INDESIT TAN 5 FNF DNX (TK) User Manual
Operating Instructions
2-DOOR FRIDGE
GB F
English, 1
Français, 13
TK
Türkçe, 37
TAN 5 FNF DNX
E
Espanol, 25
Contents
GB
Installation, 2
Positioning and connection
Reversible doors
Description of the appliance, 3-4
Control panel
Overall view
Start-up and use, 5-6-7
Starting the appliance
Using the display
Chiller system
Using the refrigerator to its full potential
Using the freezer to its full potential
Maintenance and care, 8
Switching the appliance off
Cleaning the appliance
Avoiding mould and unpleasant odours
Replacing the light bulb
Precautions and tips, 9
General safety
Disposal
Respecting and conserving the environment
Troubleshooting, 10
Assistance, 11
Installation
! Before placing your new appliance into operation please
GB
read these operating instructions carefully. They contain
important information for safe use, for installation and for care
of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
Positioning and connection
Positioning
1. Place the appliance in a well-ventilated humidity-free room.
2. Do not obstruct the rear fan grills. The compressor and
condenser give off heat and require good ventilation to
operate correctly and save energy.
3. Leave a space of at least 10 cm between the top part of
the appliance and any furniture above it, and at least 5 cm
between the sides and any furniture/side walls.
4. Ensure the appliance is away from any sources of heat
(direct sunlight, electric stove, etc.).
5. In order to maintain the correct distance between the
appliance and the wall behind it, fit the spacers supplied in
the installation kit, following the instructions provided.
Levelling
1. Install the appliance on a level and rigid floor.
2. If the floor is not perfectly horizontal, adjust the refrigerator
by tightening or loosening the rear feet.
Reversible doors
If it is necessary to change the direction in which the
doors open, please contact the Technical Assistance
Centre.
Electrical connections
After the appliance has been transported, carefully place it
vertically and wait at least 3 hours before connecting it to the
electricity mains. Before inserting the plug into the electrical
socket ensure the following:
The appliance is earthed and the plug is compliant with the
law.
The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located on
the bottom left side of the fridge (e.g. 150 W).
The voltage must be in the range between the values
indicated on the data plate located on the bottom left side
(e.g. 220-240V).
The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it (see Assistance). Do not
use extension cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
! The manufacturer declines any liability should these
safety measures not be observed.
2
Description
of the appliance
Control panel
FREEZER
Temperature
Adjustment
GB
ALARMS
BOTTLE CHILL
FREEZER
status bar
REFRIGERATOR
status bar
CHILD LOCK
REFRIGERATOR
Temperature
Adjustment
ECO
ON/OFF
It is possible to switch the whole product (both the
refrigerator and freezer compartments) on by pressing this
button. The red LED indicates that the product is switched
off, while the green LED shows that it is operating. To
switch the product off, press and hold the ON/OFF button
for at least two seconds.
ECO
This is used to activate and deactivate the ECO function
(the optimal temperature for energy saving levels). When
activated, the AUTO LED and the ECO LED illuminate
simultaneously.
ALARMS
This controls all the alarm signals connected to product
operation.
CHILD LOCK
Activates or deactivates the control panel button lock in order
to avoid the risk of the various functions being activated
accidentally by children.
REFRIGERATOR - and +Temperature Adjustment
Enable the temperature setting of the refrigerator to be
modified, with the relative confirmation of the temperature
selected shown on the display. It is also possible to use
these buttons to deactivate the refrigerator compartment
only.
ON/OFF
SUPER
FREEZE
SUPER
COOL
HOLIDAY
REFRIGERATOR status bar
Indicates the set temperature relating to the refrigerator
compartment or shows that it has been deactivated (in this
case the status bar is disabled).
FREEZER status bar
Shows the set temperature relating to the freezer
compartment.
SUPER COOL
Activates or deactivates the SUPER COOL function (rapid
cooling). The SUPER COOL LED illuminates.
SUPER FREEZE
Activates or deactivates the SUPER FREEZE function (rapid
freezing). The SUPER FREEZE LED illuminates.
HOLIDAY
Activates or deactivates the HOLIDAY function (the AUTO
LED and HOLIDAY LED illuminates).
BOTTLE CHILL
Activates or deactivates the BOTTLE CHILL function (It
reduces the temperature of the freezer for the period of
time required to cool a bottle.). the BOTTLE CHILL
illuminates)
FREEZER - and + Temperature Adjustment
Enable the temperature setting of the freezer to be
modified, with the relative confirmation of the temperature
selected shown on the display.
