Indesit SIXXL 129 S User Manual

Instructions for use
Contents
GB
English, 1
I
Italiano,13
Installation, 2-3
Unpacking and levelling Connecting the electricity and water supplies Technical details
Self-cleaning detergent dispenser drawer Control panel Load balancing system
Running a wash cycle, 6
Wash programmes, 7
Detergents and laundry, 8
Preparing the laundry Washing recommendations
WASHING MACHINE
GB
GB
SIXXL 129 S
Precautions and advice, 9
General safety Disposal Saving energy and respecting the environment Drip-tray system
Care and maintenance, 10
Cutting off the water or electricity supply Cleaning the machine Cleaning the detergent dispenser drawer Caring for the door and drum of your appliance Cleaning the pump Checking the water inlet hose
Troubleshooting, 11
Service, 12
1
Installation
GB
This instruction manual should be kept in a safe
place for future reference. If the appliance is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/herself with its operation and features.
Read these instructions carefully: they contain vital
information relating to the safe installation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Unpack the washing machine.
2. Make sure that the machine has not been damaged during the transportation process. If it has been damaged, contact the retailer and do not proceed any further with the installation process.
3. Remove the 4 protective screws (used during transportation) and the rubber washer with the corresponding spacer, located on the rear part of the appliance (see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: they will be needed again if the washing machine is moved to another location.
Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting while it is operating. If it is placed on carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the machine.
Connecting the electricity and water supplies
Connecting the water inlet hose
1. Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3/4
A
gas threaded opening
(see figure).
Before performing the connection, allow the water to run freely until it is perfectly clear.
2. Connect the inlet hose to the machine by screwing it onto the cold water inlet of the appliance, which is situated on the top right­hand side of the rear part of the appliance(see figure).
Packaging materials should not be used as toys for
children.
Levelling
Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly.
1. Install the washing machine on a flat and sturdy floor, without placing it against walls, cabinets or other furniture.
2. If the floor is not perfectly level, compen­sate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured in relation to the worktop, must not exceed 2°.
2
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical details table (see next page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Connecting the drain hose
65 - 100 cm
Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;
alternatively, place it over the edge of a basin, sink or tub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater.
Do not use extension cords or multiple sockets.
GB
The cable should not be bent or compressed.
GB
The power supply cable must only be replaced by
authorised technicians.
Warning! The company shall not be held responsible in the event that these regulations are not respected.
We advise against the use of hose extensions; if it
is absolutely necessary, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity socket, make sure that:
 the socket is earthed and complies with all
applicable laws;
 the socket is able to withstand the maximum
power load of the appliance as indicated in the Technical data table (see opposite);
 the power supply voltage falls within the values
indicated in the Technical data table(see opposite);
 the socket is compatible with the plug of the
appliance. If this is not the case, replace the socket or the plug.
The machine must not be installed outdoors, even
in covered areas. It is extremely dangerous to leave the appliance exposed to rain, storms and other weather conditions.
The mains socket must remain within easy reach
after the washing machine has been installed.
Technical details
Model
Dimensions
Capacity
Electric
connections
Wat er connections
Spin speed
Control programmes
according to EN 60456 directive
SIXXL 129 S
59.5 cm wide 85 cm high
53.5 cm deep
from 1 to 7 kg
please refer to the techni cal data plate fixed to the machine
maximum press ure 1 MPa (10 bar) mini mum pressure 0.05 MPa (0.5 bar) drum capacity 52 litres
up to 1200 rpm
programme ; run with a load of 7 kg.
This appliance is compliant with the following European Community Directives:
- 89/336/CEE of 03/05/89 (Electromagnetic Compatibility) and subsequent amendments
- 2002/96/CE
- 2006/95/CE (Low Voltage)
3
Description of the machine
GB
PORTHOLE DOOR
ADJUSTABLE FEET
Self-cleaning detergent dispenser drawer
This washing machine is fitted with an innovative self­cleaning detergent drawer which enhances the quality of each wash.
The drawer is located inside the porthole door.
CONTROL PANEL
PORTHOLE DOOR HANDLE
ACCESS PANEL FOR THE DRAIN PUMP
The detergent level can be seen through the corresponding transparent windows provided on the compartment.
