IMTEC Sprite User Manual

Download

Sprite User's Manual

Table of Contents

Introduction and Basics __________________________________________ 1

Introduction 1 Safety Information 1

Intended Use: 1

Installing and Moving Sprite 4

Pre-Installation Requirements 4 Additional Connections 4 Licensing 4 Moving Sprite 4

Safety 5

Compliance 5 Modification of Sprite 5 Safety Features 5 Procedures 6 Protection 6 Liquids 6 User Safety Symbols and Features 6 Brushed Stainless Steel 9 Exterior Cabinet 9

Touch screen 9  External Machine Diagram 9 Machine Specifications 10

Cabinet Specifications 10

X-ray System Specifications 10

Operating Specifications 11 Contact Information 11 Basic Operation 12

Powering Sprite On and Off 12

Using the Touch screen Interface 12

Required Pre-Scan Procedures 12 Sample Placement 13

Canisters and Platforms 13

Calibration Phantoms 13

Fixture/Phantom Placement 14 Contact Information 14

Components ___________________________________________________ 15

Main Screen 15

iii

Sprite User's Manual

Begin a New Scan Button 15

One Touch Scan Button 16

Utilities Button 16

Locate a Scan Button 16

Background Processing Button 17

X-ray System Maintenance Button 17

Messages 18 Begin a New Scan Screen 19

Image Area 19

Scan Settings 20

System Calibration or Validation Settings 22

Preview Image Button 22

Save Button 23

Stage Position Control 23

Scan Button 23

Scout Penetration 23

Full Imaging Scanning, System Calibration, and Validation 24 Scanning Screen 25

Scan Progress 25

Image Area 26 Scan Review Screen 27

Image Area 28

Action Button 28

Table Settings Button 28

Scan/Reconstruction Table 29

Delete 29

Copy 30

Move 30

Processing Status 30

GUID 31

Operation 31

Description 31

Comment 31

View Surface or Volume Reconstructions or Calibration/Validation Results 31 Processing Setup Screen 32

Region of Interest 32

Estimated Processing Time 34 

Processed Data Type 34

Resolution 35

Processing Button 35 Results Screen 36

Table of Contents

Image Area 36

Surface Export 37

Results Screen – Calibrations and Validations 38

Report Button 38

System Calibration and Validation Reports 38 Locate a Scan Screen 40

Scan Table 40

Page Up and Page Down Buttons 40

Search Button 41

Table Settings Button 42  Background Processing Screen 43

Reconstruction Table 43 Utilities Screen 44

System Sleep Button 44

Touch screen Calibration Button 44

System Shutdown Button 45

Storage Device Management Button 46

Network Configuration Button 48

One Touch Scan Setup Button 50

Submit Trouble Ticket Button 51

Reset Processing Engine Button 53

Reset System Board Service Button 54

Reset X-ray Service Button 54

Reset Scan Engine Button 54

System Restart Button 54 System Status Screen 55

Gauges 55

Test X-ray Lamp Switch 55

Primary Indicators 56

Log and Version Buttons 56

Note: The button that has been pressed and is actively displaying its

corresponding information turns redSecondary Indicators 56

Secondary Indicators 57 X-ray System Maintenance Screen 58

Begin Conditioning Button 58

Begin Detector Calibration Button 59

Scheduled Maintenance Button 59 Common Elements 61

Abort Button 61

Arrow Button 61

Image Manipulation Buttons 61

Sprite User's Manual

Navigation Buttons 62

Turn X-rays Off Button 63

Background Processing Button 63

Scan Identification 64

Keyboard 64

Kilovolts Icon 65

Milliamperes Icon 65

Status Light and Message 65

Temperature Gauge 66

X-ray Icon 66

Trefoil 67

Technical Support ______________________________________________ 69

Introduction and Basics

Introduction

Welcome to the Sprite CT scanner by IMTEC™, a 3M Company. Sprite is a sleek, compact, state-of-the-art CT scanner allows you to easily scan an object and

produce a 3D image for numerous applications. Sprite uses advanced X-ray technology and the innovative FlashCT™ software developed exclusively by IMTEC engineers to create a unique CT scanner well above industry standards. Sprite is designed with the user in mind, featuring progressive technology, excellent results, and ease of use.

Sprite's user-friendly X-ray scanning technology includes:

• a touch screen with simple software in an imbedded computer for viewing your 3D images,

• straightforward ways to ensure accurate scans,

• one-touch scanning,

• automatic conditioning and calibration, and

• a compact profile and small footprint.

Safety Information

Please read, understand and follow all safety information contained in these instructions prior to the use of this scanner. Retain these instructions for future reference.

Intended Use:

The Sprite CT scanner by IMTEC™, a 3M Company creates a 3D visualization of a scanned object through X-ray computed tomography (CT). Sprite is intended for use by trained individuals to retrieve, process, render, review, store, and distribute images. The user should be trained in the safe operation of this scanner including instruction for adherence to local radiation protection guidelines. If this scanner is used in a manner not specified, the protection provided by the equipment may be impaired.

Explanation of signal word consequences

Indicates a potentially hazardous situation, which, if not avoided, could result

WARNING

CAUTION

NOTICE

in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury Indicates a potentially hazardous situation, which, if not avoided, may result in

property damage.

Sprite User's Manual

Summary of device labels containing safety information

WARNING

Risk of Danger Refer to Manual

WARNING

Risk of Shock

CAUTION

X-ray Hazard

WARNING

Hazardous Voltage

CAUTION

X-ray Hazard (Canada)

Introduction and Basics

WARNING

To reduce the risk associated with hazardous voltage:

• do not service this scanner – there are no user serviceable parts. Use only 3M authorized service personnel,

• do not modify this scanner,

• disconnect power cord when the scanner is not in use and while cleanin g, and

• do not use a damaged power cord.

To reduce the risks associated with hazardous voltage and property damage:

• do not expose the instrument to liquids, and

• do not spray any liquid into the instrument.

To reduce the risks associated with fire and explosion:

• do not place flammable or explosive liquids in the scanner.

To reduce the risk associated with fire and property damage:

• do not use disinfecting or cleaning solvents to clean the scanner.

CAUTION

To reduce the risks associated with radiation:

• read, understand and follow radiation protection guidelines as defined by local regulation.

To reduce the risks associated environmental contamination:

• follow applicable regulations when disposing of this scanner, specifically the X-ray source assembly, all electronic circuits including replacement parts.

NOTICE

To avoid damage to scanner:

• always us a sealed container when scanning liquids.

