RATCHET DRILL MACHINE MULTI-PURPOSE INSTRUCTION MANUAL
INTRODUCTION
NDIA'S first Tapping & Drilling Machine manufactured with latest & advance technology. It is a multipurpose
machine so it can complete the Job of Drilling & Threading simultaneously on Cast Iron Pipe, Ductile Iron Pipe,
M.S. Pipes & remaining sleeves for Drilling in Girder, Channel & Pole etc.
SAFETY INSTRUCTIONS
WARNING : When using tools, the following safety instructions must be observed to reduce
the risk of personal injury and property damage.
Please read and observe the following instructions before use.
1. Keep work area clean : An untidy and cluttered work area increases the risk of accidents
2. Use eye protection : Always use safety glasses or goggles. A face mask should also be worn
when dust is generated.
3. Wear suitable work clothes : Don't wear loose fitting clothes or jewellery. They can be caught
in moving parts and may cause injury. For outdoor work rubber gloves and non-stick footwear
are advised. Wear a protective hair net to contain long hair.
4. Guard against electric shock : Avoid any body contact with grounded surfaces e.g. bars, iron
sheet, radiators, stoves, and refrigerator enclosures.
6. Keep children away : Children should be kept away from the work area. Do not permit them to
handle the tool or tool cable.
7. Secure the work pieces : Use clamps or a vice to hold work. This will free up both hands to
operate the tool, which is safer.
8. Don't overreach when working : Keep a balanced footing at all times. Avoid abnormal stances
and awkward body positioning.
9. Do not overload or force tools : Tools operate better in the specified performance ranges.
Forcing the tool may cause damage.
10. Check for damage : Before further use always check the protection guards carefully to ensure
proper operation and performance. Check for alignment of moving parts, binding of moving
parts, breakage of parts, mountings and any other condition that may effect the tools operation.
An authorised service dealer should properly repair all damaged parts unless otherwise
indicated elsewhere in the instruction manual. Do not use the tool if the switch does not turn it on
and off.
11. Pull out power plug : When changing accessories or when the tool is not in use.
12. Avoid unintentional starting : Do not carry tools by the switch. Always check that the switch is
in the off position before connecting to power source.
13. Storage : When not in use your tools machine should be stored in a dry area, which is not
accessible to children.
14. Stay alert : Do not use the tool when you are tired. Use common sense and watch what you are
doing.
15. Remove keys and spanners : Do not forget to remove any adjustment keys, spanners and
wrenches before storing the tool.
16. Recommended use : Please note the use of tools other than those described in instruction
manuals or in the product catalogues can result in a risk of personal injury.
SINCE 1958
Page #3 M:226
RATCHET DRILL MACHINE MULTI-PURPOSE
User’s Instruction Manual
Model : P-226
Note : Before using this Ratchet Drill Machine Multi-Purpose carefully read
through this INSTRUCTIONS MANUAL to ensure efficient, safe operation. It is
recommended that these INSTRUCTIONS be kept readily available as an
important reference when using this Ratchet Drill Machine Multi-Purpose.
SINCE 1958
FEATURES:- INDIA'S first Tapping & Drilling Machine manufactured with latest & advance technology. It
is a multipurpose machine so it can complete the Job of Drilling & Threading simultaneously on Cast Iron
Pipe, Ductile Iron Pipe, M..S. Pipes & remaining sleeves for Drilling in Girder, Channel & Pole etc.
Diagram of Ratchet Drill Machine Multi-Purpose
Page #2 M:226Page #1 M:226
Prod. No 226A 226B
Weight (Kgs.) 24.0 17.5
.
Drilling/Tapping Cap. (mm/Inch.) 6- 50 (1/4 - 2) 6- 50 (1/4 - 2)
Gripping Cap. (mm/Inch) O.D. 300 (12) 300 (12)
Access. Complete Set Without sleeves &
steel box
In railway line
In sleeper of a railway track
In girder of a railway wagon
In pipe and pole of any angle In channel of any type
In over bridge
Loading...