INDESIT BDE 861483X W UK N Daily Reference Guide
Quick Guide
C
temperature °C
THANK YOU FOR HAVING PURCHASED AN INDESIT PRODUCT.
To receive more comprehensive assistance, register the
appliance on www.indesit.com/register
CONTROL PANEL
1. ON/OFF button
2. START/PAUSE button and indicator light
3. TEMPERATURE button
4. DISPLAY
5. OPTION button
6. DRYING ONLY button
7. DRYING button
8. DELAYED START button
9. SPIN button
10. WASH CYCLE SELECTOR KNOB
11. PUSH & GO button
WASH CYCLE TABLE
Prior to using the appliance, carefully read the Safety and installation instructions.
Prior to using the appliance, the bolts used for transport must be removed. For detailed
instructions on the removal procedure, consult the safety and installation instructions.
1
11
10
2 3
89
4
6
7
5
GB
Maximum load 8 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Wash cycle
Temperature
Setting Range 2 3
1 Cotton (2) 40 °C
2 Synthetics (3) 40 °C
3 Mixed 40 °C
- 60 °C
- 60 °C
- 40 °C
Max.
spin speed
(rpm)
1400 8.0 3:55
1200 4.0 2:55
1000 8.0 **
Max.
load for
washing
(kg)
Duration
(h : m)
1351 8.0 3:30
4 Eco 40-60 (1) 40 °C 40°C
1351 4.0 2:45
1351 2.0 2:10
5 White 60 °C
6 Delicates 30 °C
7 Colours 40 °C
8 Dark 30 °C
9 Antiodour 40°C
10 20°C 20 °C
11 Wool 40 °C
12 Rapid 30’ 30 °C
- 90 °C
- 30 °C
- 40 °C
- 30 °C
- 40 °C
- 20 °C
- 40 °C
- 30 °C
1400 8.0 2:45
0 1.0 **
1400 8.0 **
800 5.0 **
1000 3.5 **
1400 8.0 1:50
800 2.0 **
800 4.5 0:30
13 Wash&Dry 45‘ 30 °C 30 °C 1400 1.0 **
14 AirFresh – – – – **
15 Rinse + Spin – – 1400 8.0 **
16 Spin + Drain * – – 1400 8.0 **
Required dosage Optional dosage
1 Eco Cotton (4) 60 °C 60 °C 1400 8.0 3:45
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as the
temperature and pressure of the incoming water, ambient temperature, amount of detergent,
load quantity and type, load balancing and any additional options selected. The values given
for programmes other than the Eco 40-60 programme are indicative only.
1) Eco 40-60 (Wash) - Test wash c ycle in compliance with EU Ecodesign regulation
2019/2014. The most ecient programme in terms of energy and water consumption for
washing normally soiled cotton laundry.
Note: spin speed values shown on the display can slightly diers from the values stated in
the table.
Eco 40-60 (Dr ying)2019/2014
“Drying” option level to
consumption for washing and drying normally soiled cotton laundry. (Cycle duration: full load
9h:20’ / half load 5h:10’).
Test drying cycle in compliance with EU Ecodesign regulation
. To access “wash and dry” cycle select “Eco 40-60” wash programme and set
“ ”.
The most ecient programme in terms of energy and water
PRODUCT DESCRIPTION
1. To p
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
2.
7.
8.
Detergents and
Additives
Max.
Wash
(kg)
6.0
4.0
6.0
load for
Drying
drying
6.0
Fabric
softener
6.0
1.0
6.0
5.0
3.5
6.0
2.0
4.5
1.0
1.5 – – – – – – – –
6.0 –
6.0 – – – – – – – –
6.0
For all testing institutes:
2) Long cotton cycle: set programme 1 at temperature 40°C.
3) Long synthetics cycle: set cycle 2 at a temperature of 40°C.
4) Eco Cotton -
at a temperature of 60°C to access this cycles.
