Standard Frame Installation
1
Guide
Code
Picture
Qty
A
Side
Bracket
(A)
2
B
Side
Bracket
(B)
2
C
Lifting
Column
2
D
Support
Brackets
2
2
Code
Picture
Qty
E
End
Brackets
2
F
Feet
2
G1
Coned
M6X15
12
G2
Straight
M6X15
8
3
Code
Picture
Qty
H
M10X25
Screws
8
I
Allen Key
Guides
12
J
Allen Key
1
K
Control
Box
1
L
Keypad
1
4
Code
Picture
Qty
M
Wood
Screws
12
N1
Control
Box
Screws
2
N2
Keypad
Screws
3
O
Cable Ties
10
P
Cable
Sleeve
1
5
1. Insert the Allen Key Guides (Part I) into the holes in Parts A and B.
6
2. Attach one, part A and one, part B to each lifting column (part C) using the
Coned M6x15 socket head cap screws (Part G1). Reference the picture below.
3. Remove end bracket (part E) from carton. Attach one (1) end bracket (part E)
to each column (part C) using the Coned M6x15 socket head cap screws (part
G1). Reference the picture below.
4. Remove the feet (part F) from the carton. Attach one (1) foot (part F) to each
7
lifting column (part C) using the Straight M6x15 socket head cap screws (part
G2). Reference the picture below.
5. Insert the support brackets (part D) into the side brackets (part A & B).
Loosely insert support screws (part H). Do not tighten until after step 6.
6. Align the holes of the assembled frame with the corresponding holes in the
8
worksurface. Screw the assembled frame into the worksurface using the
wood screws (part M). Do not fully tighten screws until each one is started.
7. Tighten support bracket screws (part H) mentioned in step 5. Do not
overtighten the screw.
8. Place the control box (part K) in between the support brackets (part D) on the
work surface. Ensure that the control box (part K) is orientated so that the
power cord is facing the nearest lifting column (part C). Screw the control
box (part K) into the worksurface using the control box screws (part N1).
Reference picture below to ensure proper alignment and installation.
9. Align the holes of the keypad (part L) with the holes of the worksurface.
Screw the keypad (part L) into the worksurface using the keypad screws (part
N2). Reference the picture below.
10. Peel and stick the Cable Tie’s (part O) on the worksurface to keep all cables
10
from dangling below desk. Reference the picture below for help in where to
place cable ties.
11. To use the cable sleeve (part P), start near the worksurface and wrap all wires
all the way to the outlet or power strip.
Keypad Operation
Step
Operation
Motion
1.
Press and Hold &
simultaneously for more than
3 seconds
Legs begin to move
down at half speed of
normal operation
2.
Keep Pressing &
Legs move down to the
lowest positions and
rebound 2-5mm, then
stop
3.
Release & Together
Initialization is
Completed
Step
Operation
Motion
1.
Press and Hold
Legs Move Up
2.
Release
Legs Stop
3.
Press and Hold
Legs Move Down
4.
Release
Legs Stop
Step
Operation
Motion
1.
Press and Hold or then
Release at Desired Height
Run the Legs to the
Position You Want
2.
Press Button S, then Press
Button 1, 2, or 3, Within the
Next 3 Seconds
Position 1, 2, or 3 is
Now Saved
Step
Operation
Motion
1.
Press and Hold the Button 1,
2, or 3
Legs Return to the
Corresponding Position
Saved
11
Initialization Procedure
*The initialization procedure must be completed before operation as soon as the
table is installed, or parts are replaced.
Move Up and Down
Set Memory Positions
Move to the Memorized Positions
Move to the Memorized Positions
Step
Operation
Motion
1.
Press and Hold the Button
1, 2, or 3
Legs Return to the Related
Position Saved
Step
Operation
Motion
1.
Press and Hold Button S,
then Press and Hold for
about 3 Seconds
The Height Information will
be Changed Between
Centimeters and Inches
2.
Release the Buttons
Completed
Step
Operation
Motion
1.
Set the Table at any Height,
Recommended at the
Bottom Position
Measure the Actual Table
Height. Write Down the
Number (In or Cm)
2.
Press & Hold Button S, then
Press & Hold for 3 seconds
The First Number Starts
Flashing on Screen
3.
Release the Buttons, Then
Press or to Change the
First Number
The First Number is Being
Increased or Decreased to
the First Number Measured
4.
Press Button S
The Second Number Starts
Flashing on Screen
5.
Press or to Change the
Number
The Second Number is Being
Increased or Decreased to
the Second Number
Measured
6.
Press Button S
The Third Number Starts
Flashing on Screen
7.
Press or to Change the
Number
The Third Number is Being
Increased or Decreased to
the Third Number Measured
8.
Press Button S
Completed
12
Toggle the Display Unit Format
*Minimum height variation: Inches: 0.5in. Centimeters: 1cm.
How to Verify the Keypad Data to Actual Height
*Ensure you are using desired units of measurement (in or cm).
Lock the Stroke
Step
Operation
Motion
1.
Press and Hold or , then
Release
Run the Legs to Desired Table
Surface Height Position
2.
Press and Hold Button S,
then Press and Hold 1 for
about 3 Seconds
Letter “-L-” is Indicated on the
Screen. That means the
Position is Locked at the
Lowest Position that the Table
can be Moved to
3.
Release the Buttons
Completed
Step
Operation
Motion
1.
Press and Hold Button S,
then Press and Hold 2 for
about 3 Seconds
Letter “-C-” is Indicated on the
Screen. That means the Table
is Now Unlocked and Can be
Moved in Full Range
2.
Release the Buttons
Completed
13
*Legs are not able to run below the locked position. Memory Position(s) below
the locked position will be lost even after the table is unlocked, you need to
follow SET MEMORY POSITIONS again to reset these memory positions.
Unlock the Stroke
Troubleshooting
Fault Phenomenon
Solution
After Connecting the Power,
Press or , and the Legs Have
no Response
1. Re-initialize the Table
2. Check if Connection is Correct
3. Contact Direction Desk
Table Worked a Couple Times,
Now No Longer Moves Up or
Down
1. Re-initialize the Table
2. Unplug Power Source, wait 3 Seconds,
Plug Back In
3. Ensure All Cables are Properly
Connected
4. Contact Direction Desk
One Leg Moves While the Other
Does Not
1. Check Connections
2. Ensure Excess Weight is Not Placed on
One Leg
3. Contact Direction Desk
Tables Slides Down Itself
1. Check if the Weight of the Load on
Table Exceeds 220lbs
2. Contact Direction Desk
Error Code E01 (Leg Error)
1. Assure the Leg Cable is Plugged
Securely into the Control Box
2. Re-initialize the Table
3. Contact Direction Desk
Error Code E02 (Over-Use)
1. Wait 15min Prior to Further Use
Error Code E03 (Weight
Overload)
1. Remove Weight from the Table
Surface
Error Code E04 (Data Error)
1. Re-initialize the Table
Error Code E05 (Stuck Button)
1. Check the Condition of the Button on
Keypad
2. Contact Direction Desk
Error Code E06 (Communication
Interruption)
1. Check the Cable Connection Between
Keypad & Control Box
2. Verify that Cable is Plugged In
3. Contact Direction Desk
Error Code E07 (Keypad Error)
1. Height of Table was Incorrectly Set
2. Re-initialize the Table and Reset
Desired Memory Height
14
Loading...