How it Works
Indesit
Loading...
FIDM20
User Manual
44 pgs1.24 Mb0

Indesit FIDM20, FID20 User Manual

Electric built in Double oven
Instructions for installation and use
FID20 FIDM20
Contents
You must read these instructions prior to using the
appliance and retain them for future reference.
1
Introduction
Your new appliance is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance has been installed in accordance with the installation instructions detailed in this booklet.
To help make best use of your cooking equipment, please read this booklet carefully.
The cooker is designed specifically for domestic use and responsibility will not be accepted for use in any other installation.
When the cooker is first used an odour may be emitted,
To help remove the ‘new’ smell, heat up the empty ovens to maximum temperature for a minimum of two or three hours, keeping the oven doors closed. Ensure that the room is well ventilated (e.g. open a window or use an extractor fan) and that persons who may be sensitive to the odour avoid any fumes. It is suggested that any pets be removed from the room until the smell has ceased. This odour is due to temporary finish on oven liners and elements and also any moisture absorbed by the insulation.
* The guarantee is subject to the provisions that the appliance:
(a) Has been used solely in accordance with the Users Instruction Book. (b) Has been properly connected to a suitable supply voltage as stated on the
rating plate attached to this equipment.
(c) Has not been subjected to misuse or accident or been modified or repaired by
any person other than the authorised employee or agent.
(d) Has been correctly installed.
Disposal of your product
To minimise the risk of injury to children please dispose of your product carefully and safely. Remove all doors and lids. Remove the mains cable (where fitted) by cutting off flush with the appliance and always ensure that no plug is left in a condition where it could be connected to the electricity supply. To help the environment, Local Authority instructions should be followed for the disposal of you product.
this will cease after a period of use
This appliance conforms to the following EEC Directives:
Electromagnetic Compatibility Low Voltage Equipment 89/336/EEC 73/23/EEC 92/31/EEC 93/68/EEC 93/68/EEC
2
Safety Information
When used properly your appliance is completely safe but as with any electrical product
PLEASE READ THE PRECAUTIONS BELOW BEFORE USING YOUR APPLIANCE.
there are certain precautions that must be observed.
Always
Always make sure you remove all packaging and literature from inside the oven
●
and grill compartments before switching on for the first time. Always make sure you understand the controls prior to using the appliance.
●
Always keep children away from the appliance when in use as the surfaces will
●
get extremely hot during and after cooking. Always make sure all controls are turned off when you have finished cooking
●
and when not in use. Always stand back when opening an oven door to allow any build up of steam or
●
heat to disperse. Always use dry, good quality oven gloves when removing items from the
●
oven/grill. Always take care to avoid heat/steam burns when operating the controls.
●
Always turn off the electricity supply at the wall switch before cleaning and
●
allow the appliance to cool. Always make sure the shelves are in the correct position before switching on the
●
oven. Always keep the oven and grill doors closed when the appliance is not in use.
●
Always take care when removing utensils from the top oven when the main oven
●
is in use as the contents may be hot. Always keep the appliance clean as a build up of grease or fat from cooking can
●
cause a fire. Always follow the basic principles of food handling and hygiene to prevent the
●
possibility of bacterial growth. Always keep ventilation slots clear of obstructions.
●
Always refer servicing to a qualified appliance service engineer.
●
During use the oven becomes hot. Care should be taken to avoid touching
●
heating elements inside the oven,
SAFETY ADVICE
IN THE EVENT OF A CHIP PAN OR ANY OTHER PAN FIRE:
1. TURN OFF THE COOKER APPLIANCE AT THE WALL SWITCH.
2. COVER THE PAN WITH A FIRE BLANKET OR DAMP CLOTH, this will smother the flames and extinguish the fire.
3. LEAVE THE PAN TO COOL FOR AT LEAST 60 MINUTES BEFORE MOVING IT. Injuries are often caused by picking up a hot pan and rushing outside with it. NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN FIRE as the force of the extinguisher is likely to tip the pan over. Never use water to extinguish oil or fat fires.
3
Safety Information
Never
Never leave children unsupervised where a cooking appliance is installed as all
●
cooking surfaces will be hot during and after use. Never allow anyone to sit or stand on any part of the appliance.
●
Never store items above the appliance that children may attempt to reach.