Sprite User's Manual

Installing and Moving Sprite Pre-Installation Requirements

Please follow these conditions when preparing for Sprite's installation:

• must be placed on a flat, level surface,

• footprint is 59" wide by 24" deep,

• weighs 800 lbs,

• should be in a location where it will not be bumped or physically disturbed,

• have a local area network (LAN) Ethernet outlet available (if you choose to network

Sprite),

• and have a dedicated 208-240VAC 50/60Hz electrical circuit.

Sprite is a cabinet X-ray system, consult local and state agencies for specific requirement s for Xray facilities.

Installation will take place by an IMTEC technician.

Additional Connections

Sprite is equipped to install an external X-ray warning light or signal (the mating connecto r is supplied upon delivery). A connection is available on the back of the system that is a Normally Open contact that closes when X-rays are activated and is rated up to 240VAC and 3 A capacity.

There are two RJ-45 Ethernet ports located and labeled on the back of the system. One is for connection to an external workstation, and the other for connection to a local area network (if available).

Sprite has three 2.0 capable USB ports located on the system. They are located on the system as follows:

• On the front of the cabinet, on the right side just under the top door, to the right of the Emergency Stop button. This port provides for the easy export/import of scan data (via a USB flash drive, for instance).

• Two USB ports are located inside the lower Sprite cabinet on the left wall of the top right shelf. These ports are intended for connecting external USB hard drives only.

Two IEC power sockets are located next to the USB ports inside the lower Sprite cabinet. These sockets are exclusively intended to supply power to a maximum of two external USB hard drives. The sockets output the same AC power used to supply the system (208-240VAC 50/60Hz) and the current capacity is a total of 3 A combined between the two outlets.

Licensing

The IMTEC technician will establish Software licensing during installation and setup.

Moving Sprite

After Sprite has been professionally installed, you may need or want to move the machine. We encourage you to contact us before doing so.

Introduction and Basics

Safety Compliance

Sprite complies with all federal regulations for cabinet X-ray equipment set forth in the Code of Federal Regulations (revised 2008) by the U.S. Food and Drug Administration's Center for Devices and Radiological Health (see 21CFR1020.40). Sprite also complies with UL 61010-1 (Electrical Equipment for Measurement, Control, and Laboratory Use; Part 1: General Requirements, Underwriters Laboratories). This Class A digital apparatus complies with Canadian ICES-003. [Cet appareil numerique de la classe (*) est conforme a la norme NMB-003 du Canada.]

Modification of Sprite

FCC ID: DGFESPE130 IC: 458A-ESPE130 Modifications to this device shall not be made without the written consent of the 3M Company.

Unauthorized modifications may void the authority granted under federal Communication s Commission and Industry Canada rules permitting the operation of this device.

Please be advised that the U.S. Food and Drug Administration's Code of Federal Regulations for ionizing radiation emitting products states:

"The modification of a cabinet X-ray system previously certified pursuant to 1010.2 by any person engaged in the business of manufacturing, assembling or modifying ca binet X-ray systems shall be construed as manufacturing under the act if the modification affects an y aspect of the system's performance for which this section has an applicable requirement. The manufacturer who performs such modification shall recertify and reidentify the system in accordance with the provisions of 1010.2 and 1010.3 of this chapter."

U.S. Food and Drug Administration. Code of Federal Regulations. 2008. Title 21, Volume 8. 21CFR1020.40.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Safety Features

Emergency Stop Button

Pushing this button physically disconnects the power to both the X-ray source and the motion stages. This button is located on the front of the top door.

X-ray Shutoff Buttons on the Touch Screen

You may stop a scan by tapping the Abort button or by holding down the Turn X-rays Off button (or, as mentioned above, by pressing the Emergency Stop button located on the front of the top door.

Sprite User's Manual

Interlock System

The interlock system is a safety mechanism that protects the operator from active X-rays. The lock is in place in accordance with 21CFR1020.40.

The interlock system automatically locks the door when X-rays are turned on. You will not be able to open the door until the X-rays are turned off, at which point the interlock system unlocks the door.

Key Switch

The key must be inserted and rotated for X-rays to be enabled. The key switch is located on the front panel of the electronics box.

Procedures

Sprite requires minimal X-ray safety procedures, as all X-rays are contained within the leadshielded metal cabinet.

All X-ray activation is controlled by an interlock system. The X-rays will not turn on unless the top door is shut; likewise, the top door cannot be opened while the X-rays are on. Please remember that the X-rays are on during automatic or manual conditioning.

Protection

The use of external safety protection (e.g., lead aprons) is not necessary with Sprite; however, regulations concerning the wearing of radiation dosimeters by individuals exposed to radiation on a regular basis vary from state to state.

Liquids

Any liquid around Sprite represents a potential electrical shock hazard. You sh ould not spray, pour or otherwise allow any fluids in Sprite's vicinity. If you intend to scan liquids, they must be non-flammable and in a sealed container. For specific cleaning instructions, see Cleaning.

User Safety Symbols and Features

Sprite has a variety of safety symbols and features on the interface and outer cabinet and inside the lower cabinet, as shown here:

User Interface Safety Symbols

Symbol Name Description

Radiation Trefoil

Active X-ray Indicator Icon

Permanently affixed to each userinterface button that activates Xrays.

Permanently affixed to the user interface. This icon is yellow (or "illuminated") when the X-ray source is on.

Introduction and Basics

Safety Features

Feature Name Description

"X-ray On"

Indicator Lights

Operator "E-Stop" Button

Cabinet Safety Symbols

Symbol Name Description

Illuminating indicators located on either side of the touch screen that pulsate while X-rays are being generated.

Located on the front of the machine near the touch screen. This button should be pressed only in the event of an emergency.

WARNING

Risk of Danger Refer to Manual

WARNING

Risk of Shock

Located adjacent to the accessory power outlets.

Located adjacent to the accessory

CAUTION

X-ray Hazard

power outlets.

Located adjacent to each port that accesses the X-ray source.

WARNING

Hazardous Voltage

Located wherever a potential electrical hazard exists.

CAUTION

X-ray Hazard (Canada)

Located adjacent to each port that accesses the X-ray source.

Sprite User's Manual

Inner Cabinet Information

Information Item Description

Power Status Label

Located on the front of Sprite’s electronics enclosure near the power and key switches. This label supplies information about the power status of the computer and X-ray systems.

Identification Plaque

Located on the front of Sprite’s electronics enclosure near the power switch. This label supplies important information about Sprite and its certifications.

