Taylor Design Group, Inc.
warrants this product for one
year from date of purchase.We
will repair any defects due to
faulty material or workmanship,
or at our option, replace the
product free of charge. Please
return the failing component
only, postage prepaid, along
with a description of the
problem to the address below.
This warranty does not apply to
parts which have been
subjected to improper use,
alteration, or abuse.
OWNER’S MANUAL
Warranty
Please read this owner’s
manual before use and keep
it at hand for reference.
Safety
Important safety instructions for using the INCRA Miter1000
■
Before using the Incra Miter
1000
, read and follow all of the instructions and
safety information in this owner's manual.
■
When using the Incra Miter
1000
in conjunction with any other tool, first read
and follow all instructions and safety information in that tool's owner's manual.
■
Never let the saw blade come in contact with the aluminum or steel
components of the INCRA Miter
1000
.
■
When using the INCRA Miter
1000
, always keep your hands clear of the saw
blade and the line of cut.
■
Always turn off the power and make sure that the saw blade comes to a
complete stop before changing the setting of any part of the INCRA Miter
1000
.
■
Always securely tighten the large black clamping knob before starting any cut.
■
Wear safety glasses, hearing protection, and follow all normal shop safety
practices
■
After making any adjustments to the miter angle or fence position of your
INCRA Miter
1000
, always verify safe clearance between the blade and fence
before turning on the saw
■
After making any adjustments to the fence position on the INCRA Miter
1000
,
always make sure that the two socket head screws are securely tightened
■
When using the sliding stop to position a piece for a cut, always hold or
otherwise clamp the board between the stop and the blade.
®
2
Remove the hex bolt that secures the protractor head
and replace with the large threaded knob included in
the hardware pack. The washer on the hex bolt must
be used with the threaded knob, Fig. 1.
FIG. 1
Assembly
The method used to join the fence mounting
bracket to the protractor head makes it easy to
fine-tune the fence perfectly perpendicular to your table
top. To adjust, loosen the (3) #10-24 socket head
screws that secure the bracket and slide a paper or
plastic shim between the bracket and the protractor
head. Placing the shim behind the screws will
decrease the angle. Placing the shim in front of the
screws will increase the angle.
Using the (2) #10-32 x
1
⁄2" thumbscrews with
washers and hex nuts, slide the stop positioner into
the T-slot located on the front face of the fence.
Tighten the fasteners, Fig. 4.
Place the INCRA Miter
1000
in the left hand miter slot
of your table saw. Loosen the (2) 1⁄4-20 socket head
screws that secure the fence to the fence mounting bracket
and slide the fence to a position that leaves safe clearance
between the end of the fence and the blade. Tighten the (2)
1
⁄4-20 fasteners, Fig. 3.
If the Miter slot in your table saw has a T-slot, attach the
T-clip to the end of the miter bar as shown in Fig. 2.
FIG. 2
FIG. 3
1
2
3
FIG. 4
Threaded
knob
Washer
Remove
hex bolt
1
⁄4-20 socket
head screws
Position for
safe clearance
between
fence and
blade.
#10-24 x
1
⁄4"
phillips flat
head screw
T-clip
#10-32 x
1
⁄2"
thumbscrew
Stop
positioner
#10 washer
Slide hex nuts
into T-slot
Squaring the fence to your table saw top
Miter bar
Note: The remaining (2) #10-32 x 3⁄4" phillips screws,
washers, and hex nuts in your hardware pack are
provided for future use in attaching a wooden zeroclearance auxiliary fence. See page 4 for information on
making and using a wooden subfence.
3
Adjust the Miter Bar
Adjust the miter bar at each of the (6) expansion
mechanism locations for a good fit in your table saw's
miter slot. Turning the screw clockwise expands the
mechanism. You'll find (3) of the expansion locations in front
of the fence and (1) underneath the fence. (You'll need to
remove the fence for access.) Adjust these (4) front
expansion points first, expanding a little at each of the
locations until the bar slides smoothly, Fig. 5.
Adjust Fence Mounting Bracket 90° to Saw
Blade
Set the protractor head to read 0°, engaging the tooth
on the actuator firmly into the 0° notch on the protractor
head, Fig. 7. Tighten the large clamping knob and the
small actuator thumbscrew.
