Indesit I5GMH5AG User Manual

I5GMH6AG/ UA

English

EnglishEnglish

Operating Instructions

COOKER AND OVEN

Contents

Operating Instructions,1 AVVERTENZA,2 Description of the appliance-Overall view,3 Description of the appliance-Control Panel,4 Installation,5 Start-up and use,9 Cooking modes,10 Precautions and tips,14 Care and maintenance,15 Assistance,16

Інструкціі з експлуатаціі

КУХНЯ

Зміст

Інструкціі з експлуатаціі,1 УВАГА,2 Опис установки-Загальнии вигляд,3 Опис установки-Панель управління,4 Встановлення,17 Включення і використання,21 Запобіжні засоби і поради,26 Догляд i технічне обслуговування,27 Допомога,27

AVVERTENZA

УВАГА

УВАГАУВАГА

ATTENZIONE: Questo apparecchio e le sue par accessibili diventano molto caldi durante l’uso. Bisogna fare a enzione ed evitare di toccare gli elemen riscaldan . Tenere lontani i bambini inferiori agli 8 anni se non con nuamente sorveglia . Il presente apparecchio può essere u lizzato dai bambini a par re dagli 8 anni e da persone con rido e capacità ﬁ siche, sensoriali o mentali oppure con mancanza di esperienza e di conoscenza se si trovano so o adeguata sorveglianza oppure se sono sta istrui circa l’uso dell’apparecchio in modo sicuro e se si rendono conto dei pericoli correla . I bambini non devono giocare con l’apparecchio. Le operazioni di pulizia e di manutenzione non devono essere eﬀ e uate dai bambini senza sorveglianza. ATTENZIONE: Lasciare un fornello incustodito con grassi e olii può essere pericoloso e può provocare un incendio. Non bisogna MAI tentare di spegnere una ﬁ amma/incendio con acqua, bensì bisogna spegnere l’apparecchio e coprire la ﬁ amma per esempio con un coperchio o con una coperta ignifuga. Non u lizzare prodo abrasivi né spatole di metallo taglien per pulire lo sportello in vetro del forno in quanto potrebbero graﬃ are la superﬁ cie, provocando, così, la frantumazione del vetro. Le superﬁ ci interne del casse o (se presente) possono diventare calde. Non u lizzare mai pulitori a vapore o ad alta pressione per la pulizia dell’apparecchio. Eliminare eventuali liquidi presen sul coperchio prima di aprirlo. Non chiudere il coperchio in vetro (se presente) con i bruciatori gas o la piastra ele rica ancora caldi. ATTENZIONE: Assicurarsi che l’apparecchio sia spento prima di sos tuire la lampada per evitare la possibilità di scosse ele riche. ATTENZIONE: l’uso di protezioni del piano

inappropriate può causare inciden .

! When you place the rack inside, make sure that the stop is directed upwards and in the back of the cavity.

УВАГА! Під час роботи цей прилад, а також його доступні частини нагріваються до високих температур. Слід бути особливо обережними, щоб не торкатися нагрівальних елементів. Діти віком до 8 років мають знаходитися на небезпечній відстані від приладу, якщо неможливо забезпечити постійний контроль над ними. Дозволяється користування цим приладом дітьми віком від 8 років, а також особами з обмеженими фізичними, сенсорними або розумовими можливостями або особами без належного досвіду і знань, якщо вони перебувають під постійним контролем або проінструктовані щодо правил з небезпечного користування приладу і усвідомлюють ступені ризику. Не дозволяйте дітям гратися з приладом. Операції з очищення і догляду не повинні виконуватися дітьми без належного контролю. УВАГА! Небезпечно залишати без нагляду плити з жиром або олією, тому що це може призвести до пожежі. НІ В ЯКОМУ РАЗІ не слід намагатися погасити полум’я/пожежу водою. Необхідно вимкнути прилад і накрити полум’я, наприклад, кришкою або вогнетривким покривалом. Не використовувати абразивні засоби ані металеві загострені шпателі для очищення скляних дверцях духовки, тому що вони можуть пошкрябати поверхню, призводячи

до

розтріскування скла. Внутрішні поверхні відділення (де вони наявні) можуть нагріватися до високих температур. Забороняється використання апаратів для очищення парою або високим тиском. Витріть насухо всі наявні на кришці рідини, перш ніж відкрити її. Не закривайте скляну кришку (якщо вона наявна), якщо газові пальники або електричні конфорки залишаються нагрітими. УВАГА! Щоб запобігти враженню електричним струмом переконайтеся в тому, що прилад вимкнений, перш ніж заміняти лампочку. УВАГА! використання невідповідних захисних пристроїв варильної поверхні може призвести до нещасних випадкіâ.