●
Never remove the oven shelves whilst the oven is hot.
●
Never heat up unopened food containers as pressure can build up causing the
●
container to burst. Never store chemicals, food stuffs or pressurised containers in or on the
●
appliance, or in cabinets immediately above or next to the appliance. Never operate the grill with the door closed as this will cause the appliance to
●
overheat. Never use the appliance as a room heater.
●
Never use the grill to warm plates.
●
Never dry any items on the oven doors.
●
Never install the appliance next to curtains or other soft furnishings.
●
Never allow children to play with the appliance controls.
●
Never use ‘steam cleaners’.
●
4
Features (FID20 only)
WARNING: Do not touch the glass doors when the oven is in use as these areas can
TOP OVEN
TEMPERATURE & GRILL
SELECTION CONTROL
GRILL
SETTING
CONTROL
❍
GRILL
ELEMENT
GRILL PAN &
FOOD SUPPORT
INNER DOOR
GLASS
OVEN LIGHT
CATALYTIC
LINER
❍
become hot.
MAIN OVEN TEMPERATURE
& FUNCTION CONTROL
TIMER
❍
CATALYTIC
LINER
GRILL SHELF
TOP OVEN
DOOR
FAN GRILL
ELEMENT
OVEN SHELF
OVEN FAN
INNER DOOR
GLASS
RATING PLATE
NEVER line the shelves, floor or sides of the oven or grill with aluminium foil as
overheating and damage may result.
5
MAIN OVEN
DOOR
Features (FIDM20 only)
WARNING: Do not touch the glass doors when the oven is in use as these areas can
TOP OVEN
TEMPERATURE CONTROL /
GRILL SELECT
TOP OVEN
PILOT LIGHT
GRILL
SETTING
CONTROL
GRILL
ELEMENT
GRILL PAN &
FOOD SUPPORT
INNER DOOR
GLASS
OVEN LIGHT
CATALYTIC
LINER
❍
❍
become hot.
MAIN OVEN
TEMPERATURE
TIMER
CONTROL
MAIN OVEN PILOT LIGHT
❍
❍
MULTIFUNCTION
SELECTOR
CATALYTIC
LINER
GRILL SHELF
TOP OVEN
DOOR
FAN GRILL
ELEMENT
OVEN SHELF
OVEN FAN
INNER DOOR
GLASS
RATING PLATE
NEVER line the shelves, floor or sides of the oven or grill with aluminium foil as
overheating and damage may result.
MAIN OVEN
DOOR
6
Temperature Conversion Chart
The chart below gives details of comparisons of oven settings for gas conventional ovens and fan oven in degrees ˚F and ˚C
GAS
MARK
1
2
/ 1 2 3 4 5 6 7 8 9
CONVENTIONAL
OVEN
˚F ˚C
250 120 275 140 300 150 325 160 350 180 375 190 400 200 425 220 450 230 475 240
FAN
OVEN
˚C
100 120 130 140 160 170 180 200 210 220
7
Controls (FID20 only)
A
GRILL SETTING
CONTROL
B
TOP OVEN TEMPERATURE
AND GRILL SELECTION
Control Markings
Control Knob
A
B
C
CONTROL
Description
Grill Setting Control
Top Oven Temperature &
Grill Selection Control
Main Oven Temperature &
Function Control
TIMER
C
MAIN OVEN TEMPERATURE
AND FUNCTION
CONTROL
Function
Selects the heat at which the grill will cook the food. 1 – max Grill Settings Control:
Note: To grill you must first select a grill function using control (B).
100 -
220
1 = Low, max = High
- Selects the cooking temperature (Degrees Centigrade) when using the top oven as a conventional oven
- Switches the top oven to ‘Half Grill’ mode.
- Switches the top oven to ‘Full Grill’ mode.
Fan Only Setting
- This is used to decrease the amount of time required to defrost food items.
Oven Light Only
- Switches on the Main Oven Interior Light Only.
.
Main Oven Temperature Scale (In
90 -
Degrees Centigrade).
230
- When cooking select the required cooking temperature.
Cooling Fan: A gentle flow of air will be blown below the control panel when any
selector switch is used. Note: Whenever the appliance has been used, the cooling fan may run on or restart itself after all the controls have been turned off. This indicates that the appliance is still warm.