Inside compartments and , there are also floating indicators (see figure B) . When the maximum quantity of detergent/fabric softener has been measured out, the indicators rise until they touch the grilles protecting the compartments.
STOP
STOP
MAX
MAX
AB
1. Open the porthole door to access the detergent
dispenser drawer (see figure A).
2. Pour the detergent or the additive into the compartments, over the protective grilles, as follows: Compartment liquid form. Compartment form and powder addititves. To place the tablets inside, lift up the grille protecting the drawer. Compartment
Pouring liquid detergent or additives into the central compartment may cause leakages to occur.
: detergent and additives in
: detergent in powder or tablet
: fabric softener.
We recommend that the maximum levels indicated on the detergent dispenser drawer are not exceeded.
We recommend that the dosage instructions on the detergent packaging are followed carefully. If using certain particularly thick types of detergent, we suggest that these are placed directly inside the drum and not in the detergent dispenser drawer.
Exceeding the maximum levels indicated on the machine may cause the detergent to leak out of the bottom part of the drawer. Exceeding the stated amount of detergent does not result in a more effective was; it simply pollutes the environment more.
The water used during the wash cycle will remove any excess detergent from the drawer. It is, however, possible to remove the drawer manually (see Care
and Maintenance).
To facilitate the process of measuring out the detergents, we recommend that the dosing device supplied with the washing machine is used. The maximum capacity of the drawer is as follows:
- liquid detergents: 1 1/2 measures
- powder detergents: 2 measures
- fabric softener: 1 measure
4
Control panel
WASHING TIME INDICATOR
lights
START DAILY WASH 30 PROGRAMME
button
ON/OFF button
DOOR LOCKED red indicator
light
START WHITE COTTON PROGRAMME
button
GB
GB
START DELICATES PROGRAMME
button
ON/OFF button: press this to switch the machine on or off.
When the machine is switched on, the buttons used to start various programmes begin to flash, while the washing time indicator lights illuminate in a fixed manner. To cancel the cycle, press and hold the on/off button
for approximately 2 seconds while the wash cycle is in progress.
indicator light will flash for a few seconds
The and the machine will automatically drain the water in the tub.
DOOR LOCKED red indicator light: when the indicator light is illuminated the door is locked to prevent it being opened accidentally; to avoid damaging the appliance, wait for the light to
switch off before opening the door after the cycle has ended or when the cycle is paused. The light will remain lit for approximately two minutes after the washing programme has finished.
START COLOUR MIX EASY-IRON PROGRAMME
button
WASHING TIME INDICATOR lights: these light up in sequence to indicate the progress of the washing programme. At the end of the programme all
the indicator lights begin to flash.
For further details, please refer to the chapter entitled
Running a wash cycle.
Load balancing system
To avoid excessive vibrations before every spin, the machine distributes the load in a uniform manner by rotating the drum continuously at a speed which is slightly greater than the washing rotation speed. When, despite repeated attempts, the load is not perfectly distributed, the machine spins at a lower speed than stated for the wash cycle. If the load is excessively unbalanced, the machine performs the distribution process instead of spinning. Balancing attempts may increase the total duration of the cycle, up to a maximum of 10 minutes.
Rapid flashing of the DOOR LOCKED indicator light indicates a fault (see Troubleshooting).
START PROGRAMME buttons: press one of these to start the selected washing programme.
- button lit in a fixed manner: programme in progress.
- buttons flashing: awaiting selection.
5
Running a wash cycle
GB
Note: Once the appliance has been installed, and
before you use it for the first time, run a wash cycle with detergent and no laundry, using the programme.
1. SWITCH ON THE MACHINE by pressing the ON/ OFF PROGRAMME buttons begin to flash and the WASHING TIME INDICATOR lights light up in a fixed manner, to indicate that the washing machine is ready to receive instructions.
2. LOAD THE LAUNDRY. Open the door using the handle. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of programmes on the following page.
3. MEASURE OUT THE DETERGENT AND ADDITIVES. Pour the detergents into the drawer located inside the porthole door, taking care not to exceed the maximum levels indicated on the surface of the drawer and by the floating indicators. For further details, please refer to the chapter entitled Description of the machine.
