Inaxsys COAX2IP User Manual

10/100Base-Tx Long Reach

Ethernet Extender

BNC

User Manual

Introduction

Long Reac

h Ethernet Extender with one
Ethernet port (on 1 RJ-45 connector) and one
VDSL port on 1 BNC connector. This is a bridge
mode modem accommodating Ethernet and
VDSL technologies to extend Ethernet over
single-pair phone line by using a VDSL signal.
Up to 100/60 Mbps (or 90/90 Mbps with
synchronous data rate) transition bandwidth
within 300m and 40/10 Mbps for 1km long range
connections provides ultra-high performance to
the pervasive telephone line network. Its
plug-n-play solution minimum installation time &
cost by allowing video streaming and data to
share the same telephone pair without
interference.

With one DIP switches configuration, the
product includes the CO (Central Office) site
and CPE (Customer Premise Equipment) site.
The long distance support feature makes this
extender be a great and ideal solution for FTTx
(Fiber to the Building, Fiber to the Campus or
Fiber to the Home) applications. It supports high
bandwidth VDSL2 over existing telephone wires
in the “last mile” from the ISP / Telecom /
Service provider’s fiber mode to the buildings
and customers’ home.

Key Features



1 full-duplex VDSL links via BNC

connector

 Selectable CO and CPE mode

 Selectable fast and interleaved mode

 Selectable target SNR margin

 Compliant with ETSI, IT

U and

ANSI standards

Front Panel (LEDs)

LED Indicators

LED Status Description

Duplex

On RJ 45 port full duplex

Off RJ 45 port half duplex

Speed

On RJ 45 connect at 100M

off RJ 45 connect at 10M

Link/Act

On RJ 45 port is link

Blinking

RJ 45 port Data is
transmitting or receiving

Power

On Power is on.

Off Power is off.

CO

On

Work as Master at Core
center

off

Work as CPE at Edge
site

Nego

/Link

/Act

Blinking Negotiation

On Link is connected

flash

Blinking

Data

Active

DIP Swi

tches Mode Configuration

DIP 1 2 3 4

On CO Fast 998ISDN 6dB

Off CPE Interleave Symmetric 9dB

 Pin 1 CPE or CO mode selection

 Pin 2 Interleave mode or

fast mode selection

 Pin 3 Symmetric ISDN Mode or

998 ISDN Mode selection

 Pin4 Signal Noise Rate selection

for 9dB or 6dB

Package Contents

Before yo

u start to install this switch, please
verify your package that contains the
following items:

 One Long Reach Ethernet Extender
 One Power Adaptor
 One User Manual

Note: If any of these items is found missing
or damaged, please contact your local
supplier for replacement.

COAX2IP

Mechanical

Technical Specifications

Standards

IEEE802.3 10Base-T
IEEE802.3u 100Base-TX
IEEE802.3x Full Duplex
ETSI
ITU
ANSI
Full ITU-T G.993.1 (VDSL)
compatible
G.997.1 compatible.

BNC for coaxial cable)

Interface

RJ-45 female Ethernet jack

Switching Method Store and Forward

LED
Indicators

Duplex
Speed
Link / Act
Power
Master
Link / Negotiation

Power Input

DC 5V/2A

Dimensions

102 × 75 × 23 mm

(L x W x H)
Weight 0.28 kg
Operating
Temperature

0 to 45℃

Storage
Temperature

-20 to 90℃

Humidity

10 to 90% RH

(non-condensing)
Certifications FCC Class A, CE

FCC Warning

This device has been t

ested and found to
comply with limits for a Class A digital device
and pursuant to Part 15 of FCC Rules.
These limits are designed to provide a
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This equipment
generates and radiates radio frequency
energy. If it’s not installed and used in
accordance with the user’s manual, it may
cause interference. In which case, users will
be required to correct interference at their own
expenses.

CE Warning

This is a Class A product

. In a domestic
environment, this product may cause radio
interference in which case the user may be
required to take adequate measures.

8272 Pascal Gagnon, Saint-Leonard, Quebec, Canada, H1P 1Y4, www.inaxsys.com