Introduction and Basics

Cleaning Sprite

Sprite is a state-of-the art cabinet X-ray system with a touch screen on the exterior and all electrical, mechanical, and computer components located inside. Because Sprite contains such components, its care should be similar to that of an appliance. Any liquid around Sprite should be considered a potential electrical shock hazard. You should not spray, pour or otherwise allow any fluids in Sprite's vicinity.

Brushed Stainless Steel

Sprite's front and staging area surfaces are primarily brushed stainless steel. IMTEC recommends the use of cleaning wipes formulated specifically for stainless steel.

Exterior Cabinet

Sprite's other exterior cabinet surfaces are metal and thick plastic. IMTEC recommends the use of multi-purpose pre-moistened cleaning wipes for these surfaces.

Touch screen

Sprite's touch screen is made of glass. IMTEC recommends the use of pre-moistened glasscleaning wipes for this surface.

External Machine Diagram

Sprite User's Manual

Machine Specifications

Sprite is a small industrial X-ray CT (computed tomography) scanning machine. Samples to be scanned are placed in a plastic or Styrofoam canister, which then is set on the stage in the cabinet.

Image viewing and reconstruction are performed through the embedded computer. Sprite allows you to transfer your scan data to a removable storage unit so you may download it to a computer that is equipped with ILUMAVision Industrial.

Sprite complies with all federal regulations for cabinet X-ray equipment set by the U.S. Food and Drug Administration, all UL standards for electrical equipment for measurement, control and laboratory use, and the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. This Class A digital apparatus complies with Canadian ICES-003. Please see Safety for more information.

Cabinet Specifications

Cabinet Lead-shielded metal cabinet. Shielded up to 150keV.

The front panel with the touch screen is a hinged door that opens upward for sample placement. The two doors on the lower front cabinet open to four compartments used to house all system electronics, store sample canisters and calibration phantoms and provide additional storage space for the user's needs.

Size Weight

User Interface

Indicators "X-ray On" illuminating indicators on either side of the touch screen that pulsate

Key Switch The insertion and rotation of the key is required for X-rays to be enabled.

Emergency Stop Button

Computer Embedded Computer with GPU reconstruction capabilities.

59" wide, 24" deep, 57" tall (with door closed) 800lbs

21" wide screen flat panel touch screen monitor. All system operations are performed through this interface and an on-screen keyboard allows the user to input text.

while X-rays are being generated. An additional connection provides a relay closure for an optional external sign. This connection is rated up to 240VAC 50/60Hz and 3A.

Located on the front of the electronics box. Pushing this button physically disconnects the power to both the X-ray source and

the motion stages. Located on the front of the top door.

X-ray System Specifications

X-ray Source

Filtration 0.010 inches Copper or 0.35 inches Copper Detector Varian 2520 (25cm x 20cm)

Kevex PXS10-65W Microfocus 130keV Maximum X-ray source potential – 130keV Maximum operating duty cycle – 100% Expected lifetime 10,000 hours typical

Fitted with DRZ High scintillator

Electrical System Specifications

Introduction and Basics

Power Consumption

External Connections

Rotary Stage Design

110-240VAC 50/60Hz 1400 Watts consumption max

1 x IEC power socket input (see Electrical Power Consumption for ratings) 2 x Ethernet – one for network, one for optional additional workstation 1 x External "X-ray On" sign contactor (relay closure), 240VAC @ 3A 3 x USB 2.0 – one on front panel, two inside shelf 2 x IEC power socket ouputs, same voltage as system input, 3A Maximum (both sockets combined)

Four separate, motion stages in fixed positions within the cabinet that allow for

four levels of magnification Motors Four 800 line/rev NEMA-23 hybrid stepper motor (one per stage) Circuit

Boards

1. System Board – Communicates to imbedded computer via USB and contains

the RFID.

Microchip dsPIC33FJ256MC710 microprocessor controls rotary stage motor, "X-

ray On" sign, and interlock switches. Located in the electronics cabinet beneath

the stage.

2. Canister Boards (4) – Controls the rotary motion of each stage and contains

an RFID antenna and an Allegro A3984 step motor driver chip. Located each

stage.

3. RFID Board – Implements RFID system and contains a reader card and

adapter card.

4. Filter Wheel Board – Selects from several different filter types automatically.

Located next to the X-ray aperature and has a step motor driver IC and optical

home position sensor.

5. Multiplexor card added for multiple motion stages.

Operating Specifications

Operating Environment

Maintenance Software enforced

Ambient Temperature – 10° to 30° Ambient Humidity – up to 80% RH Altitude – up to 7000 ft ASL

Contact Information

Sprite is a product of IMTEC, a 3M Company. If you have any questions about Sprite and its capabilities or if you have encountered a problem,

please contact us for assistance. Email: support@imtecimaging.com

Toll-Free Phone:

800-879-9799 Note: Our toll-free telephone numbers do not work from

outside of the United States Phone: 505-661-3000 Fax: 505-662-5179 International

001-505-661-3000 Phone:

Address: IMTEC, a 3M Company 110 Eastgate Drive Los Alamos, NM 87544

Sprite User's Manual

Basic Operation

This section provides an overview of basic operation, or quick-start, of Sprite. Please read the user’s manual for complete instructions and safety information.

Powering Sprite On and Off

To power Sprite on and off, you must insert the key into the key switch and turn it to the "on" position. You may power Sprite on and off with the power switch located on the front of the electronics enclosure, inside the lower cabinet. The system power switch activates and deactivates the entire mechanical and software system.

Activating Sleep Mode

To conserve energy without turning off the machine, you may activate the sleep mode (in the Utilities component). The touch screen will go dark with the exception of one remaining icon. To "wake" Sprite, tap the screen.

Using the Touch screen Interface

Sprite is equipped with a touch screen for ease of use. Use your finger(s) to tap the screen’s icons, enter settings and activate buttons.

Required Pre-Scan Procedures

Conditioning maintains the X-ray tube and prepares it for scanning. You may not begin a scan unless the tube is conditioned; you will be notified of such. To begin conditioning, tap the X-ray System Maintenance button on the main screen, and then tap the Begin Conditioning button.

Detector calibration prepares the detector for scanning and is esse ntial for accurate image acquisition. IMTEC recommends you calibrate the detector between once a da y and once a week. To begin detector calibration, tap the X-ray System Maintenance button on the main screen, and then tap the Begin Calibration button.

Sprite offers

CAUTION: Any liquid around Sprite should be considered a potential electrical shock hazard. You should not spray, pour or otherwise allow any open fluids in Sprite's vicinity. If you plan on scanning liquids, they must be nonflammable and in a sealed container.

automatic X-ray conditioning and detector calibration.