Test wash cycle in compliance with regulations 1061/2010. Set “1” wash cycle
Recommended
detergent
(****)
Residual
Liquid
Powder
dampness %
49 1.40 105 45
53 0.75 55 43
–
– – – –
53 0.77 54 33
53 0.65 52 36
53 0.45 37 33
49 0.90 90 55
–
–
–
– – – –
– – – –
– – – –
– – – –
–
–
–
–
49 0.16 90 22
– – – –
71 0.20 45 27
– – – –
– – – – – –
53 1.04 60 –
* By selecting the 16 cycle and excluding the spin cycle, the washer-dryer will drain only.
** The duration of the wash cycles can be checked on the display.
*** After programme end and spinning with maximum selectable spin speed, in default
programme setting.
DETERGENT DISPENSER DRAWER
Compartment 1:
Do not pour detergent into the compartment 1.
Detergent should only be poured into the
compartment 2.
Compartment 2: Washing detergent (powder
1.
or liquid)
3.
If liquid detergent is used, the removable plastic
partition A (supplied) should be used for proper
dosage. If powder detergent is used, insert the
partition into slot B.
4.
Compartment 3: Additives (fabric softener, etc.)
The fabric softener must never exceed the “max” level indicated on the
5.
central pin.
! Use powder detergent for white cotton garments, for pre-washing, and
6.
for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! To remove the drawer, press lever C and pull the drawer outwards.
kWh
Energy
consumption
Laundry
Total water lt
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Cotton: suitable for washing towels, underwear, table cloths,
etc. made of resistant linen and cotton that are moderately to heavily
soiled.
Synthetics: specic for synthetic items. If the dirt is dicult to remove,
the temperature can be increased up to 60° and powder detergent can be
used too.
Mixed: for washing lightly to normally soiled resilient garments in cotton,
linen, synthetic bres and mixed bres.
Eco 40-60: for washing normally soiled cotton garments declared to be
washable at 40 °C or 60 °C, together in the same cycle. This is the standard
cotton programme and the most ecient in terms of water and energy
consumption.
White: suitable for resistant linen and cotton that are heavily soiled.
Delicates: use programme 6 to wash very delicate garments. It is
advisable to turn the garments inside out before washing them. For best
results, use liquid detergent on delicate garments.
When selecting an exclusively time-based drying function, a drying cycle is
performed at the end of the wash cycle that is particularly delicate, thanks
to light handling and appropriate temperature control of the water jet.
The recommended durations are:
1 kg of synthetic garments --> 150 min
1 kg of synthetic and cotton garments --> 180 min
1 kg of cotton garments --> 180 min
The degree of dryness depends on the load and fabric composition.
Colours: a 30°C cycle that helps to preserve colours, suitable for cotton or
synthetic coloured garments. It allows for reducing electricity
consumption for heating the water while guaranteeing good washing
results. Suitable for lightly soiled garments.
Dark: use programme 8 to wash dark-coloured garments. This
programme is designed to maintain dark colours over time. We
recommend using a liquid detergent for the best results when washing
dark-coloured garments.
When you select the drying function, at the end of the washing cycle the
machine will automatically perform a delicate drying cycle that preserves the
colours of the garments. The display will show the level “ ”. Max. load: 5 kg.
Antiodour: use programme 9 for washing garments with bad odours (e.g.
smoke, sweat, fried food). The programme is designed to remove bad
odours while preserving the fabric bres. Synthetics fabrics or mixed
loads should be washed at 40°, and resistant cotton fabrics at 60°.
20°C: for washing lightly soiled cotton garments, at a temperature of 20 °C.
Wool - Woolmark Apparel Care - Blue:
The “Wool” wash cycle is approved by the Woolmark
Company for washing wool garments classied as
“hand-washable”, provided that the wash complies with
the instructions appearing on the garment’s label and
with those provided by the manufacturer of this
washer-dryer. (M1318)
Rapid 30’: this programme is designed to wash lightly soiled garments at
30° (excluding wool and silk) with a 4.5 kg maximum load in a short time:
it only lasts 30 minutes and allows for saving time and energy.