3
Description of the
appliance
Overall view
GB
The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not directly
represent the appliance purchased. For more complex features, consult the following pages.
ICE DEVICE
FAST FREEZER
compartment
Removable
FREEZER and
STORAGE
compartment
multipurpose
SHELVES
COOL BOX
Compartment
LIFT SHELF
SHELVES
WINE RACK
FRUIT and
VEGETABLE
bin
Removable lidded
shelf with EGG TRAY
BEVERAGE CAN
shelves
Removable
multipurpose
SHELVES
BOTTLE shelf
Levelling FEET
Varies by number and/or position.
4
Start-up and use
Starting the appliance
! After transportation of the appliance, carefully place it in an
upright position and wait at least 3 hours before connecting
it to the electricity mains, to make sure it operates as it
should.
Clean the inside of the refrigerator well using warm water
and bicarbonate of soda before placing food inside it.
The appliance comes with a motor protection control
system which makes the compressor start
approximately 8 minutes after being switched on. The
compressor also starts each time the power supply is
cut off whether voluntarily or involuntarily (blackout).
Freezer Compartment
When the product is switched on the freezer compartment is
set to its default value of -18°C. We recommend that the
SUPER FREEZE function is set (the freezer status bar
continues to display the set value) in order to accelerate the
cooling process of the compartment; when the inside of the
compartment has reached its optimal temperature the
function will be deactivated and the food may be placed
inside.
Refrigerator Compartment
When the appliance is switched on the refrigerator
compartment is set to its default value of +5°C. We
recommend that the SUPER COOL function is set (the
refrigerator status bar continues to display the set value) in
order to accelerate the cooling process of the compartment.
After a few hours it will be cool enough for food to be placed
inside.
Navigating the display
Setting the temperatures:
If the product is switched on, the refrigerator and freezer
status bars will indicate the temperatures set at that
-
moment. To change them, simply press the
corresponding to the compartment for which you wish to
change the set temperature. More specifically, each time one
of the buttons is pressed the temperature is increased or
decreased by 1°, and the level of cold is adjusted
accordingly.The temperature values that may be selected for
the refrigerator compartment are +12°C, +7°C, +6°C, +5°C,
+4°C, +3°C and +2°C, while the values that may be set for
the freezer are -18°C, -19°C, -120°C, -21°C, -22°C, -24°C
and -26°C.
and + buttons
The temperatures are automatically set to +5°C for the
refrigerator compartment and -18°C for the freezer
compartment (these are standard food storage values.
When the ECO function is active, the appliance
automatically adjusts the temperatures according to the
conditions inside and outside the refrigerator; the operation
of this function is signalled by the text AUTO.
Whenever it is necessary to activate the ECO function at
temperatures that are different to the standard storage
values, the ECO button must be pressed as soon as the
function is activated and held down while the new
-
temperatures are set using the
these conditions, the temperatures may be set to 4°C, 5°C
and 6°C for the refrigerator compartment and -18°C, -19°C
and -20°C for the freezer compartment.
When the HOLIDAY function is active the temperature may
not be adjusted, however the appliance adjusts itself
automatically so that the optimal settings for the situation are
used: +12°C for the refrigerator compartment and -18°C for
the freezer compartment. This function is indicated by the
text.
To activate and deactivate the functions simply press the
relevant button and the function status will be signalled by
the corresponding LED switching on or off.
Several functions (SUPER COOL, SUPER FREEZE,
BOTTLE CHILL
(HOLIDAY,...); remember that there is a pre-set order of
priority which will help you to use the product in the best
possible way.
When the BOTTLE CHILL function has finished, press the
BOTTLE CHILL button to stop the corresponding LED from
flashing and to silence the sound signal. This flashing and
sound signal indicates that the function is complete and that
the bottle should be removed from the freezer compartment.
Child Lock
In order to activate the Child Lock function, the Child Lock
button must be pressed for 2 seconds; the activation of the
button lock is confirmed by a short beep and the illumination
of the corresponding LED.
To deactivate the function, press the Child Lock button for 2
seconds; deactivation will be confirmed by a short beep and
by the corresponding LED switching off.
!
The FREEZER status bar is also used to indicate an
, ECO) are incompatible with others
and + buttons. Under
unusual temperature increase in the freezer
compartment (see Troubleshooting).
GB
5
Chiller system
GB
No Frost
The No Frost system circulates cold air continuously to
collect humidity and prevent ice and frost formation. The
system maintains an optimal humidity level in the
compartment, preserving the original quality of the food,
preventing the food from sticking together and making
defrosting a thing of the past.