Introduction and Basics

Sample Placement

This topic covers the placement of items in the cabinet. Proper positioning is simple, yet it is essential to accurate imaging.

Your Sprite system includes canisters and accessories to help ensure the proper placement of your sample between the X-ray source and the detector. Items that may be used for sample placement include plastic canisters with specific scanning regions marked, Styrofoam canisters with shelves or cut-outs for specific samples, open platforms, and a variety of soft foams. These items are called fixtures. Each of Sprite's fixtures and calibration phantoms is tagged with an RFID card or sticker.

Canisters and Platforms

Each stage is color coded and has a specific canister and/or platform for its size.

Each canister has Styrofoam inserts to insure the correct placement of the sample within parameters marked on the canister. These parameters guarantee that your sample will be within the X-ray scanning field.

Platforms have Styrofoam disks to help adjust height of the item. Other soft foams may also be used for proper sample placement within the canister or platform.

Calibration Phantoms

Calibration phantoms can be placed directly on the stage. Sprite comes with color-coded aluminum cylinders, or "calibration phantoms", for each stage . To

test and calibrate the overall imaging system in Sprite, each stage should be regularly (we recommend monthly) calibrated. This calibration is referred to as a "System Calibration". You may run a "Validation" to confirm that the system is calibrated correctly.

Sprite User's Manual

Fixture/Phantom Placement

To begin a full imaging scan, place and secure your sample in the appropriate canister and on the appropriate stage. To begin a system calibration or validation, place and secure a calibration phantom on its corresponding stage. (A fixture/phantom is secured when it has been gently turned until it locks into place. An Audible Announcement informs you the fixture/phantom is secure.) Shut the cabinet door, tap Begin a New Scan, and choose the proper scanning options.

Notes

• If you cannot open the cabinet door, Sprite's interlock system is probably engaged. The door will unlock when the X-rays are turned off. For more information, see Safety.

• If you need replacement canisters, stages or foam accessories, please contact technical support.

• Do not insert flammable or explosive materials inside the Sprite cabinet.

• If you intend to scan liquids, they must be non-flammable and in a sealed container.

Contact Information

Sprite is a product of IMTEC, a 3M Company. If you have any questions about Sprite and its capabilities or if you have encountered a problem,

please contact us for assistance. Email: support@imtecimaging.com Toll-Free

Phone:

Phone: 505-661-3000 Fax: 505-662-5179 International

Phone:

800-879-9799 Note: Our toll-free telephone

numbers do not work from outside of the United States

001-505-661-3000

Address: IMTEC, a 3M Company 110 Eastgate Drive Los Alamos, NM 87544

Components

Main Screen

Sprite's main screen provides access to Sprite's main components. This is a reproduction of main screen. The components of this screen are described bel ow.

Begin a New Scan Button

Tap this button to open the Begin a New Scan screen.

This button provides access to all three types of scans – full imaging scans, system calibration scans, and validation scans. For more information on these, see Full Imaging Scanning, System

Calibration, and Validation.

Notes

• The type of scan is automatically determined by what is placed on the stage inside the cabinet.

• Full imaging scans are the primary function of Sprite. System calibration and vali dation are maintenance related.

Sprite User's Manual

One Touch Scan Button

This component allows you to conduct a scan quickly by using pre-set default scan settings. With One Touch Scan, you can skip the Begin a New Scan screen and start scannin g immediately. This component is ideal for scanning numerous items that require the same scan settings.

If you feel confident that you do not need a preview image and have placed your sample and entered default settings, tap the One Touch Scan button. The scanning process begins and you are taken directly to the Scanning page.

Note: To create or modify the default scan settings, tap the One Touch Scan Setup button on the Utilities screen.

Utilities Button

Tap this button to access various system functions, settings, and repair services or to create, save, and transfer trouble tickets.

When you tap this button, the Utilities screen appears.

Locate a Scan Button

Tap this button to access Sprite's Locate a Scan screen.

On the Locate a Scan screen you can search for scans, perform reconstructions, and manage scan files.

Components

Background Processing Button

The Background Processing button provides access to the Background Processing screen. This button appears on the main screen and in the bottom right corner of every screen.

If the gears of this button are moving, image processing (or reconstruction) is under way.

Note: You may not begin a scan while any image processing is under way.

X-ray System Maintenance Button

Tap this button to access the maintenance procedures to regularly perform on Sprite. These procedures – conditioning and detector calibration – are req uired for the X-ray source and

detector to perform at their highest levels.

When you tap this button the X-ray System Maintenance screen appears.

Begin X-ray Conditioning

If the X-rays have not been conditioned within the required time frame, a message reading "Begin X-ray Conditioning" will appear below the X-ray System Maintenance button. (In addition, a message readying "X-rays Need Conditioning" appears below the Begin a New Scan and One Touch Scan buttons.) If you receive this message, you must condition the X-rays before scanning.

Tap the X-ray System Maintenance button to begin X-ray conditioning. The conditioning begins automatically, and the X-ray System Maintenance screen appears.

Sprite User's Manual

To find out about scheduling automatic conditioning and detector calibration, please see

Scheduled Maintenance in the X-ray System Maintenance component.

Messages

Messages appear in yellow text on the main screen under the main components. They indicate the status of the system and what actions, if any, you must take before starting a scan.

Please refer to the following table for specific messages

Message Button Indicates

X-rays Need Conditioning

Nothing To Scan

Not Ready To Scan

Too Many Items

Scan In Progress

No Available Drives

Reconstructing Begin a New Scan,

Begin X-ray Conditioning

Notes

• The trefoil indicates which buttons activate X-rays.

Begin a New Scan, One Touch Scan

One Touch Scan X-ray System

Maintenance

Must begin the conditioning procedure by tapping the X-ray System Maintenance button

Must place an item in the cabinet and be sure that the RFID tag has been read

The system is not ready to begin a scan

There is more than one item placed in the cabinet

A scan is in progress and that a new scan cannot begin until it finishes

The data drive(s) have not been assigned or may be full

There is a current reconstruction running and that a scan cannot begin until it finishes

Must tap this button and condition the X-rays before starting a scan

• Sprite also features audible announcements.

Components

Begin a New Scan Screen

The Begin a New Scan screen appears when you tap Begin a New Scan on the main screen. Use this screen to choose the settings (or parameters) for a full imaging scan, a system calibration or validation.

Note: The screen capture below applies to a full imaging scan. The screen is configured slightly differently for system calibrations and validations. Sprite determines by what you place on the stage whether you are performing a full imaging scan, a system calibration or a validation.

To start the actual scan, fill out the scan settings (Scan Name, Resolution, etc.), and then tap the Scan button. The scanning begins, and you are taken to the Scanning screen.