Oven Interior The oven lights are operated when their respective oven control is Lights used. (N.B. Not all models have a top oven interior light).
The main oven has a light only position.
Note: It is advisable to check that all oven controls have been switched off when you have
finished using the appliance.
8
Controls (FIDM20 only)
TOP OVEN PILOT
B
TOP OVEN TEMPERATURE CONTROL
A
GRILL SETTING CONTROL
AND GRILL SELECT
TIMER
MAIN OVEN PILOT
D
MULTIFUNCTION SELECTOR
C
MAIN OVEN TEMPERATURE CONTROL
IMPORTANT
Before using your oven in the ordinary way, ALWAYS make sure that the timer has been set to MANUAL operation. Unless this is done, the main oven cannot heat up. Before seeking assistance, make sure this is done (refer to oven timer operation).
MULTIFUNCTION SELECTOR
Rotate the control knob in either direction to the required function. Many of the functions will also require the main oven thermostat to be set before the oven will heat up.
MAIN OVEN TEMPERATURE CONTROL
This is used in addition to the multifunction selector. This is used for the functions: fan oven, fan grill, half grill and full grill and convection oven. Turn the control clockwise to set the oven thermostat to the required temperature. If the timer is set correctly and the selector switch set to a suitable function an indicator light will illuminate (Fan Oven, Convection Oven and Fan Grilling modes only). This will remain on until the oven reaches the required temperature. This light will then cycle on and off as the thermostat maintains control of the oven temperature.
TOP OVEN TEMPERATURE CONTROL
Turn the control clockwise to set the top oven thermostat to the required temperature. An indicator light will illuminate. This will remain on until the oven reaches the required temperature. This light will then cycle on and off as the thermostat maintains control of the oven thermostat.
GRILL CONTROL
The grill control is designed to provide variable heat control of either both grill elements on together or the single left-hand grill element only. Turn the top oven control clockwise past the temperature settings to the half grill or full grill settings, depending on which you require. To set the grill power, turn the grill control to any setting 1 - 6.
After use always set the oven control back to ‘O’ (Off).
COOLING FAN
A gentle flow of air will be blown below the control panel when any control is used. In some instances this will continue after switching off. This helps to keep the control panel and knobs cool.
9
Multifunction Selector Switch (FIDM20 only)
The Multifunction selector switch is used when operating the main oven. With the exception of the O position the main oven light will remain on when this selector switch is used.
Off
With the selector in this position the main oven will not heat up. The timer will still operate.
Fan Oven
The oven fan and a rear element are controlled when this function is select­ed. Use the main oven thermostat control to set the required temperature.
Convection Oven
Top and base elements are controlled when this function is selected. Use the main oven thermostat to set the required temperature.
Full Grill
Both inner and outer grill elements will be on in this position. Use the oven thermostat control to set the required temperature.
Oven door must be op
Fan Grill
The oven fan and fan grill element are controlled when this function is select­ed. Use the oven thermostat control to set the required temperature.
Oven door must be closed grilling.
Fan Only
The oven fan will operate when this function is selected. The oven thermostat control must be set in the off position.
Light Only
en for grilling.
for fan
Half Grill
With this function selected only the inner element of the grill will be on. Use the oven thermostat control to set the required temperature.
Oven door must be open for grilling.
This function switches on the oven light only.
10
Oven Timer Operation
Note: Timer must be set to ‘Time of Day’ and ‘Manual’ before the ovens can be used.
Automatic Cooking
Hints on Automatic Cooking
The Main Oven (only) can be controlled by the automatic timer.
NEVER operate the grill or top oven when the main oven is set to cook automatically because the oven cavity can become warm and this may cause bacterial growth in food.
1. Select foods which will require the same cooking time and temperature.
2. To ensure food does not cool down and require reheating, set the end time so the food is ready when you require it.
3. Always ensure that meat and poultry is defrosted before placing in the oven.
4. Whenever possible, take food out of the refrigerator and keep it as cool as possible.
5. If cooking food that requires frying before placing in the oven for auto cooking, keep the delay start time to a minimum.
6. Never place hot or warm food in the oven for delay start cooking as it could cause the oven to be warm and produce harmful bacteria in the food.
7. We advise that dishes containing left-over cooked poultry or meat, e.g. Shepherd's Pie, should not be cooked automatically if there is to be a delay period.
