.
c Do not leave any Panhead in the sun for prolonged
periods and avoid high temperature exposure.
c Avoid leaving any Tripod or Monopod unattended
in areas where people could trip over the gear and
get hurt.
c Remove camera, lens, and all gear from any
Tripod or Monopod when transporting.
c For your safety, don’t let your Induro gear come in
contact with any elec trical power source.
Loading...