Fig. 1
Fig. 2
Fig. 3
You have purchased the Incra Jig Ultra equipped with the
new Pro II Joinery Fence System, steel fence mounting bracket
and Incra Shop Stop. These components represent an
upgrade and are not described in the standard owner’s
manuals. The following instructions will be used in place of
the referenced instructions from the owner’s manuals.
Mounting the Incra Pro II Fence
(Replaces
Mounting the Incra Pro Fence to the Incra Jig Ultra or
Ultra Lite
from page 4 of the Incra Pro Fence System Owner's
Manual and as shown in step 2 from page 4 of the Incra Jig Ultra
Owner's Manual.)
Carefully slide the carriage into the base and pull the carriage clamp
up into the locked position. Place a 1⁄4" washer on each of the (2)
1
⁄4-20 x 1⁄2" socket head screws and insert through the slotted holes
located on the steel fence mounting bracket. Loosely thread on the
1
⁄4-20 rectangular nuts, then slide the nuts into the T-slot located on
the rear of the Pro II fence. Position the fence so that the carriage is
approximately centered on the fence length and tighten the (2)
mounting screws with the supplied hex tool, Fig. 1.
INCRA Pro II Joinery Fence System Upgrade Addendum
Installing the Extender Bar
(Replaces
Installing the Extender Bar
from page 6 of the INCRA
Pro Fence System Owner's Manual.)
Place a 1⁄4" washer on the 1⁄4-20 x 3⁄8" socket head fastener and
insert through one of the holes located at either end of the Pro II
fence. Loosely thread on the 1⁄4-20 rectangular nut and slide the
extender bar into the cavity in the fence, capturing the rectangular nut
in the T-slot located on the extender bar. The scale on the extender
bar should be face up. Slide the extender bar until only about 1" of
the bar remains exposed and tighten the fastener, Fig. 2.
Place a
1
⁄4" washer and a 1⁄8" thick nylon washer on the 1⁄4-20 x 2"
socket head screw and insert through the extruded hole located on
the extender bar stop and loosely thread on the 1⁄4-20 rectangular
nut. Slide the nut into the T-slot located on the front of the extender
bar. Slide the extender bar stop until the flat side of the stop contacts
the end of the Pro II fence. Tighten the fastener, then slide the scale
to read zero at the end of the fence extrusion, Fig. 3.
Caution:
Never allow the opposite end of the extender
bar to protrude into the cut area.
Pro II
Fence
Rectangular
nuts captured
in T-slot
Steel fence
mounting bracket
1
/4-20 x 1/2" socket
head screw with washer
Rectangular
nut captured
in T-slot
Extender
bar
1
/4-20x3/8"
socket head
screw with
washer
1"
Slide scale to
read zero here
Extender
bar stop
1
/8" thick
nylon
washer
1
/4" washer
1
/4-20x2" socket
head screw
Made by: Taylor Design Group, Inc. ■P.O. Box 810262 ■Dallas, Texas 75381 ■Web Site: www.incra.com 09-2000
Printed in the U.S.A. © 2000, Taylor Design Group, Inc. INCRA is a registered trademark of Taylor Design Group, Inc.
WARRANTY
Taylor Design Group, Inc. warrants this product for one year from date of purchase. We will repair any defects due to faulty
material or workmanship, or at our option, replace the product free of charge. Please return the failing component only,
postage prepaid, along with a description of the problem to the address below. This warranty does not apply to parts which
have been subjected to improper use, alteration, or abuse.
LIFETIME WARRANTY ON POSITIONING RACKS
If an INCRA positioning rack in this tool becomes damaged for ANY reason, Taylor Design Group will replace it free of charge
for as long as you own your tool. Return the damaged rack, postage prepaid, and allow 1 to 2 weeks for delivery.
Fig. 5
Mounting an Auxiliary Fence to your
Pro II Fence.
(Replaces last paragraph on page 8 of the Incra Pro Fence
System Owner's Manual.)
To mount the auxiliary fence to your Pro II Fence, you will need
(2) 1⁄4-20 phillips pan head screws, (2) 1⁄4" flat washers and (2)
1
⁄4-20 hex nuts. The length of the screws should be slightly less
than the thickness of the auxiliary fence. Drill two 5⁄16" through
holes in the auxiliary fence in the locations shown in Fig. 5.
Counterbore the holes with a 3⁄4" diameter bit.
Adjust the depth of the counterbore so that the screw, when
installed in the counterbore with the 1⁄4" washer, extends 3⁄8"
through the back of the auxiliary fence. Loosely thread on the
1
⁄4-20 hex nuts, then slide the hex nuts into the T-slot located on
the front face of the Pro II Fence. Tighten the machine screws
to secure the auxiliary fence.
Fig. 4
When not in use, the extender bar and stop can be
stored in the fence. Just slide the extender bar out, turn it
over so that the scale is face down, and insert back into
the fence. Tighten the fastener to secure the bar, Fig. 4.
28"
14"
7"
1 3/4"
5
/16" dia. through hole
3
/4" dia. counterbore
Extender bar
inverted for
storage
Loading...