8. Ensure that delay start times are kept to a minimum to prevent bacterial growth in food.
9. Wine or beer may ferment and cream may curdle during the delay period so it is best to add these ingredients just before serving.
10. Foods which discolour should be protected by coating in fat or tossing in water to which lemon juice has been added, prior to placing food in the oven.
11. Dishes containing liquid should not be filled too full to prevent boiling over.
12. Food should be well sealed (but not airtight) in a container to prevent the loss of liquid during cooking. Aluminium foil gives a good seal.
13. Always ensure that food is piping hot and cooked thoroughly before serving.
14. Only reheat food once.
11
Know Your Timer
CLOCKFACE
The timer incorporates a 24 hour clock.
Ensure the correct time of day is always set, before using your cooker.
SYMBOLS
A ‘bell’ symbol will light up when you select a Minute Minder Period and will remain lit for the period set. At the end of the Minute Minder Period, the timer will emit an audible tone and the ‘bell’ symbol will disappear.
The ‘cookpot’ symbol will light up either:– – When the timer is in manual mode, or – During the actual Cook Period.
‘AUTO’ will light up:– – When the timer is first turned on it will flash. It will go out when a time of day
The ‘AUTO’ symbol will flash at the end of an Auto Cooking programme to indicate that the programme has finished.
(When the ‘AUTO’ symbol is flashing, to return the oven to Manual operation, turn the oven controls off, ensure that the correct time of day is set, and press the “Manual” button – The ‘AUTO’ symbol will go out).
is set or when the timer is set to manual.
TIMER FUNCTION BUTTONS
Minute Minder Button
Here you can set a time period of up to 23 hours 59 minutes, that will count down. When it reaches zero, the timer will emit an audible tone.
For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.
AUTO COOKING PROGRAMME
Cook Period Button
End Time Button
Manual Button
“+” and “–” Buttons
Cook Period is the actual length of time for which, the timer will switch the oven(s) on as part of an “Auto Cooking” programme. (e.g. If you set 2 hours, the food will be cooked for 2 hours).
The time of day at which you want an “Auto Cooking” programme to end For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00. The
timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00. You will hear a audible tone at 11:00, to indicate that the Auto Cooking Programme has finished.
Notes:
- When setting an Auto Cooking programme you will need to set the oven control(s) to the required temperature(s) when you set the timer.
- If an Auto Cooking programme has been set the oven(s) will only operate during the pre-programmed time.
Needs to be pressed to cancel an Auto Cooking programme and return the oven(s) to Manual operation.
Used to adjust the various timer function settings.
.
12
Electronic Clock and Automatic Oven Timer Operation
SETTING THE TIME OF DAY
Step 1 Make sure all oven controls are turned Off.
Step 2 Check the electricity supply to the cooker is turned on.
Step 3 When switched on the display will show 0.00 and the Auto symbol,
flashing intermittently.
Step 4 Press & hold in both the Cook Period & End Time buttons together.
Step 5 With the Cook Period & End Time buttons still held in, press either the “+”
or “–” buttons to set the correct time of day.
Step 6 Release all the buttons simultaneously.
THE TIME OF DAY IS NOW SET.
To change the time of day repeat Steps 4, 5 & 6 above.
Note: You cannot adjust the time of day if the timer has been set for an
Auto Cooking Programme.
SETTING THE MINUTE MINDER
Step 1 Ensure the time of day is set correctly.
Step 2 Press and hold the Minute Minder button.
Step 3 With the Minute Minder button held in, set the required Minute Minder
period using the “+” and “–” buttons. A ‘bell’ symbol will light up.
Release all buttons and the timer display will revert back to the time of day. The ‘bell’ symbol will remain lit to signify that a Minute Minder period has been set.
At the end of the set time an audible tone will be heard, and the ‘bell’ symbol will disappear.
Step 4 To cancel the audible tone press the Minute Minder button.
Note 1 When the Minute Minder has been set, the time remaining can be checked at any
time by simply pressing the Minute Minder button.
Note 2 If necessary the Minute Minder can be cancelled before the tone sounds by press
ing and holding the Minute Minder button and then at the same time pressing the “–” button until 0.00 appears in the display window.
13
Loading...
+ 30 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use