Imtra LIM80110, ILIM80200, LIM80102 Reference Manual
PowerLED Dimming Control
Reference Manual
ILIM80110
Imtra PowerLED Dimmer
(see page 3)
ILIM80102
Captiva PowerLED Dimmer
(see page 4)
ILIM80200
PowerLED Analog Dimmer
(see page 5)
PWM Control of PowerLED Lights
thru a centralized lighting control
system
(see page 6)
Overview
In order to provide control of our PowerLED lighting fixtures to support
various lighting applications, Imtra offers a range of dimming control
solutions.
For typical applications, an ILIM80110 dimmer module may be used with
any number of normally open momentary pushbuttons to control up to 30*
PowerLED lights.
Lighting circuits that include one or more Captiva PowerLEDs require an
ILIM80102. This dimmer module can also be controlled by any number of
normally open momentary pushbuttons and it can control up to 50*
PowerLED lights.
For applications where it is necessary to integrate with a third party
automated control system, one of two solutions may be employed.
1. A 0-10V analog signal may be used to control the PowerLEDs via
our ILIM80200 dimmer module. This dimmer module requires a 010V analog signal source and can control up to 30* PowerLED
lights.
2. A Pulse Width Modulating signal may be used to control the
PowerLEDs directly via the white and grey dimming signal wires.
Specifications
ILIM80110 ILIM80102 ILIM80200
Height 0.90” (23mm) 0.84”(21mm) 0.63” (16mm)
Width 3.86” (98mm) 2.53”(64mm) 2.63” (67mm)
Depth 2.10” (52mm) 1.47”(37mm) 1.38” (35mm)
Input Voltage Range 10-30VDC
Max. Output Current 0.03A 0.05A 0.03A
Capacity 30 Fixtures* 50 Fixtures* 30 Fixtures*
Control Interface N.O. Contacts N.O. Contacts 0-10V Analog
IP Rating IP40
*Note: Exceeding maximum number of fixtures can permanently damage
dimmer module.
1
2
Imtra PowerLED Dimmer
V
V
Captiva PowerLED Dimmer Module
The ILIM80110 PowerLED Dimmer Module is used to
manually operate a circuit of PowerLED Lights with on/off and
dimming control. Before making any connections, be sure all
power in the circuit is turned off at the breaker. To install
your PowerLED dimmer, connect the wires according to the following
wiring schematic. Failure to follow the wiring schematic exactly as shown
will result in failure & permanent damage to the dimmer.
ILIM80110
Dimmer Module
Momentary
Pushbutton
Momentary
Pushbutton
Imtra
PowerLED
Imtra
PowerLED
To other
control
push
buttons
To other PowerLEDs
(up to 30 total)
oltage Supply
(battery, converter, etc)
To operate your PowerLED Dimmer Module and Lights:
Tap any one of the momentary pushbuttons to turn on or off.
Press and hold any one of the momentary pushbuttons to dim up
or down.
Note:
When DC voltage to the PowerLED Dimmer and Lights is lost, the
default setting when powered up again is always off.
A tap of the momentary pushbutton will always turn the PowerLED
Dimmer and Lights on to the previous setting.
The ILIM80102 Captiva PowerLED Dimmer Module is
specifically designed to control the Captiva PowerLED
down spot. However, it may also be used to control a
circuit which contains both Captiva and Hatteras PowerLED
down spots. Before making any connections, be sure all
power in the circuit is turned off at the breaker. To install your dimmer,
connect the wires according to the following schematic. Failure to follow
the wiring schematic exactly as shown will result in failure & permanent
damage to the dimmer.
ILIM80102
Dimmer Module
Captiva
Momentary
Pushbutton
Momentary
Pushbutton
PowerLED
Other
PowerLED
To other
control
push
buttons
To other PowerLEDs
(up to 50 total)
oltage Supply
(battery, converter, etc)
To operate your Captiva PowerLED Dimmer Module and Lights:
Tap any one of the momentary pushbuttons to turn on or off.
Press and hold any one of the momentary pushbuttons to dim up
or down.
Note:
When DC voltage to the PowerLED Dimmer and Lights is lost, the
default setting when powered up again is always off.
A tap of the momentary pushbutton will always turn the PowerLED
Dimmer and Lights on to the previous setting.
3
4
Loading...