Page 1
3D-SERIES 3- WAY PANHEAD
OPER AtINg INS t Ruc t IONS
Thank you for making Induro your choice for
professional photographic gear. Your Induro gear
is manufactured to provide years of dependable
service. In order to obtain optimum satisfaction
and performance we suggest that you carefully
read these instructions and provide them to
anyone who may also use your Induro gear.
Page 2
Camera Screw
Bubble Level
Front/Rear Tilt Lock
Quick Release Plate
Horizontal Tilt Lock
Plate Locking Lever
Security Locking Lever
Pan Lock
Base
USER NOTICE
Do not exceed the maximum specied c
load capacity (see Specication chart)
c
Always ensure that leg and head locks
are tightly engaged before mounting a
camera on the tripod
c
Do not use the tripod below
temperatures of -4°F or above +158°F
(-20°C / +70°C)
c
Always clean and dry the tripod after it
has been exposed to wet, dusty, sandy
or salty conditions. Your tripod is not
recommended for use in salt water.
If required clean tripod using a mild
soap solution applied with a soft cloth
and follow by wiping down with fresh
water. Remove any dust, dirt or sand
from all leg locks, leg lock levers,
leg sections and all moving parts.
c
Do not leave the product in the sun
for prolonged periods and avoid high
temperature exposure
c
Avoid leaving the tripod unattended in
areas where people could trip over the
tripod and get hurt
c
Remove camera, lens, and all gear
from the tripod when transporting
the tripod
c
For your safety, don’t let your Induro
tripod come in contact with any
electrical power source
Page 3
Install by screwing the
1
head clockwise on to the
3/8 thread mounting thread
of tripod plate. Once it is
hand tight secure by fully
tightening the three head
locking screws from below.
A patented dual lock
2
quick release system
when used properly offers
two levels of security for
your gear. To remove the
quick release plate, squeeze
both levers and pull the
larger plate locking lever
out. The quick release plate
will disengage so it can
be removed.
To reconnect the quick
3
release plate, insert the
angled part of the plate into
the groove on the opposite
side of the locking lever and
press down at. The locking
levers will automatically
engage the locking system
and the locking levers will
return to the safety lock
position. Press the plate
locking lever in rmly
to secure.
Horizontal rotation or
4
panning can be easily
accomplished by rst
loosening the pan lock
and then rotating head on
platform. Once in position
tighten the pan lock securely.
Front to rear angle or
5
tilt adjustments can
be easily accomplished
by rst loosening the tilt
lock (be sure to hold on
rmly to balance weight of
the camera). Position as
required and then tighten
handle securely. You have
the same control and lock
available on the other axis
for horizontal angle or
tilt adjustments.
Depending on your
6
requirements you may
nd it convenient to reorient
the camera or lens 90 degrees
on the quick release and
remount so that the tilt
controls give you different
positioning support.
Page 4
WEIGHT LOAD
MATCHING
TRIPODS
RANGE
FRONT HORIZONTAL LB KG LB KG
CAT # MODEL # CAMERA MOUNT TILT RANGE PANNING
3-Way Panhead 3D-Series
483-001 3D-S-01 QR-3D-01-14S* +65°/-65° +90°/-25° 360° 0 & 1 1.1 0.5 11.0 5.0
483-002 3D-M-23 QR-3D-23-38M** +90°/-30° +90°/-30° 360° 2 & 3 1.8 0.8 17.6 8.0
483-003 3D-L-34 QR-3D-34-38L** +90°/-25° +90°/-35° 360° 3 & 4 2 .1 1.0 26.5 12.0
SPECIFICATIONS
* 1/4-20 Quick Release Plate; * * 1/4-20 & 3/8-16 Quick Release Plates
INDURO Camera Support Gear | 8 Westchester Plaza, Elmsford, NY 10523 | T 914-347-3300 | F 914-347-3309 | info@indurogear.com | indurogear.com
Loading...