4. CLOSE THE DOOR.
manner, and all the wash time indicator lights switch off. The DOOR LOCKED indicator light illuminates in a fixed manner, to signal the activation of the door safety device.
For a description of the wash programmes available, please refer to the chapter entitled
Wash programmes.
The procedure used to start the DELICATES programme is different; see paragraph "Delicates
30°" on the following page.
During the programme the WASH TIME INDICATOR lights illuminate in sequence, indicating how much of the programme has already been completed.
button. The icons for the START
5. START THE WASHING PROGRAMME by pressing the corresponding START PROGRAMME BUTTON. The icon corresponding to the selected programme illuminates in a fixed
The diagram at the side refers to a situation in which approximately 50% of the cycle has been completed.
At the end of the cycle, all the WASHING TIME INDICATOR lights begin to flash.
6. The WASH PROGRAMME can be SUSPENDED by pressing the illuminated start programme button which begins to flash. After approximately two minutes the DOOR LOCKED indicator light will switch off to indicate that the door may be opened. If you wish to add more detergent, make sure that the MAX floating indicator is not in a raised position. To restart the wash programme, close the door again and press the corresponding start button once more. To guarantee maximum safety, whenever there is a quantity of water in the drum which could leak out of the machine, it will not be possible to open the door (the DOOR LOCKED indicator light will remain lit even after the two minutes have passed). The machine, in this case, should be switched off by pressing for approximately 2 seconds the ON/ OFF drained automatically.
7. AT THE END OF THE PROGRAMME At the end of the wash programme, the icon corresponding to the selected programme remains lit in a fixed manner, while all the washing time
indicator lights begin to flash.
To start a new wash cycle the machine must be switched off and switched back on again, by pressing the ON/OFF
button, then waiting for the water to be
button TWO TIMES.
6
Wash programmes
Button Fabrics
WHITE COTTON
Du rable w hite cotto n
COLOR MIX 40° / EASY IRON
Colou red cotton and synthetics
DELICATES
+ +
WASH / COLD WATER RINSE
DAILY
The duration of the programmes indicated in the table are for guidance purposes only, and are calculated based on an average load quantity.
Wool (final delicate spin cycle)
Silk and curtains (without final s pin c ycle)
Cotton and synthetics
Max.
load
Te m p er at ure
(kg)
760°C1200170
4,5 40°C 1000 105
1,5 30°C 600 50
1,5 30°C no* 50
30°/cold
3
water**
Spin
speed
(rpm )
800 30
duration
(minutes)
Cycle
Wash cycle descriptio n
Wash cycle, rinse cycles, intermediate an d final s pin cycles
Was h cycle, rinse cycles and delicate sp in cyc le
Was h cycle, rinse cycles and delicate sp in cyc le
Wash cycle, rinse cycles and drainage
Wash cycle (only if the " programme activated), rinse cycles, delicate spin cycle
Rapid
wash"
*Note: for information relating to excluding the spin cycle in the delicates programme, please refer to the
Delicates 30° paragraph further down the page.
**Note: for information relating to rinsing hand-washed clothes in cold water, please refer to the
Daily wash 30 / Cold water rinse paragraph further down the page.
WHITE COTTON 60°
Designed for the washing of all durable white cotton garments. Higher washing temperatures offer improved washing results in Class A appliances.
COLOUR MIX 40° / EASY-IRON
This programme can be used to wash all your coloured garments, whether cotton or synthetic fabric. The spin cycle is carefully controlled during the entire wash cycle, so as to reduce the formation of creases in the fabric and make it easier to iron. Cotton and synthetic garments can be washed at the same time.
DELICATES 30°
A cycle designed for the washing of all woollen, silk and delicate garments. As these garments have different
features, this programme requires an activation process which is different from the others:
+ DELICATES CYCLE WITH FINAL SPIN (for
woollen garments): press the START DELICATES PROGRAMME
button. After approximately 3 seconds, the START DELICATES PROGRAMME and START DAILY WASH PROGRAMME buttons begin to flash. Press the START DELICATES PROGRAMME
button to perform the wash, which ends with a delicate spin cycle. This programme includes drum movements which have been carefully researched to remove excess water from the fabric, thereby reducing friction and helping to protect your woollen garments.