! ɉɿɞ ɱɚɫɬ ɜɫɬɚɜɥɹɧɧɹ ɪɟɲɿɬɤɢ ɫɥɿɞ ɩɟɪɟɤɨɧɚɬɢɫɹ, ɳɨ ɫɬɨɩɨɪ ɩɨɜɟɪɧɭɬɢɣ ɜɝɨɪɭ ɿ ɜɫɟɪɟɞɢɧɭ ɧɿɲɿ .

1 2

Description

Overall view

1.Hob burner

2.Hob Grid

3.Control panel

4.Sliding grill rack

5.DRIPPING pan

6.Adjustable foot

7.Containment surface for spills

8.GUIDE RAILS for the sliding racks

9.position 5

10.position 4

11.position 3

12.position 2

13.position 1

14.Glass Cover (Available only on certain models)

Опис пристрою загальний вид

9 10 11 12 13 6

1.Hob пальники

2.Hob сітки

3.Control панелі

4.Sliding гриль стійці

5.DRIPPING каструлі

6.Adjustable ногу

7.Containment поверхню для розливу

8.GUIDE РЕЙКИ для розсувних стелажів

9.position 5

10.position 4

11.position 3

12.position 2

13.position 1

14.Glass Обкладинка (Доступно тільки на деяких моделях)

Description of the appliance

Control panel

Опис плити

Панель управління

1.Electronic cooking programmer

2.TIMER button

3.COOKING TIME button

4.COOKING END TIME button

5.THERMOSTAT knob

6.THERMOSTAT indicator light

7.SELECTOR knob

8.Hob BURNER control knob

1.Електронний програматор приготування їжі

2.Кнопка ТАЙМЕР

3.Кнопка ТРИВАЛІСТЬ ПРИГОТУВАННЯ

4.Кнопка ЗАКIНЧЕННЯ ПРИГОТУВАННЯ

5.Peґyлятор TEPMOCT ATУ

6. Індикатор TEPMOCT ATУ

7.Peґyлятор РСПГСБМ

8.Ручки для керування газовими

пальниками на варильній поверхні

Installation

! Before operating your new appliance please read this instruction booklet carefully. It contains important information concerning the safe installation and operation of the appliance.

! Please keep these operating instructions for future reference. Make sure that the instructions are kept with the appliance if it is sold, given away or moved.

! The appliance must be installed by a qualified professional according to the instructions provided.

! Any necessary adjustment or maintenance must be performed after the cooker has been disconnected from the electricity supply.

Room ventilation

The appliance may only be installed in permanentlyventilated rooms, according to current national legislation. The room in which the appliance is installed must be ventilated adequately so as to provide as much air as is needed by the normal gas combustion

process (the flow of air must not be lower than 2 m

/h per kW of installed power). The air inlets, protected by grilles, should have a duct

with an inner cross section of at least 100 cm

and should be positioned so that they are not liable to even partial obstruction (see  gure A). These inlets should be enlarged by 100% - with a

minimum of 200 cm

- whenever the surface of the hob is not equipped with a flame failure safety device. When the flow of air is provided in an indirect manner from adjacent rooms (see  gure B), provided that these are not communal parts of a building, areas with increased fire hazards or bedrooms, the inlets should be fitted with a ventilation duct leading outside as described above.

Disposing of combustion fumes

The disposal of combustion fumes should be guaranteed using a hood connected to a safe and efficient natural suction chimney, or using an electric fan that begins to operate automatically every time the appliance is switched on (see  gure).

Fumes channelled straight outside

Fumes channelled through a chimney or a branched flue system (reserved for cooking appliances)

! The liquefied petroleum gases are heavier than air and collect by the floor, therefore all rooms containing LPG cylinders must have openings leading outside so that any leaked gas can escape easily. LPG cylinders, therefore, whether partially or completely full, must not be installed or stored in rooms or storage areas that are below ground level (cellars, etc.). Only the cylinder being used should be stored in the room; this should also be kept well away from sources of heat (ovens, chimneys, stoves) that may cause the temperature of the cylinder to rise above 50°C.

Positioning and levelling

! It is possible to install the appliance alongside cupboards whose height does not exceed that of the hob surface.

Ventilation opening for comburent air

Adjacent room Room requiring

Increase in the gap between the door and

ventilation

the flooring

! After prolonged use of the appliance, it is advisable to open a window or increase the speed of any fans used.

! Make sure that the wall in contact with the back of the appliance is made from a non-flammable, heatresistant material (T 90°C).

To install the appliance correctly:

• Place it in the kitchen, dining room or the bed-sit (not in the bathroom).

• If the top of the hob is higher than the cupboards, the appliance must be installed at least 200 mm away from them.

• If the cooker is installed underneath a wall cabinet, there must be a minimum distance of 420 mm between this cabinet and the top of the hob.