This is a reproduction of the Begin a New Scan screen. The components of this screen are described below.

Image Area

Any preview images produced prior to scanning are displayed on the screen. You may want to adjust the sample's placement or the scan settings after seeing the preliminary image.

Sprite User's Manual

Scan Settings

The scan settings differ depending upon whether you are performing a full imaging scan, a system calibration or a validation.

When you perform a full imaging scan, the scan settings section looks like this:

Scan Length

The scan time and processing time vary with the scan settings you choose. Take note of these times, especially after you make changes to the settings, because you may not want to start a scan that will take more time than you have.

Scan Energy

The Scan Energy (or strength of the X-ray) setting determines how well it can penetrate the object and affects the contrast of the image.

Resolution

The Resolution setting determines the quality of your image. High-resolution scans produce more data (or lines per millimeter), though they also take more time to process.

Scan Quality

The Scan Quality setting determines how thorough your scan will be and how much detail is produced. CT scanning is based on hundreds to thousands of acquired images that are averaged together to create the most accurate result.

When you set the quality to a higher level, the item is scanned more intensely, more detail is produced, and the scan time increases.

Sprite offers five quality settings – Quick Scan, Medium, High, Very High, and Extreme Quality. To change the quality setting, tap the slider.

Components

When you perform a system calibration or a validation, the scan settings section looks like this:

Scan Name

The scan name can be entered (by tapping in the box and entering information with the keyboard) or will be automatically assigned when you choose a system calibration or validation. The abbreviation "Cal" or "Val" will appear in the name box and on the following screen in the title bar with a time stamp.

Scan Type

Select Validation or Calibration.

Scan Length

Resolution

The Resolution setting determines the quality of your image. High-resolution scans produce more data (or lines per millimeter), though they also take more time to process.

Note: Resolution appears only with validations (and not with calibrations).

Sprite User's Manual

System Calibration or Validation Settings

When you perform a system calibration or a validation, the scan settings section looks like this:

Scan Name

Scan Type

Select Validation or Calibration.

Scan Length

Resolution

The Resolution setting determines the quality of your image. High-resolution scans produce more data (or lines per millimeter), though they also take more time to process.

Note: Resolution appears only with validations (and not with calibrations).

Preview Image Button

Tap this button to get a preview (or scout) image of the sample and display it on your screen. Based on this image, you may want to adjust the sample's placement or scan settings. This feature can help ensure the quality of your full scan.

Note: When you tap Preview Image, the X-ray source is activated, icons change accordingly and the Turn X-rays Off button appears.

Components

Save Button

If you would like to save your preview (or scout) image, tap the save button and a copy of it will be saved on the active data drive.

You may find all saved scans through the Locate a Scan component.

Stage Position Control

You may turn the stage from outside of the cabinet using the Stage Position Control on the screen. You may want use this control in combination with the

preview image feature to ensure accurate sample placement.

The Stage Position Control contains an inner dial and an outer dial. The outer dial indicates the current position of the stage. If you would like to change the position of the stage, drag the inner dial either way. The outer dial (and stage) will turn to line up with the inner dial when your finger is released from the screen.

The outer dial (and stage) will turn to line up with the inner dial when your finger is released from the screen.

Scan Button

After entering the scan settings and, if necessary, reviewing the preview (or scout) image, tap the Scan button to start the full imaging scan, system calibration or validation.

Note: You cannot start a full imaging scan, system calibration or validation unless the Scan button is activated (that is, unless the text on the button is white). If the scan button is not activated, make sure your scan name and settings are completely and accurately indicated.

When the Scan button is tapped, the X-rays turn on, the scan begins, and the Begin a New Scan screen appears.

Scout Penetration

The scout penetration shows the minimum and maximum amount of X-rays that are able to penetrate the object during the preview (or scout) image. These amounts vary with the density of the object being scanned.

Sprite User's Manual

Full Imaging Scanning, System Calibration, and Validation

The type of scan – whether full imaging scan, a system calibration or a validation – is determined by what you place on the stage.

Full Imaging Scanning

Full imaging scans are the most common activity you will perform with Sprite. Although validation and calibration likely will be performed regularly, they likely will not be performed as frequently as full imaging scans.

Your Sprite system includes fixtures (canisters and/or Styrofoam) and accessories to help ensure the proper placement of your sample between the X-ray source and the detector. For more about putting a samples in the cabinet see Sample Placement.

To begin a full imaging scan, place the fixture on the stage and an Audible Announcement will sound. Shut the cabinet door, tap Begin a New Scan and choose the appropriate scan settings on the Begin a New Scan screen.

System Calibration

System calibration is a procedure that calibrates the overall imaging system. System calibration should be done regularly, preferably once a month. It must be done after the machine is installed, moved, or physically disturbed.

Sprite comes with a color-coded aluminum cylinder, or "calibration phantom". To begin system calibration, place the calibration phantom on the stage and an Audible

Announcement will sound. Shut the cabinet door, tap Begin a New Scan, and choose the Calibration option in the drop-down box on the Begin a New Scan screen.

Validation

Validation is a procedure you can occasionally run to confirm that the entire system is scanning, acquiring data, and producing images and reconstructions correctly. The validation procedure is similar to System Calibration and ensures the system calibration is correct.

Sprite comes with a color-coded aluminum cylinder, or "calibration phantom" that is used for system calibration and validation.

To begin validation, place the calibration phantom on the stage. An Audible Announcement will sound. Shut the cabinet door, tap Begin a New Scan, and choose the Validation option in the drop-down box on the Begin a New Scan screen.

Components

Scanning Screen

This screen displays the progress of your scan and provides for the entry of key scan information. This is a reproduction of the Scanning screen. The components of this screen are descri bed

below.

Scan Progress

Before scanning begins, the system must prepare itself. As it does so, it displays in the scan progress area the steps it is taking. (These steps are determined by the scan settings.)

After scanning begins, the scan progress area displays the progress of the scan, including the amount of time remaining until the scan is complete.

Upon completion, the scan is automatically saved, and the Scan Review screen appears.

Sprite User's Manual

Image Area

The image area contains images produced in real time by the scanning process.

Components

Scan Review Screen

This screen allows you to view the status of the various scan types (i.e., reconstruction, system calibration, or validation), to access the results of the scan, and to manipulate the scan's raw images. When the scan is complete, you may tap the associated arrow in the table to see the full results.

After your sample is scanned, the raw image is automatically processed to allow for further reconstruction. This screen allows you to view the status of the various scan types (i.e., reconstruction, system calibration, or validation) as they process. You may also manipulate the scan's raw images and access the Processing Setup screen to process a reconstruction or view completed reconstructions.