! Do not block the aeration cells by placing food or
containers in direct contact with the refrigerating back
panel.
! Close bottles and wrap food tightly.
Using the refrigerator to its full potential
Adjust the temperature using the display.
SHELVES: with or without grill.
1
2
Lift shelf
The lift shelf is a special shelf which optimises the space
inside the refrigerator compartment. It may be placed in
either of the two positions shown in the diagram. The most
appropriate operating configuration may be achieved
easily, thanks to special guide rails which offer balanced
upward or downward movement.
Due to the special guides the
shelves are removable and the
height is adjustable (see diagram),
allowing easy storage of large
containers and food. Height can
be adjusted without complete
removal of the shelf.
Activate the SUPER COOL function to lower the
temperature quickly, for example, when you place a
large number of new food items inside a fridge and the
internal temperature rises slightly. This function quickly
cools the groceries by temporarily reducing the
temperature until it reaches the ideal level.
Place only cold or lukewarm foods in the compartment,
never hot foods (see Precautions and tips).
Remember that cooked foods do not last longer than
raw foods.
Do not store liquids in open containers: they will
increase the level of humidity in the refrigerator and
cause condensation to form.
A
! hold the shelf with both hands and perform an even
upward or downward movement.
If you wish to place the shelf in position A, simply lift it and
it will lock into place automatically. To restore its original
position (B), simply lift the shelf slightly then push it
downwards into the desired position.
COOL BOX: for fresh meat and
fish. Due to the compartments low
temperature (the coldest in the
refrigerator) and to the clear door
that provides protection against
oxidation and blackening, food can
be stored for even up to one week.
It can also be used for cold
meals.
B
BEVERAGE CAN shelves.
The can rack on the inner door
allows you to store not only cans,
but also yoghurt, butter and other
containers, according to your
requirements.
6
Using the freezer to its full potential
Adjust the temperature using the display.
To freeze (if the freezer is already operating):
- for small quantities which are less than those indicated
on the data plate, press the rapid freezing SUPER
FREEZE button (corresponding indicator light illuminates),
insert the food and close the door. The function is disabled
automatically after 24 hours or when optimal temperatures
have been reached (indicator light goes out);
- for large quantities which are greater than the
maximum load indicated on the data plate, hold down
the rapid freezing SUPER FREEZE button until the
corresponding indicator light begins to flash. After 24 hours
the indicator light stops flashing and remains on constantly.
Place the food inside the freezer and close the door. After
another 24 hours, the function will be disabled automatically
(indicator light goes out).
Do not re-freeze food that is defrosting or that has
already been defrosted. These foods must be cooked
and eaten (within 24 hours).
Fresh food that needs to be frozen must not come into
contact with food that has already been defrosted.
ICE DEVICE
After pouring water in the special ice cups, place them in
their places in the ice device. After about 2 hours, the ice
cubes will be ready. In order to get the ice cubes, it will be
sufficient to turn the two buttons to the right. The ice cubes
will fall in to the tray below, ready to be used.
GB
Do not place glass bottles which contain liquids, and
which are corked or hermetically sealed in the freezer
because they could break.
The maximum quantity of food that may be frozen daily is
indicated on the plate containing the technical properties
located on the bottom left side of the refrigerator
compartment (for example: Kg/24h: 4).
! Do not open the door during freezing.
! If there is a power cut or malfunction, do not open the
freezer door. This will help maintain the temperature inside
the freezer, ensuring that foods are conserved for at least 9 14 hours.
! To avoid blocking the air circulation inside the freezer, it is
advisable not to obstruct the ventilation holes with food or
containers.
7
Maintenance and care
Switching the appliance off
GB
During cleaning and maintenance it is necessary to
disconnect the appliance from the electricity supply:
1. Hold the ON/OFF button down for more than two
seconds until OFF appears on both indicator displays
(refrigerator and freezer).
2. Pull the plug out of the socket.
! If this procedure is not followed, the alarm may sound.
This alarm does not indicate a malfunction. To restore
normal operation, hold the ON/OFF button down for more
than two seconds. To disconnect the appliance, follow
points 1 and 2 above.
Cleaning the appliance
The external and internal parts and the rubber seals may
be cleaned using a sponge that has been soaked in
lukewarm water and bicarbonate of soda or neutral
soap. Do not use solvents, abrasive products, bleach or
ammonia.
The removable accessories may be soaked in warm
soapy water or dishwashing liquid. Rinse and dry them
carefully.