+ DELICATES CYCLE WITH SPIN PHASE
EXCLUDED (for silk and viscose garments and for curtains; not to be used for washing wool): press the START DELICATES PROGRAMME
button. After approximately 3 seconds, the START DELICATES PROGRAMME WASH PROGRAMME the START DAILY WASH PROGRAMME
and START DAILY
buttons begin to flash. Press
button to perform the wash without the final spin cycle. At the end of the cycle, the machine will automatically drain the water contained in the drum. We recommend that the garments are removed from the washing machine straight away, in order to limit the formation of creases.
DAILY WASH 30 / COLD WATER RINSE
This programme can be used to wash lightly soiled cotton or synthetic fabrics, or garments with the "wash at 30°"
instruction on the label, in just 30 minutes. It is also possibile to rinse cotton or synthetic garments which have been washed by hand (this does not include wool or silk).
Thanks to its special sensors, the washing machine is able to recognise when the garments placed in the drum have detergent on them.
- if no detergent is detected on the clothes, the DAILY WASH 30' cycle will be performed;
- if detergent is detected (cloths which have been washed by hand), the COLD WATER RINSE cycle will be performed automatically.
AUTOMATIC RINSE MANAGEMENT
The rinse function is monitored and controlled in every programme by special sensors. If the garments are
very soapy at the end of the wash, the rinse cycle will be extended automatically until the detergent is removed completely. In this case the wash
programme duration may be slightly increased in relation to the information given in the table of programmes.
GB
GB
7
Detergents and laundry
GB
Preparing the laundry
 Divide the laundry according to:
- the type of fabric/the symbol on the label;
- the colours: separate coloured garments from whites.
 Empty all garment pockets and check the
buttons.
 Do not exceed the load values indicated for the
Wash programmes.
Washing recommendations
Bed and bathroom laundry (sheets, towels, bathrobes, etc.): use the WHITE COTTON
programme which guarantees the most efficient wash in Class A appliances. The intensive spin cycle eliminates all excess water efficiently.
White cotton garments (shirts, T-shirts, tablecloths, etc.): use the WHITE COTTON 60°
programme. If there are any stubborn stains, they should be pre-treated with solid soap before the wash cycle is started.
Coloured cotton garments (shirts, T-shirts, underwear, etc.): use the COLOUR MIX 40°
programme, which maximises the performance of the wash without damaging the colours. The spin cycle phase, thanks to the incorporated EASY IRON function, reduces the formation of creases at the end of the wash, making the fabric easier to iron. We recommend the use of liquid detergent.
White or coloured synthetic garments (shirts, T-shirts, underwear, etc.): use the COLOUR MIX
40° and coloured garments are not washed in the same wash cycle, to prevent any colour leakage from seeping into the white clothing. We recommend the use of liquid detergent.
programme. We recommend that white
How much does your laundry weigh?
1 sheet 400-500 g 1 pillow case 150-200 g 1 tablecloth 400-500 g 1 bathrobe 900-1.200 g 1 towel 150-250 g 1 pair of jeans 400-500 g 1 shirt 150-200 g
Coloured synthetic and cotton garments, with wash at 30°
the DAILY WASH 30 washing temperature protects the coloured fabrics. We recommend the use of liquid detergent.
Woollen garments (jumpers, scarves, etc.): use the DELICATES 30° programme with final spin
+ . The movement of the drum during the wash and the delicate spin cycle reduces fabric matting. We recommend the use of detergents specifically designed for woollen garments. We recommend that the maximum load level is not exceeded.
Silk garments (shirts, underwear, etc.): use the DELICATES 30° programme with the spin excluded
+ . Try not to leave the laundry in the drum for too long after the wash cycle has finished, to prevent excessive creasing.
Curtains: use the DELICATES 30° programme with the spin excluded they are folded and placed inside a pillowcase or a mesh bag. Wash them separately, making sure the maximum load level is not exceeded.
instruction on the care label: use
programme. The low
+ . We recommend
8
Loading...
+ 16 hidden pages