Using the supplied
5
⁄32" hex key, loosen the (3) #10-24 x
5
⁄16" socket head screws that secure the fence mounting
bracket to the protractor head. Unplug your table saw, then
use a reliable machinist square to set the fence at 90° to the
saw blade, Fig. 8. Tighten the (3) socket head screws.
This one-time calibration prepares your INCRA Miter
1000
for
work in either miter slot. Just remember that the accuracy of
the INCRA Miter
1000
at any subsequent setting is dependent
upon the accuracy of your initial 90° calibration. Verify this
calibration with a test cut and fine-tune as necessary.
Zeroing the Sliding Stop to the Blade
Set the protractor head to 0° and clamp the sliding
stop to the fence about 10" from the blade. Crosscut a piece
of scrap stock with this setup and measure the resulting cut.
Slide the scale on the fence to read this measurement under
the cursor. Fig. 9.
Note: To zero the stop for angles other than 90°, the test cut
must be made at the selected angle.
1
Calibration
2
FIG. 5
Finally, remove the large clamping knob and pivot the
protractor head to gain access to the (2) rear expansion points,
Fig. 6. Replace the fence, clamping knob, and washer.
FIG. 6
FIG. 7
3
FIG. 8
FIG. 9
Square
fence to
blade
Fence removed
for access
Adjust (4)
front expansion
points
Remove knob
and rotate
protractor
head for
access
Adjust (2) rear
expansion points
Actuator
thumbscrew
Actuator tooth engaged at 0°
Measure test cut length
Slide scale to read
board’s length
under cursor
Loosen (3) socket
head screws
4
Five-degree Indexing
(including 22.5° and 67.5° settings)
Loosen the actuator thumbscrew and pivot the
actuator tooth away from the notches located on the
perimeter of the protractor head. Loosen the large clamping
knob, Fig. 10.
Rotate the protractor head and fence to the desired
angle, then firmly engage the tooth on the actuator
with the corresponding notch on the protractor head.
The actuator tooth should point directly to the desired angle
on the scale. Tighten the large clamping knob, then tighten
the actuator thumbscrew, Fig. 11.
Operation – Changing Angle Settings
1
2
FIG. 10
FIG. 11
Pivot actuator
tooth away from
protractor head
Large
clamping
knob
Actuator
thumbscrew
Tighten large
clamping knob
then tighten
actuator
thumbscrew
Actuator tooth,
firmly engaged with
notch on
protractor head
Continuous Adjustments (for angle settings
finer than 5° increments)
Pivot the actuator tooth away from the notches on the
protractor head, aligning the arm over the miter slot, and
tighten the thumbscrew. Now loosen the small nylon
thumbscrew on the actuator and pivot the 1⁄2 ° cursor toward
the scale. Rotate the cursor until it is aligned edge to edge
with the scale and tighten the thumbscrew. When you change
miter angles, just align the desired angle on the scale with the
“0” cursor line. For 1⁄2 ° adjustments align the mark on the
scale with the “.5” cursor line. Fig 12.
FIG. 12
FIG. 13
Adding a wooden subfence to the front of the MITER1000
fence is easy to do and offers several benefits. You can
extend the length or height of the standard fence, and by
extending the subfence to cross the line of cut, it provides
zero clearance backing for tearout control. Use the drill and
counterbore dimensions shown in Fig. 13. Adjust the height
and length to match your applications. Fasteners are
provided in your hardware pack.
Attaching Auxiliary Fences
Made in America by: Taylor Design Group, Inc.
P.O. Box 810262, Dallas, Texas 75381, 972-418-4811, www.incra.com
Printed in the U.S.A. © 2000, Taylor Design Group, Inc.
INCRA is a registered trademark of Taylor Design Group, Inc.
08-2000
Pivot actuator tooth away from
protractor and tighten thumbscrew
#10-32
hex nut
3
⁄4"
1
⁄4" thru hole with
5
⁄8" dia. x 5⁄16" deep
counterbore
#10flat
washer
#10-32
machine
screw
Cut to
desired
height
9
⁄16"
Arm aligned
with miter
slot
Pivot cursor to scale
To increase holding power when crosscutting or
mitering, add a strip of adhesive backed sand
paper to the front face of your wooden auxiliary fence.
Use 150 to 180 grit sandpaper.
Caution:
After making any
adjustments to the miter angle of your
INCRA Miter1000, always verify saf
e
clearance between the fence and the blade
bef
ore turning on the saw.
Loading...