The back of the appliance may collect dust. This can be
removed by carefully using the hose of a vacuum cleaner
set on medium power. The appliance must be switched
off and the plug disconnected from the electricity mains
before it is cleaned.
Replacing the light bulb
To replace the light bulb in
the refrigerator
compartment, pull out the
plug from the electrical
socket. Follow the
instructions below.
Access the light bulb by
removing the cover as
indicated in the diagram.
Replace it with a similar
light bulb within the power
range indicated on the cover (10W).
To replace the light bulb in
A
B
power range indicated on the cover (10W or 15W).
the freezer compartment,
pull out the plug from the
electrical socket. Follow
the instructions below.
Access the light bulb (A) by
unscrewing the fixing
screw (B) which is located
at the back of the
lampcover, as shown (see
diagram). Replace it with a
similar light bulb within the
Avoiding mould and unpleasant odours
The appliance is manufactured with hygienic, odour free
materials. Food should be wrapped well and containers
closed properly in order to maintain this hygiene. This
will also prevent the formation of stains.
If you wish to switch the appliance off for an extended
period of time, clean the inside and leave the doors
open.
8
Precautions and tips
! The appliance was designed and manufactured in
compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
This appliance complies with the following
Community Directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and
subsequent amendments;
-89/336/EEC of 03.05.89 (Electromagnetic
Compatibility) and subsequent amendments;
- 2002/96/CE.
General safety
The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial
use.
The appliance must be used to store and freeze food
products by adults only and according to the
instructions in this manual.
The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
Do not touch the appliance with bare feet or with wet or
moist hands and feet.
Do not touch the internal cooling elements:
this could cause skin abrasions or frost/freezer burns.
Disposal
GB
Observe local environmental standards when disposing
packaging material for recycling purposes.
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed of
in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials they
contain and reduce the impact on human health and the
environment. The crossed out wheeled bin symbol on
the product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or retailer
for information concerning the correct disposal of their
old appliance.
Respecting and conserving the
environment
Install the appliance in a fresh and well-ventilated room.
Ensure that it is protected from direct sunlight and do
not place it near heat sources.
Try to avoid keeping the door open for long periods or
opening the door too frequently in order to conserve
energy.
When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
Always switch the appliance off and disconnect it from
the electrical supply before cleaning it or carrying out
maintenance work. It is NOT sufficient to hold the ON/
OFF button down for more than two seconds to
eliminate all electrical contact.
In the case of a malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may cause
injury or further malfunctioning of the appliance.
Do not use any sharp or pointed utensils or electrical
equipment - other than the type recommended by the
manufacturer - inside the frozen food storage
compartments.
Do not put ice cubes taken directly from the freezer into
your mouth.
Do not allow children to tamper with the controls or play
with the appliance. Under no circumstance should they
be allowed to sit on the bins or to hang from the door.
Keep packaging material out of the reach of children! It
can become a choking or suffocation hazard.
Do not fill the appliance with too much food: cold air
must circulate freely for food to be preserved properly. If
circulation is impeded, the compressor will work
continuously.
Do not place hot food directly into the refrigerator. The
internal temperature will increase and force the
compressor to work harder and will consume more
energy.
Defrost the appliance if ice forms (see Maintenance). A
thick layer of ice makes cold transference to food
products more difficult and results in increased energy
consumption.
Regularly check the door seals and wipe clean to ensure
they are free of debris and to prevent cold air from
escaping (see Maintenance).
9
Troubleshooting
If the appliance does not work, before calling for Assistance (see Assistance), check for a solution from the following list.
GB
Malfunctions:
The display is completely switched off.
The motor does not start.
The display is on but it is dim.
The alarm sounds, the ALARM LED
lights up and the refrigerator
compartment light flashes.
The alarm sounds, the ALARM LED
lights up and the freezer status bar
LEDs light up in sequence.
The alarm sounds, the ALARM LED
flashes and the freezer status bar
LEDs flash simultaneously.
The refrigerator and the freezer do not
cool well.
Possible causes / Solutions:
The plug has not been inserted into the electrical socket, or not far enough to
make contact, or there is no power in the house.
The appliance comes with a motor protection control (see Start-up and use).
Pull out and reverse the plug before putting it back in the socket.
The refrigerator door has been open for more than two minutes.
The buzzer stops when the door is closed or when the ALARM button is
pressed.
The temperature inside the freezer is too high. The freezer will maintain a
temperature of around 0°C so that the food will not refreeze, allowing you to eat
it within 24 hours or to refreeze it after it has been cooked.
