Indesit D 66 User Manual

Dishwasher

Instruction for installation and use

D 66

Safety Is a Good Habit to Get Into

NOTICE
Carefully read the instructions contained in this manual, as
they provide important information which is essential to safe
and proper installation, use and maintenance of the
appliance.

This appliance complies with the following EEC
directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;

- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility)
and subsequent modifications.

1.Carefully dispose of the packing material.

2.After removing the packing, check to make sure that the

appliance is not damaged. If in doubt, contact a qualified
professional.

3.The dishwasher must only be used by adults for the washing
of household dishes and cooking utensils.

4.Fundamental rules to follow when using the appliance:

- Never touch the dishwasher when barefoot or with wet
hands or feet;

- We discourage the use of extension cords and multiple
sockets;

- During installation, the power supply cord must not be

excessively or dangerously bent or flattened;

- If the appliance is not operating properly or maintenance
must be performed, disconnect the appliance from the power
supply .

5.Keep detergents out of the reach of children, who must
also be kept away from the dishwasher when it is open.

6.This appliance cannot be installed outdoors, not even if
the area in which it is installed is covered by a roof; it is also
very dangerous to leave it exposed to the rain and elements.

7.Do not touch the heating element during or after a wash
cycle.

8.Do not lean or sit on the door when it is open, as this
could overturn the dishwasher.

9.If the appliance malfunctions, turn off water supply to the
appliance and disconnect the plug from the wall socket.
Then, consult the section entitled, "T roubleshooting." If you
cannot resolve the problem, contact a service centre.

10.Appliances which are no longer being used must be made
inoperable by cutting the power supply cord and removing
the door lock.

To maintain the EFFICIENCY and SAFETY of
this appliance, we recommend:

l use only the MANUFACTURER Service
l use only ORIGINAL Spare Parts

Close-up View (control panel)

E

B

A

ON - OFF Button

ON - OFF Light

Handle For Opening Door

H

F

I

C

D

"INTENSIVE 65°C" Button

"HALF LOAD" Button

Low Salt Indicator Light

Knob For Selecting Cycles

Low Rinse Aid Indicator Light

1

GB

Close-up View (Interior)

J

E

G

F

H

I

L

K

Upper Rack

T op Sprayer Arm

Rack Height Adjustor

Lower Rack

Bottom Sprayer Arm

Salt Container Cap

Washing Filter

Detergent and Rinse Aid Dispenser

Technical characteristics

Width cm. 60

Depth cm. 60

GB

Height cm. 85

Capacity 12 standard place settings

Mains water pressure 20 KPa÷ 1MPa (0,2 ÷10 bar)

Power voltage See data plate

Total absorber power See data plate

Fuse See data plate

2

Salt ......

Salt

The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and minerals
from the water .

Loading the Salt into the Softener

Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and
should be filled as follows:

1. Remove the lower rack and then unscrew and remove
the cap from the salt container;

2. If you are filling the container for the first time, fill it with
water;

3. Place the end of the funnel (supplied) into the hole and
introduce about 2 kg of salt. It is normal for a small amount
of water to come out of the salt container .

4. Carefully screw the cap back on.

Adjusting Salt Consumption

The dishwasher is designed to
allow for adjusting the amount
of salt consumed based on the
harness of the water used. This
is intended to optimize and cus­tomize the level of salt consump­tion so that it remains at a mini­mum.
Your Local Water Board can
supply the degree of hardness of
the water
in your area.
T o adjust salt consumption, pr oceed as follows:

1) Unscrew the cap from the salt container.

2) There is a ring on the container with an arrow on it (see
figure to the side), if necessary, rotate the ring in the anti­clockwise direction from the "_" setting towards the "+"
sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accord­ance with the following schema:

The salt container must be filled when the "low salt"
indicator light (located on the control panel) comes
on.

Warning: To prevent rust from forming, we advise you to
load the salt before starting a wash cycle.

Water Hardness

Salt

Clarke

degrees

0 - 14 0 - 17 0 -1,7 / 0 /

14 - 36 18 - 44 1,8 - 4,4 "-" 20 60

36 - 71 45 - 89 4,5 - 8,9 MED 40 40

>71 > 89 > 8,9 "+" 60 25

°fH mmol/l

Selector
position

consu­mption

(grams/­cycle)

Autono­my

(cycles\2­kg)

3

GB