You will know automatic processing is finished when three images appear in the table (these are the top, front, and side views of your sample). To begin a reconstruction job, tap the Process button. After entering the settings on the following screen, you will return to this screen while the processing takes place. When the processing of the system calibra tion or validation report processes or the reconstruction job is complete, you may tap the associated arrow in the table to see the full results.

Note: You may perform unlimited reconstructions on any full imaging scan. All reconstructions of a single image will appear on this screen in the scan/reconstruction table and may be accessed through the Locate a Scan screen.

This is a reproduction of the Scan Review screen. The components of this screen are described below.

Sprite User's Manual

Image Area

The image area contains the raw images produced by the scan. This is an image of an aluminum part.

This is an image of the calibration phantom.

Note: These images can be examined and manipulated while reconstruction occurs.

Action Button

The Action button represents actions that can be performed on the data. The button represents verification for the user that the data can be processed into the next state.

Most likely this button will read "Process", which means that the system is ready to perform a reconstruction. When you tap the Process button, you will be taken to the Processing Setup screen to enter the reconstruction request.

Table Settings Button

The Table Settings button opens a dialog box that allows you to choose which columns are displayed in the table on the Scan Review screen.

Select the check box next to the column headings you would like to see, and then tap Close to enable your changes.

Components

The column headings include:

GUID - Global Unique Identifier Operation - messages generated by the FlashCT-

DPS software regarding the reconstruction Description - description of the scan entered by the

user Comment - system-generated text that displays

what reconstruction action is taking place

Scan/Reconstruction Table

This table contains and provides access to the scan and all of the reconstruction information, as well as system calibration and validation reports.

This is a reproduction of the Scan/Reconstruction table. The components of this image are described below.

Note: When reconstruction is under way, the gears in the Background Processi ng icon in the lower right corner of the screen are in motion.

Delete

Tap the Delete button to delete the scan data. You will be asked to confirm your intention.

A dialog box indicates when the deletion is complete.

Sprite User's Manual

Copy

Tap the Copy button to copy the scan data to a different active drive (such as a USB flash drive).

When you tap the button, the list of active drives appears.

Select the drive to which you want the copy sent. You will be asked to confirm your intention. A dialog box indicates the status of the copy.

Move

Tap the Move button to move the scan data to a different active drive (such as a USB flash drive).

When you tap the Move button, the list of active drives appears.

Select the drive to which you want the file sent. You will be asked to confirm your intention. A dialog box indicates when the move is complete.

For more information about adding data drives, please see Storage Device Management in the Utilities component.

Processing Status

If you are performing a full imaging scan, reconstruction, system calibration or validation (and therefore, by extension, are performing a reconstruction), the Processing Status area displays the progress of your reconstruction.

When the automatic processing of a full imaging scan and any reconstructions are complete, the Processing Status area displays images (top, front, and side views) of the processed data before a reconstruction, the top view of a volume reconstruction or a polygon (indicating a surface reconstruction).

Components

When the system calibration or validation is complete, the Preview Image area is colored white to indicate a successful validation and red to indicate an unsuccessful one. Tap the Report button in the upper right corner to generate the full report.

Note: When reconstruction is under way, the gears in the Background Processi ng icon in the lower right corner of the screen are in motion.

GUID

The GUID (Global Unique Identifier) column displays a system generated identification number assigned to each scan and subsequent reconstructions.

Operation

The Operation column displays messages generated by the FlashCT-DPS software regarding the reconstruction process.

Note: Text only appears in this column during active reconstruction and processing.

Description

The Description column displays the original scan's description entered by the user on the Scanning screen.

Comment

The Comment column displays system-generated text that displays what reconstruction action is taking place.

Note: Text only appears in this column during active reconstruction and processing.

View Surface or Volume Reconstructions or Calibration/Validation Results

Tapping the arrow on any row in the table takes you to the Results screen.

If you open the Results screen from a full imaging scan, it will contain the surface and/or volume reconstruction.

If you open the Results screen from a system calibration or validation, it will contain a report on the respective validation or calibration.

Note: You cannot access the surface model of a reconstruction or the results of a validation while the reconstruction is under way (i.e., while the gears in the Background Processing icon in the lower right corner of the screen are in motion)

Sprite User's Manual

Processing Setup Screen

The Processing Setup screen allows you to choose settings for in-depth reconstructions. Among these settings is Region of Interest. With this setting you may designate a subvolume to

reconstruct. To start the processing, fill out the reconstruction processing settings (set the region of interest,

update the description, select the data type and resolution, etc.), and then tap the Start Processing button. The image processing begins, and you are taken to the Scan Review screen.

Note: You may not begin a scan while a reconstruction is processing.

This is a reproduction of the Processing Setup screen. The components of this screen are described below.

Region of Interest

This screen displays three views (top, front, and side) of an image produced on the Scan Review screen. From these images, you must choose a region of interest (or ROI) to perform intensive reconstruction on.

Components

Automatic ROI

A region of interest will automatically appear as a red box over a portion of the image.

Adjusting the ROI

If you would like to adjust the ROI, tap the image with the ROI you would like to adjust and the surrounding box will be highlighted in yellow. Put your finger near the area you would like to reconstruct, and drag it over the area you would like to see. A square appears over the area. This is the ROI, and it applies to all three images. If you would like to manually adjust the ROI you may use the manual ROI adjustment buttons.

If you want to make the ROI boxes bigger, tap the expand button.

Tap an arrow in the direction that you would like to expand the ROI. For example, if you would like to expand the right side of the box, tap the arrow that points to the right and the side of the box will expand.

Sprite User's Manual

ROI before expanding Right expand arrow ROI after expanding

If you want to make the ROI boxes smaller, tap the collapse button.

Tap an arrow in the direction that you would like to collapse the ROI. For example, if you would like to collapse the height of the box, tap the arrow that points down and the top of the box will move down.

ROI before collapsing Collapse down arrow ROI after collapsing

Estimated Processing Time

The estimated processing time is computed from data chara cteristics and from your settings.

Processed Data Type

Processed Data Type indicates the types of reconstruction jobs Sprite will produce.

• Volume – produces an internal view from the slices

• Surface – produces an external three-dimensional model of the object

Select the type of reconstruction you want to produce.

Components

Resolution

The resolution setting is used to resolve (similar to zooming in) a small detail of a whole item. The higher the resolution setting, the better the quality of imaging (therefore, a longer processing time).