To switch off the buzzer, press the ALARM button. Press a second time to
display the set value on the freezer status bar, switch off the ALARM LED and
restore normal operation.
The temperature of the freezer is dangerously high: the food inside must not be
eaten. The freezer will maintain a temperature of approximately 0°C.
To switch off the buzzer, press the RESET ALARM button. Press a second time
to display the set value on the freezer status bar, switch off the ALARM LED and
restore normal operation.
The doors do not close properly or the seals are damaged.
The doors are opened too frequently.
The temperature that has been set is too high (see Start-up and use).
The refrigerator or the freezer have been over-filled.
The food inside the refrigerator is
beginning to freeze.
The motor runs continuously.
The Aircooler fan does not rotate
The appliance makes a lot of noise.
Early ending of functions
The freezer status bar LEDs do not
indicate the set temperature, and are
lit in a constant manner.
The temperature that has been set is too low (see Start-up and use).
The SUPER FREEZE button has been pressed (rapid freezing): the yellow
SUPER FREEZE light is on or flashing (see Description).
The door is not closed properly or is continuously opened.
The outside ambient temperature is very high.
The thickness of the frost exceeds 2-3 mm (see Maintenance).
The refrigerator door is open.
The Aircooler system is only activated automatically when it becomes necessary
to restore perfect operational conditions inside the refrigerator compartment.
The appliance has not been installed on a level surface (see Installation).
The appliance has been installed between cabinets that vibrate and make noise.
The internal refrigerant makes a slight noise even when the compressor is off.
This is not a defect, it is normal.
Electrical disturbance on the network or brief interruptions of the power supply.
Contact the Technical Assistance Centre.
10
Assistance
Before calling for Assistance:
Check if the malfunction can be solved on your own (see Troubleshooting).
If after all the checks, the appliance still does not operate or the problem persists, call the nearest Service
Centre
model
serial number
Communicating:
type of malfunction
appliance model (Mod.)
serial number (S/N)
This information can be found on the data plate
located on the bottom left side of the
refrigerator compartment.
Gross
Bruto
Brut
TI
75
Test
P.S-I.
RG 2330
Mod.
220 - 240 V- 50 Hz 150 W
340
Total
Gross
Bruto
Brut
Compr.
R 134 a
Syst.
kg 0,090
Kompr.
Made in Italy 13918
93139180000 S/N 704211801
Net
Util
Utile
Pressure
HIGH-235
LOW 140
Cod.
Gross
Bruto
Brut
Fuse
W
A
Freez. Capac
Poder de Cong
4,0
kg/24 h
Max 15 w
Class
Clase
Classe
N
Never call on unauthorized technicians and always refuse spare parts which are not originals.
GB
11
GB
195061317.01
10/2007
12
Mode demploi
REFRIGERATEUR 2 PORTES
GB F
English,1
Français, 13
TK
Türkçe, 37
TAN 5 FNF DNX
E
Espanol, 25
Sommaire
F
Installation, 14
Mise en place et raccordement
Réversibilité des portes
Description de lappareil, 15-16
Tableau de bord
Vue densemble
Mise en marche et utilisation, 17-18-19
Mise en service de lappareil
Comment se déplacer sur lafficheur
Système de refroidissement
Pour profiter à plein de votre réfrigérateur
Pour profiter à plein de votre congélateur
Entretien et soins, 20
Mise hors tension
Nettoyage de lappareil
Contre la formation de moisissures et de mauvaises odeurs
Remplacement de lampoule déclairage
Précautions et conseils, 21
Sécurité générale
Mise au rebut
Economies et respect de lenvironnement
Anomalies et remèdes, 22
Assistance, 23
Installation
! Conservez ce mode demploi pour pouvoir le consulter à
F
tout moment. En cas de vente, de cession ou de
déménagement, veillez à ce quil suive lappareil pour informer
le nouveau propriétaire sur son fonctionnement et lui fournir
les conseils correspondants.
! Lisez attentivement les instructions : elles contiennent des
conseils importants sur linstallation, lutilisation et la sécurité
de votre appareil.
Mise en place et raccordement
Mise en place
1. Placez lappareil dans une pièce bien aérée et non humide.
2. Ne bouchez pas les grilles daération arrière : le
compresseur et le condensateur produisent de la chaleur et
exigent une bonne aération pour bien fonctionner et réduire
la consommation délectricité.
3. Prévoir au moins 10 cm entre le haut de lappareil et les
meubles installés au-dessus et au moins 5 cm entre les
côtés et les meubles/parois latérales.
