Page 1
3D-SERIES 3-WAY PANHEAD
OPER AtINg INSt RuctIONS
Thank you for making Induro your choice for
professional photographic gear. Your Induro gear
is manufactured to provide years of dependable
service. In order to obtain optimum satisfaction
and performance we suggest that you carefully
read these instructions and provide them to
anyone who may also use your Induro gear.
Page 2
USER NOTICE
Quick Release Plate
Horizontal Tilt Lock
Plate Locking Lever
Pan Lock
Base
Camera Screw
Bubble Level
Front/Rear Tilt Lock
Security Locking Lever
Do not exceed the maximum specied c
load capacity (see Specication chart)
Always ensure that leg and head locks
c
are tightly engaged before mounting a
camera on the tripod
Do not use the tripod below
c
temperatures of -4°F or above +158°F
(-20°C / +70°C)
Always clean and dry the tripod after it
c
has been exposed to wet, dusty, sandy
or salty conditions. Your tripod is not
recommended for use in salt water.
If required clean tripod using a mild
soap solution applied with a soft cloth
and follow by wiping down with fresh
water. Remove any dust, dirt or sand
from all leg locks, leg lock levers,
leg sections and all moving parts.
Do not leave the product in the sun
c
for prolonged periods and avoid high
temperature exposure
Avoid leaving the tripod unattended in
c
areas where people could trip over the
tripod and get hurt
Remove camera, lens, and all gear
c
from the tripod when transporting
the tripod
For your safety, don’t let your Induro
c
tripod come in contact with any
electrical power source
Page 3
1
Install by screwing the
head clockwise on to the
3/8 thread mounting thread
of tripod plate. Once it is
hand tight secure by fully
tightening the three head
locking screws from below.
2
A patented dual lock
quick release system
when used properly offers
two levels of security for
your gear. To remove the
quick release plate, squeeze
both levers and pull the
larger plate locking lever
out. The quick release plate
will disengage so it can
be removed.
3
To reconnect the quick
release plate, insert the
angled part of the plate into
the groove on the opposite
side of the locking lever and
press down at. The locking
levers will automatically
engage the locking system
and the locking levers will
return to the safety lock
position. Press the plate
locking lever in rmly
to secure.
4
Horizontal rotation or
panning can be easily
accomplished by rst
loosening the pan lock
and then rotating head on
platform. Once in position
tighten the pan lock securely.
5
Front to rear angle or
tilt adjustments can
be easily accomplished
by rst loosening the tilt
lock (be sure to hold on
rmly to balance weight of
the camera). Position as
required and then tighten
handle securely. You have
the same control and lock
available on the other axis
for horizontal angle or
tilt adjustments.
6
Depending on your
requirements you may
nd it convenient to reorient
the camera or lens 90 degrees
on the quick release and
remount so that the tilt
controls give you different
positioning support.
Page 4
SPECIFICATIONS
CAT # MODEL # CAMERA MOUNT TILT RANGE PANNING
RANGE
MATCHING
TRIPODS
WEIGHT LOAD
FRONT HORIZONTAL LB KG LB KG
3-Way Panhead 3D-Series
483-001 3D-S-01 QR-3D-01-14S* +65°/-65° +90°/-25° 360° 0 & 1 1.1 0.5 11.0 5.0
483-002 3D-M-23 QR-3D-23-38M** +90°/-30° +90°/-30° 360° 2 & 3 1.8 0.8 17.6 8.0
483-003 3D-L-34 QR-3D-34-38L** +90°/-25° +90°/-35° 360° 3 & 4 2.1 1.0 26.5 12.0
* 1/4-20 Quick Release Plate; * * 1/4-20 & 3/8-16 Quick Release Plates
INDURO Camera Support Gear | 8 Westchester Plaza, Elmsford, NY 10523 | T 914-347-3300 | F 914-347-3309 | info@indurogear.com | indurogear.com
Loading...