Processing Button

After choosing the settings for the image reconstruction, tap the Start Processing button to begin the reconstruction processing.

When processing begins, the screen returns to the Results screen, and the reconstruction process information appears in the scan/reconstruction table.

Sprite User's Manual

Results Screen

The Results screen differs depending upon whether y ou are performing a full imaging scan, a system calibration or a validation.

This topic describes the Results screen as it pertains to full imaging scans. For a description of the Results screen as it pertains to system calibrations and validations, see below.

In the context of full imaging scans, the Results screen allows you to explore the threedimensional surface or volume slice images produced by the reconstruction.

This is a reproduction of the Results screen. The components of this screen are described b elow.

Note: If you would like to conduct image analysis and manipulation beyond what we offer on Sprite, you may install IMTEC's ILUMAVision Industrial software on another workstation. ILUMAVision is personal computer–based imaging software that provides two- and threedimensional visualization and analysis, as well as various multi-planar reconstruction (MPR) functions.

Image Area

The image area contains the image associated with the active image selection button.

3-D Surface (or PLY) Reconstruction Viewing Techniques

You can look at these surfaces from any direction. To change the viewing direction, put your finger on the screen and drag it in any direction. You will notice that the image rotates in the direction of your drag.

To make the image spin, take your finger off the screen while you are dragging it. To speed up or slow down the spin, repeat the previous step with a faster or slower finger movement.

Tap an image to stop it from spinning. Tap an image twice to reset it to its default state.

Volume (or STL) Reconstruction Viewing Techniques

Follow the same techniques for viewing and manipulating preview and raw images.

Components

Surface Export

All scans and data derived from them – including reconstructions, surface (or "PLY) files and volume (or "STL") files – are automatically saved in the active data drive. To copy a scan's surface file to another drive, tap the drive's name in the Export surface to drive list.

Sprite User's Manual

Results Screen – Calibrations and Validations

If you are performing a system calibration or validation, the Results screen provides a detailed report of your results.

This is a reproduction of the Results screen for a system calibration. The components of this screen are described below.

Report Button

The button on the Results screen shows the user what is displayed on the screen. If a system calibration or validation report has been generated and appears on the scree n, the button becomes red.

System Calibration and Validation Reports

System calibration and validation reports provide detailed information on your machine's spatial calibration and noise. This information is determined by the ASTM Standard Test Method for Measurement of Computed Tomography (CT) System Performance.

The system calibration and validation reports are essentially identical. Both provide information about how Sprite's imaging system is operating. The difference is that the validation report is based on more intensive testing.

If your report has a red background, the calibration or validation failed. (Failure also is indicated by a red box in the scan table.) If your system calibration or validation fails, please contact tech

support before beginning another scan.

Components

General Information

The general information lists the specifics of the calibration including the part, system, and date.

Cylinder Diameter

The cylinder diameter lists the actual diameter, the measured cylinder diameter, and the difference between the two.

Spatial Calibration

The spatial calibration analyzes the geometrical sharpness of the image. Geometrical blurriness limits the ability to image an object's fine structural detail.

Noise Level

Noise is expected and acceptable. Excessive noise limits the ability to detect the presence or absence of features in an object.

Point Spread Function (Full Width at Half Maximum)

The point spread function gives the measurement of the sharpness of an image.

Modulation Transfer Function (50% level)

The modulation transfer function illustrates the system's spatial frequency re sponse in the reconstruction volume.

Sprite User's Manual

Locate a Scan Screen

The Locate a Scan screen allows you to:

• search for scans by entering identifying information,

• access scan data for viewing and reconstruction,

• copy, move, and delete scans, and

• access the system calibration and validation history.

All scans are saved to an active data drive and may be accessed through this component. This is a reproduction of the Locate a Scan screen. The components of this screen are described

below.

Scan Table

This table contains scan information and allows you to access a scan (and all reconstructions associated) and system calibration or val i dation data.

This is a reproduction of the Scan table. The components of this image are described below.

Page Up and Page Down Buttons

To look page by page in the information table for a scan, tap the Page Up and Page Down buttons.

Components

Scrolling is also available by tapping on the up or down arrow or dragging the bar in the column on the left side of the table.

Search Button

You may conduct an advanced search for scans (with or without reconstructions), system calibrations or validations by entering details of a scan you would like to find. Access the search window by tapping the Search button.

You may search by the name of the scan, the name or identification number of the person who performed the scan, and/or the date the scan was performed. If you want to search only the items in the system calibration and validation history, select the check box at the bottom. Tap Begin Search to run the search.

Sprite User's Manual

Search results are displayed in the table.

Table Settings Button

The Table Settings button opens a dialog box that allows you to choose which columns are displayed in the table on the Locate a Scan screen.

Select the check box next to the column headings you would like to see, and then tap Close to enable your changes.

Column heading descriptions are as follows: Name - the scan's name, as entered by the user (or

as generated by the system during one touch scans) Description - the scan's description, as entered by

the user Comment - system-generated text that displays what

reconstruction action is taking place Operator Name - the employee's name or number,

as entered by the user Scan Location - the name of the data drive on which

the scan is stored

Scan Type - the type and quality of scan Date Created - the date the scan was created

Components

Background Processing Screen

The Background Processing screen allows you to:

• view the status of active reconstruction jobs,

• view the list of pending reconstruction jobs, and

• abort active and pending reconstruction jobs.

The Background Processing component can be accessed by tapping the Reconstruction button on any screen.

Note: You may not begin a scan while a reconstruction is processing.

This is a reproduction of the Background Processing screen. The components of this screen are described below.

Reconstruction Table

The reconstruction table displays information on active and pending reconstruction job s. This information includes the job. (Each reconstruction job occupies its own row in the table.)

You may abort any reconstruction job at any time by tapping the Abort Job button.

Sprite User's Manual

Utilities Screen

The Utilities screen gives you access to various system functions, settings, and system servic es. Functions you may run regularly include System Sleep, System Shutdown, and Touch screen

Calibration. Settings you may enter or update include Storage Device Management, Network Configuration,

and One Touch Scan Setup. System services you may occasionally use (after speaking with technical support) include Submit

Trouble Ticket, Reset Processing Engine, Reset System Board Service, Reset X-ray Service, Reset Scan Engine, and System Restart.

This is a reproduction of the Utilities page. The components of this screen are described below.

System Sleep Button

When Sprite is not in use, you may deactivate the system. Deactivating the system, or putting it into System Sleep, allows you to lower power consumption without powering off the machine.

To deactivate the system, tap the System Sleep button.

When you tap this button, the screen goes dark. The system remains deactivated until the touch screen is touched, at which time the Utilities screen reappears.