4. Installez lappareil loin de sources de chaleur (rayons
directs du soleil, cuisinière électrique).
5. Pour maintenir une distance optimale entre le produit et la
paroi arrière, montez les cales despacement comprises
dans le kit dinstallation et suivez les instructions de la
notice spécialement prévue.
Réversibilité des portes
Si une inversion du sens douverture des portes savère
nécessaire, faire appel à notre service dassistance
technique.
Mise à niveau
1. Installez lappareil sur un sol plat et rigide.
2. Si le sol nest pas parfaitement horizontal, vissez ou dévissez
les petits pieds avant pour bien niveler lappareil.
Raccordement électrique
Après le transport, placez lappareil à la verticale et attendez
au moins 3 heures avant de le raccorder à linstallation
électrique. Avant de brancher la fiche dans la prise de
courant, assurez-vous que :
la prise est bien munie dune terre conforme à la loi;
la prise est bien apte à supporter la puissance maximale de
lappareil, indiquée sur la plaquette signalétique placée à
lintérieur du compartiment réfrigérateur en bas à gauche
(ex. 150 W);
la tension dalimentation est bien comprise entre les
valeurs indiquées sur la plaquette signalétique, placée en
bas à gauche (ex.220-240 V);
la prise est bien compatible avec la fiche de lappareil.
En cas dincompatibilité, faites remplacer la fiche par un
technicien agréé (voir Assistance); nutilisez ni rallonges ni
prises multiples.
! Après installation de lappareil, le câble électrique et la prise
de courant doivent être facilement accessibles.
! Le câble ne doit être ni plié ni excessivement écrasé.
! Il doit être contrôlé prériodiquement et ne peut être
remplacé que par un technicien agréé (voir Assistance).
! Nous déclinons toute responsabilité en cas de non
respect des normes énumérées ci-dessus.
14
Description de
lappareil
Tableau de bord
Réglage de la
température du
FREEZER
BOTTLE CHILL
Barre graphique
FREEZER
Barre graphique
REFRIGERATEUR
CHILD LOCK
Réglage de la
température du
RÉFRIGÉRATEUR
ECO
ON/OFF
F
ALARMES
SUPER
FREEZE
SUPER
COOL
HOLIDAY
ON/OFF
Cette touche sert à allumer lappareil tout entier
(compartiment réfrigérateur et compartiment freezer). Le
TEMOIN rouge indique que lappareil est éteint, le TEMOIN
vert quil est en service. Pour éteindre lappareil, appuyez
au moins 2 secondes de suite sur la touche ON/OFF.
ECO
Cest elle qui sert à activer ou à désactiver la fonction ECO
(la température optimale avec une faible consommation
délectricité). Dès activation de cette fonction, le TEMOIN
AUTO et le TEMOIN ECO sallument simultanément.
ALARMES
Cette touche permet de brancher et de gérer toutes les
alarmes reliées au fonctionnement de lappareil.
Child Lock
Ce dispositif permet de verrouiller les touches du tableau
de commande pour éviter toute manipulation de la part
des enfants.
Réglage de la température du REFRIGERATEUR - et +
Elles permettent de modifier le réglage de la température
du réfrigérateur, avec affichage de confirmation de la
température sélectionnée. Ces touches permettent aussi
de désactiver le compartiment réfrigérateur.
Barre graphique REFRIGERATEUR
Indication de la température sélectionnée dans le
compartiment réfrigérateur ou de sa désactivation (dans ce
cas la barre graphique est éteinte).
Barre graphique FREEZER
Affiche la température sélectionnée dans le compartiment
freezer.
SUPER COOL
Elle permet dactiver ou de désactiver la fonction SUPER
COOL (refroidissement rapide). Le temoin SUPER COOL
sallume.
SUPER FREEZE
Elle permet dactiver ou de désactiver la fonction SUPER
FREEZE. Le temoin SUPER FREEZE sallume.
HOLIDAY
Elle permet dactiver ou de désactiver la fonction HOLIDAY
(le TEMOIN AUTO et HOLIDAY sallume).
BOTTLE CHILL
Elle permet dactiver ou de désactiver la fonction BOTTLE
CHILL (il abaisse la température du congélateur le temps
nécessaire au refroidissement dune bouteille). Le temoin
BOTTLE CHILL sallume
Réglage de la température du FREEZER - e t +
Elles permettent de modifier le réglage de la température
du freezer, avec affichage de confirmation de la
température sélectionnée.
15
Loading...