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

• If the cooker is installed underneath a wall cabinet, there must be a minimum distance of 420 mm between this cabinet and the top of the hob. This distance should be increased to 700 mm if the wall cabinets are flammable (see  gure).

• Do not position blinds behind the cooker or less than 200 mm away from its sides.

• Any hoods must be installed according to the instructions listed in the relevant operating manual.

• The voltage is in the range between the values indicated on the data plate.

• The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only.

Levelling

If it is necessary to level the appliance, screw the adjustable feet into the places provided on each corner of the base of the cooker (see  gure).

The legs* fit into the slots on the underside of the base of the cooker.

Electrical connection

Install a standardised plug corresponding to the load indicated on the appliance data plate (see Technical data table). The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains. The circuit-breaker must be suitable for the charge indicated and must comply with NFC 15-100 regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must be positioned so that it does not come into contact with temperatures higher than 50°C at any point.

Before connecting the appliance to the power supply, make sure that:

• The appliance is earthed and the plug is compliant with the law.

• The socket can withstand the maximum power of the appliance, which is indicated by the data plate.

! The manufacturer declines any liability should these safety measures not be observed.

Gas connection

Connection to the gas network or to the gas cylinder may be carried out using a flexible rubber or steel hose, in accordance with current national legislation and after making sure that the appliance is suited to the type of gas with which it will be supplied (see the rating sticker on the cover: if this is not the case see below). When using liquid gas from a cylinder, install a pressure regulator which complies with current national regulations. To make connection easier, the gas supply may be turned sideways*: reverse the position of the hose holder with that of the cap and replace the gasket that is supplied with the appliance.

! Check that the pressure of the gas supply is consistent with the values indicated in the Table of burner and nozzle specifications (see below). This will ensure the safe operation and durability of your appliance while maintaining efficient energy consumption.

Gas connection using a flexible rubber hose

Make sure that the hose complies with current national legislation. The internal diameter of the hose must measure: 8 mm for liquid gas supply; 13 mm for methane gas supply.

Once the connection has been performed, make sure that the hose:

• Does not come into contact with any parts that reach temperatures of over 50°C.

• Is not subject to any pulling or twisting forces and that it is not kinked or bent.

• Does not come into contact with blades, sharp corners or moving parts and that it is not compressed.

• Is easy to inspect along its whole length so that its condition may be checked.

• Is shorter than 1500 mm.

• Fits firmly into place at both ends, where it will be fixed using clamps that comply with current regulations.

Adjusting the hob burners’ minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory screw, which is positioned inside or next to the tap pin, until the flame is small but steady. ! If the appliance is connected to a liquid gas supply, the regulatory screw must be fastened as tightly as possible.

3. While the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame is not extinguished.

! If one or more of these conditions is not fulfilled or if the cooker must be installed according to the conditions listed for class 2 - subclass 1 appliances (installed between two cupboards), the flexible steel hose must be used instead (see below).

Connecting a flexible jointless stainless steel pipe to a threaded attachment

Make sure that the hose and gaskets comply with current national legislation. To begin using the hose, remove the hose holder on the appliance (the gas supply inlet on the appliance is a cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose length does not exceed a maximum of 2 metres, making sure that the hose is not compressed and does not come into contact with moving parts.

Checking the tightness of the connection

When the installation process is complete, check the hose fittings for leaks using a soapy solution. Never use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas other than the default type (this is indicated on the rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off their seats.

2. Unscrew the nozzles using a 7 mm socket spanner (see  gure), and replace them with nozzles suited to the new type of gas (see Burner and nozzle speci cations table).

3. Replace all the components by following the above

instructions in reverse.

! The hob burners do not require primary air adjustment.

! After adjusting the appliance so it may be used with a different type of gas, replace the old rating label with a new one that corresponds to the new type of gas (these labels are available from Authorised Technical Assistance Centres).

! Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet hose in accordance with current national regulations relating to “regulators for channelled gas”.

Safety Chain

! In order to prevent accidental tipping of the appliance, for example by a child climbing onto the oven door, the supplied safety chain MUST be installed!

The cooker is fitted with a safety chain to be fixed by means of a screw (not supplied with the cooker) to the wall behind the appliance, at the same height as the chain is attached to the appliance. Choose the screw and the screw anchor according to the type of material of the wall behind the appliance. If the head of the screw has a diameter smaller than 9mm, a washer should be used. Concrete wall requires the screw of at least 8mm of diameter, and 60mm of length. Ensure that the chain is fixed to the rear wall of the cooker and to the wall, as shown in figure, so that after installation it is tensioned and parallel to the

ground level.

