1
High Output Flexible Strip Tape
Installation and Operation Manual
2
Overview
HO (High Output) Flexible LED Strip Tape is a linear array of high power
LEDs encased in a flexible, clear epoxy resin (interior version) or in a clear
silicone UV protected sleeve (exterior version). The thin diameter and
extremely low profile form factor allow these products to be installed in
areas too confined for traditional rope light products. A linear array of wide
angle SMD LEDs results in homogenous and even light distribution without
shadows or gaps. For mounting ease, the interior version is supplied with
3M double sided tape already installed on the product. The exterior version
is secured using flexible silicone clips. Each cut section comes with wire
leads so your LED Strip Tape is ready to connect to your DC power source.
HO Flexible LED Strip Tape may be cut to suit every 4" (12V version) or
every 6" (24V version).
Applications
Cove Lighting • Courtesy Lighting • Under Gunnels • Under Cabinets •
Stairs • Closets/Lockers • Architectural & Landscape
Specifications
Input Voltage 12V 24V
Input Power 1.90 watts per foot 2.44 watts per foot
Luminous Flux
46 lms per foot
151 lms per meter
59 lms per foot
194 lms per meter
Viewing Angle
140°
Bulb Spacing 1.3’ (330mm) 1.0” (25mm)
Cutability Every 4” (102mm) Every 6” (152mm)
Tape Dimensions (H x W)
3.52mm (0.14”) x 10.20mm (0.40”) – standard
5mm (0.20”) x 14.20mm (0.56”) - exterior
Maximum Run 19.7’ (6 meters) 31.5’ (9.6 meters)
Ingress Protection IP65
* IP65: “Protected from the ingress of dust and low pressure jets of water from all directions”
3
Wiring Instructions & Installation
The Strip Tape section is
pre-wired with POS &
NEG wire leads. The
grey wire is soldered to
the negative side and the white wire is soldered to the positive side.
Double check by looking for the “+” and “-“ printed on the circuit board.
Not observing polarity can damage the product.
1. Before making any connections, turn power completely off.
2. Before installing or making permanent connections, first test the
product to make sure it is operating correctly.
3. Ensure the area of installation is free of dirt, dust, oil or silicones. Avoid
cleaners that leave behind residue or wax. A solvent such as Acetone
can be used but read the label carefully as it can damage some
surfaces.
4. Measure off area and determine if your section of Strip Tape will need
to be shortened. Using sharp scissors, you may cut on the marked lines
which are located every 4” (for 12V product) or every 6” (for 24V
product) between solder pads. If cutting the exterior (silicone jacket)
version, you must seal the cut end with an End Cap and silicone. End
Caps are available as an accessory item from Imtra.
5A. For the interior (clear epoxy) version, peel off the 3M tape form the
backside of the Strip Tape. Place the Strip Tape on the contour and
gently press down allowing the Strip Tape to firmly attach to the
surface.
5B. For exterior (silicone jacket) version, use the flexible silicone mounting
clips to secure strip tape in place.
6. Make connection using approved connectors (avoid the use of wire
nuts). Use shrink tube in wet/damp areas.
7. Turn power back on to test.
HO Strip Tape for Interiors – Epoxy coated, installs with 3M self-adhesive tape
HO Strip Tape for Exteriors – Clear silicone sleeve, installs with flexible silicone clips
Silicone mounting clip
for exterior version
Cut mark
4
Safety Information & Recommendations
1. The strip itself and all its components should not be mechanically
stressed.
2. Assembly must not damage or destroy conducting paths on the circuit
board.
3. Parallel electrical connection is highly recommended as safe electrical
operation mode.
4. Serial connection is not recommended. Unbalanced voltage drop can
cause hazardous overload and damage the pcb.
5. If using a power supply or LED converter, be sure to size for the
appropriate load.
6. Pay attention to standard ESD (Electrostatic Discharge) precautions
when installing.
Power Sources
Our low voltage (12VDC or 24VDC) Flexible LED Strip Tape is designed for
use with hard-wire DC hook-ups. If stepping down voltage from a 120/230V
source, a standard low voltage AC transformer will damage the product.
You must use a regulated DC power supply or a voltage-regulated LED
converter for this purpose. Imtra carries a full range of voltage regulated
LED Converters. See our website for more information.
Our Led Strip Tape performs optimally with constant voltage at or near the
specified voltage input. It is sensitive to over-voltage and transient spikes,
therefore long term performance is directly dependent on the input voltage
provided. For DC installation on boats, a power conditioner or voltage
stabilizer is recommended for maximum life of the product. Imtra
Corporation carries a range of Power Conditioners. See our website for
more information on these products.
Product Support
If you have any questions or need to return product for any reason, please
contact Imtra directly by phone at (508) 995-7000 or by email at
info@imtra.com.
30 Samuel Barnet Boulevard, New Bedford, MA 02745
(508) 995-7000 • www.imtra.com
Loading...