Wash&Dry 45’: select programme 13 for washing and drying lightly
soiled garments (Cotton and Synthetic) in a short time. This cycle may be
used to wash and dry a laundry load of up to 1 kg in just 45 minutes. To
achieve optimum results, use liquid detergent and pre-treat cus, collars
and stains.
AirFresh: ideal cycle to refresh garments and remove bad odours, in
particular smoke, from cotton and synthetic items in 30’ (max. 1.5 kg)
without the washing phase.
Rinse + Spin: designed for rinsing and spinning.
Spin + Drain: designed to spin and drain the water.
Eco Cotton: for washing normally soiled cotton garments at 60°C.
DISPLAY
The display is useful when programming the machine and provides a lot
of information.
B
The duration of the available wash cycles and the remaining time of a
running cycle appear in section A; if the Delayed Start option has been
set, the countdown to the start of the selected cycle will appear.
Pressing the corresponding button allows you to view either the
maximum spin speed, temperature and drying time values attained by
the machine during the set wash cycle, or the values selected most
recently (if compatible with the set wash cycle).
A
C
D
The hourglass ashes while the machine processes the data on the basis
of the selected cycle. After a maximum of 10 minutes, the icon remains
steady lit and the nal time remaining is displayed. The “hourglass” icon
will then switch o approximately 1 minute after the nal time remaining
has been displayed.
The “washing phases” relative to the selected cycle and the “washing
phase” of the running cycle appear in section B:
Wash
Rinse
Spin/ Drain
Drying
When lit, the symbol indicates that the set “Delayed Start” value has
appeared on the display.
There are three levels in section C relative to the washing options.
Section D includes the icons related to the three dierent drying levels as
well as the icon , which lights up when a timed drying option is set.
DOOR LOCKED INDICATOR
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns o before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button ; if the symbol is o, the door can be opened.
FIRSTTIME USE
Once the appliance has been installed, and before it is used for the rst
time, run a wash cycle with detergent and no laundry, by setting the
“Auto-Clean” cycle.
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
Rapid programming
- Press the ON/OFF button ; the START/PAUSE indicator light will
ash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the cycle table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER DRAWER”
section.
- Close the door.
- Press the PUSH & GO button to start the wash cycle.
Traditional programming
- Press the ON/OFF button ; the START/PAUSE indicator light will
ash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the Wash Cycle Table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER DRAWER”
section.
- Close the door.
- Use the WASH CYCLE selector knob to select the desired wash cycle: it
will be associated with a specic temperature and spin speed that can be
modied. The duration of the cycle will appear on the display.
- Modify the temperature and/or spin speed: the machine automatically
displays the maximum temperature and spin speed values set for the
selected cycle, or the most recently-used settings if they are compatible
with the selected cycle. Pressing the button gradually reduces the
temperature down to the cold wash “OFF” setting. Pressing the button
gradually reduces the spin speed until it is completely excluded (“OFF”
setting). Pressing these buttons again restores the maximum values.
- Select the desired options.
- Press the START/PAUSE button to start the wash cycle; the relative
indicator light will light up steady green and the door will lock ( symbol on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button again; the
indicator light will ash amber. If the symbol is not lit, the door may be
opened. To start the wash cycle from the point at which it was
interrupted, press the START/PAUSE button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the symbol turns on to signal that the door cannot
be opened. While a wash cycle is running, the door remains locked. To
open the door while a cycle is under way, for example, to add or remove
garments, press the START/PAUSE button to pause the cycle; the
indicator light will ash amber. If the symbol is not lit, the door may be
opened. Press the START/PAUSE button again to continue the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washer-dryer
using the START/PAUSE button (the relative indicator light will ash
amber), then select the desired cycle and press the START/PAUSE
button again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button. The cycle will be stopped and the machine will switch o.
END OF THE CYCLE
This will be indicated by the word “END” on the display; when the
symbol switches o, the door may be opened. Open the door, unload the
laundry and switch o the machine. If you do not press ON/OFF
button, the washing machine will switch o automatically after about a
10 minutes.
Loading...