Touch screen Calibration Button

Touch screen calibration ensures the touch screen is responding properly when it is tapped.

Components

If the touch screen is not responding as you would expect it to, tap the Touch screen Calibration button. Calibration will begin automatically.

Follow the instructions on the touch screen to calibrate it. First, touch the target as it moves around the screen.

Next, tap the screen and drag your finger. If the cursor follows your finger, tap the green check box. If the cursor does not follow your finger, tap the retry button, and the calibration will run again.

System Shutdown Button

To power off the entire Sprite system, tap the System Shutdown button.

Confirm or stop the shutdown in the confirmation window.

Note: If you shut down the system all the programs that are running will stop, and you may lose data. Further, any scheduled automatic detector calibration and conditioning will be canceled.

Sprite User's Manual

Storage Device Management Button

Sprite uses only external hard drives for performing and storing scans. Your Sprite comes equipped with one external hard drive (USB 1TB external HDD). There is one USB port and auxiliary power outlet located inside the bottom cabinet. The USB port on the front of the cabinet near the top door gives you the option of transferring scan data to another drive (a USB flash drive, for instance) for use on another workstation.

To determine or change the location, or data drive, of the stored data in Sprite, you may tap the Storage Device Management button.

When you tap this button, the Storage Device Management screen appears.

Storage Device Management Screen

The Storage Device Management screen allows you to add data drives to your Sprite system and determine which drive is used for data storage. You can name and rename your drives on this screen, as well.

Sprite uses only external hard drives for performing and storing scans. You will be provided with one external hard drive (USB 1TB external HDD) upon your purchase of Sprite. The USB port on the front of the cabinet gives you the option of transferring scan data to another drive (a USB flash drive, for instance) for use on another workstation.

Before you can store data on a drive, you must determine whether the drive can be used for data storage. To do so, first plug the drive into a USB port. If you do not see the name of the drive appear in the list of detected storage devices tap the Search For Drives button, and your drive will appear in the list.

When you tap the drive name, Sprite runs a performance test to determine whether the drive can be used for data storage. If the drive passes the test, it is automatically placed in the list of data drives.

The Storage Device Management screen contains two lists:

• Detected Storage Devices – drives detected that have not been tested and approved

• Active Data Drives – drives tested and approved for scan data storage

Components

This is a reproduction of the Storage Device Management screen. The components of this screen are described below.

Active Data Drives

Active data drives are those assigned to store scan data. (For information on the assignment of drives, see Detected Storage Devices.)

You may name each assigned data drive. To do so, tap the drive icon. The Drive Name box appears.

Tap inside the box, and enter the name for the data drive.

Tap the drive icon again. The new name appears.

Sprite User's Manual

Search for Drives Button

Detected Storage Devices

The default Sprite data drive is an external drive located in the cabinet, plugged into the internal USB port. Devices listed under Detected Storage Devices have been detected in a USB port but not yet tested and approved for data storage. To test and approve a drive, tap on the drive's name and you will be asked to confirm your actions.

Sprite will run a performance test on the drive. If the drive is capable of storing scan information it will appear in the Active Data Drives.

Network Configuration Button

To access the network configuration settings, tap the Network Configuration button.

When you tap the Network Configuration button, the Network Configuration screen appears.

Network Configuration Screen

This screen displays and allows you to enter or change the information about your local area network (if applicable).

This is a reproduction of the Network Configuration screen. The components of this screen are described below.

Components

Network Configuration Parameters

Sprite is capable of networking with other computers and connecting with the internet. To take advantage of this capability, you must have an available Ethernet outlet and an established local area network (LAN). The Sprite installer will configure your system for networking and internet connectivity. If Sprite is networked to the internet, you will be issued a web site to view the scans and their accompanying files online (from another workstation).

If an outlet or network becomes available after installation, you may configure your system using the following form:

If you are manually entering the information, tap on each line and enter the numbers with the key

pad in the appropriate rows.

Sprite User's Manual

Revert Button

To clear information entered and revert to the previous settings, tap the Revert button.

One Touch Scan Setup Button

To create default scan settings, which allow you to take advantage of One Touch Scan, tap the One Touch Scan Setup button.

When you tap this button, the One Touch Scan Setup screen appears.

One Touch Scan Setup Screen

Use this screen to set or modify the default parameters used in One Touch Scan. This is a reproduction of the One Touch Scan Setup screen. The components of this screen ar e

described below.

Scan Parameters

Tap the tab of the appropriate stage (which correlates to level of scan).

Components

Enter the other default settings to conduct full scanning and viewing procedures. The scan energy determines the strength of the X-rays. The resolution setting determines the quality of your scans. High-resolution scans produce more data (or lines per millimeter) but require a longer processing time.

Note: You must set the default scan settings for each stage for wish you wish to perform One Touch Scans.

Save Button

If you would like to save your preview (or scout) image, tap the save button and a copy of it will be saved on the active data drive.

Note: You may find all saved scans through the Locate a Scan component.

Restore Button

Tap the Restore button to reset the settings to their original state.

Submit Trouble Ticket Button

Trouble tickets help IMTEC technical support staff to diagnose and correct any problems you may encounter when using Sprite. These tickets contain not only your description of the problem, but also additional internally generated system/process information.

To create a trouble ticket, tap the Submit Trouble Ticket button.

Sprite User's Manual

When you tap the Submit Trouble Ticket button, the Submit Trouble Ticket screen appears.

Submit Trouble Ticket Screen

Trouble tickets help IMTEC technical support diagnose and correct any problems you may encounter when using Sprite. These tickets contain not only your description of a problem, but also additional internally generated system/process information.

This screen allows you to create and submit a trouble ticket. By default, trouble tickets are stored on the active data drive, but you have other options, as well.

This is a reproduction of the Submit Trouble Ticket screen. The components of this screen are described below.

Description of Trouble

The trouble ticket box allows you to describe the trouble you are having. To enter information, first tap inside the box. When the keyboard becomes active, type in the trouble you are having or any question you have about the system. In your trouble ticket please state: what function you were running before the problem occurred, if it was reproducible or not and any steps that were taken to correct the problem.

Export Ticket

Components

To save the ticket to another drive (to transfer it to another workstation, for example), choose the drive from the list. (Be sure you have connected the drive to one of the available USB ports.)

Keep a Local Copy of Ticket

Tickets saved to the current active drive can be retrieved by a technician to assess any problems. To save the ticket to the active drive tap/select the box next to Keep a local copy.

Submit Button

Tap the Submit button to save and/or export the trouble ticket.

Reset Processing Engine Button