S

R

A

Table of burner and nozzle specifications

Table 1 Liquid Gas Natural Gas

Burner Diameter

(mm)

Fast (Large)(R)

Semi Fast (Medium)(S)

Auxiliary (Small)(A)

100 3.00 0.7 41 87 218 214 128 286

75 1.90 0.4 30 70 138 136 104 181

51 1.00 0.4 30 52 73

Supply Pressures

I5GMH6AG/ UA

Thermal Power

kW (p .c.s.*)

By-Pass

1/100

Nozzle

1/100

Flow*

g/h

Nominal Reduced (mm) (mm) *** ** (mm)

71 76 95

Nominal (mbar)

Minimum (mb a r)

Maxi mu m (mb ar)

30 20 35

TABLE OF CHARACTERISTSICS Dimensions (with

drawn guide rails)

Volume (with drawn guide rails)

Maximum absorber power:

Dimensions of the lower compartment

Burners

ENERGY LABEL

Nozzle

width 391 mm height 340 mm depth 424 mm

57 l

See data plate

may be adapted for use with any type of gas shown on the data plate, which is located inside the flap or, after the oven compartment has been opened, on the left-hand wall inside the oven.

width 42 cm height 23 cm depth 44 cm

may be adapted for use with any type of gas shown on the data plate, which is located inside the flap or, after the oven compartment has been opened, on the left-hand wall inside the oven.

Directive 2002/40/EC on the label of electric ovens. Standard EN 50304

Energy consumption for Natural convection – heating mode: Convection;

Declared energy consumption for Forced convection Class – heating mode: Baking

1/100

Flow*

l/h

20 17 25

This appliance conforms to the

following European Economic Community directives: 2006/95/EC dated 12/12/06 (Low Voltage) and subsequent amendments 2004/108/EC dated 15/12/04 (Electromagnetic Compatibility) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments. 2002/96/EC 2009/142 of 30/11/09 (Gas) 1275/2008 (Stand-by/ Off mode)

Start-up and use

Using the hob

Lighting the burners

For each BURNER knob there is a full ring showing the strength of the flame for the relevant burner. To light one of the burners on the hob:

1. Bring a flame or gas lighter close to the burner.

2. Press the BURNER knob and turn it in an anticlockwise direction so that it is pointing to the maximum flame setting .

3. Adjust the intensity of the flame to the desired level by turning the BURNER knob in an anticlockwise direction. This may be the minimum setting , the maximum setting  or any position in between the two.

If the appliance is fitted with an electronic lighting

device* (C), press the BURNER knob and turn it in an anticlockwise direction, towards the minimum flame setting, until the burner is lit. The burner may be extinguished when the knob is

released. If this occurs, repeat the operation, holding the knob down for a longer period of time. f the appliance is equipped with a flame failure safety device (X), press and hold the BURNER knob for approximately 3-7 seconds to keep the flame alight and to activate the device.

! If the flame is accidentally extinguished, switch off the burner and wait for at least 1 minute before attempting to relight it.

To switch the burner off, turn the knob until it reaches the stop position •. When the selector knob is in any position other than the off position, the ‘on’ light is illuminated.

To identify the type of burner, please refer to the diagrams contained in the “Burner and nozzle specifications”.

Using the oven

! The first time you use your appliance, heat the empty oven with its door closed at its maximum temperature for at least half an hour. Ensure that the room is well ventilated before switching the oven off and opening the oven door. The appliance may emit a slightly unpleasant odour caused by protective substances used during the manufacturing process burning away.

! Before operating the product, remove all plastic film from the sides of the appliance.

! Never put objects directly on the bottom of the oven; this will avoid the enamel coating being damaged.

1. Select the desired cooking mode by turning the SELECTOR knob.

2. Select the recommended temperature for the cooking mode or the desired temperature by turning the THERMOSTAT knob. A list detailing cooking modes and suggested cooking temperatures can be found in the relevant table (see Oven cooking advice table).

During cooking it is always possible to:

• Change the cooking mode by turning the SELECTOR knob.

• Change the temperature by turning the THERMOSTAT knob.

• Stop cooking by turning the SELECTOR knob to the “0” position.

! Always place cookware on the rack(s) provided.

THERMOSTAT indicator light

Practical advice on using the burners

For the burners to work in the most efficient way possible and to save on the amount of gas consumed, it is recommended that only pans that have a lid and a flat base are used. They should also be suited to the size of the burner:

Burner Cookware diameter (cm)

When this is illuminated, the oven is generating heat. It switches off when the inside of the oven reaches the selected temperature. At this point the light illuminates and switches off alternately, indicating that the thermostat is working and is maintaining the temperature at a constant level.

Oven light

Fast (R) 24 - 26 Semi Fast (S) 16 - 20

Auxiliary (A) 10 - 14

This is switched on by turning the SELECTOR knob to any position other than “0”. It remains lit as long as the

oven is operating. By selecting light is switched on without any of the heating elements being activated.

 with the knob, the

+ 19 hidden pages