LED BAR
64pcs 1.5W RGB 3-in-1 LED
Ver1.0
1
Table of contents
1. Preface ················································································ 2
1.1 Packing list ····················································· 2
1.2 Unpacking instructions ································ 2
1.3 AC Power ······················································ 2
1.4 Safety instructions ·························································· 2
2. Introduction ·········································································· 3
2.1 Features ························································ 3
2.2 quick start ·················································· 4
3. Setup ····················································································· 5
3.1 Fixture linking ·············································· 4
Data connect ················································ 5
Cable wire’s adapter ··········································· 5
3.2 Setting up a DMX serial data link ···································· 5
3.3 Setup ················································································· 6
4. Operating instructions ························································· 6
4.1 Menu configure ··············································· 6
4.2Menu structure and comments ························ 6
4.3 User configurations ······································· 8
4.4 DMX channel values ······································ 8
5. Technical specifications ······················································· 9
2
1. Preface
1.1 Packing list
Product name quantity
LED Par Light 1 pc
Power -cable 1 base
User manual 1 pc
1.2 Unpacking instructions
When you get this product, please take it from carton carefully to make sure whether all the
accessories are in and damaged or not.When you find that there are any parts or wrong sign
with the carton, or non-operation, please inform us and to keep the carton and shipping bill
completely.
1.3 AC Power
Please check the manual book before you operate the light. The rating current of the light
listed which shows the average current-consume under the normal circumstances.
All the lights must be offered shoot-through circuit, it couldn’t be connected dimmer circuit,
although the dimmer channels are completely for 1-100% switch.
1.4 Safety instructions
Before the light’s working, please confirm the correct voltage.
Please confirm there is no flammable material around the light.
The light must be set up the ventilating place. The distance is ≥51cm around approach
material. To check the air passage is ok at any time.
The Maximum temperature is ≤40℃(104℉).
When the lights has problems, please stop to use to seek the professional counseling or
manufacturer.
Please turn off the power before maintenance, modification is prohibited.
Don’t look the bulb for a long time,so as not to affect vision when the light is working to
avoid any hurt.
2. Introduction
2.1 Features
*Voltage: AC100/240V, 50/60Hz
*Power consumption:117w
*Light source: 64*1.5W RGB 3 IN 1 LED
*Color mixing:RGB
*Beam angle:45 degree
*Strobe:0-16Hz, from slow to fast, adjusting
3
*Electronic dimmer from 0 to 100%
*Control mode: Auto, Sound ,DMX512
*DMX channels:2/3/4/7/14/26
*LED digital display
*Data out/in:3 pin XLR-connection sockets
*Size:1050*75*120mm
*Net weight:3.5kg
2.2 quick start
Ø Operating mode switch and Settings：
n The main menu, the display of each menu item, are "external control mode"
u Default is "DMX512 console control", only to receive standard DMX512 signal, 1
decimal point will shine. Otherwise please check whether it is right to connect to
the console
l If you want to modify the DMX address code, please press "MENU" button
until you see continuous "dxxx", press "UP" and "DOWN" to adjust address
code, press "ENTER" key to save
l If you want to select DMX channel mode, please continuous press "MENU"
button until you see the "SET", press "ENTER" button to ENTER submenu
"ChNd" to choose from 11 ch / 5 ch
l There are five kinds of adjustable speed of light (decided to move light soft
degrees) to choose from (" SET "menu" LinE "and console mode under 11
channels)
u If you want to use "master-slave machine control", please set a lamps and
lanterns to the model, and the other without any set of lamps and lanterns, will
automatically identify the host signal source, the lamps and lanterns show from
the machine will automatically jump "dxxx" menu, the decimal point 1 will shine
u Must ensure that the one and only one control source (a host or a control table) :
if there are multiple signal source in the same line, the signal will disturb each
other, result in unable to correctly receive data from the machine
n "Static model", please enter the RGBW menu (to be automatic into the host state)
n "The pattern" enter "CCxx/CPxx/DExx" menu (to be automatic into the host state)
n "Acoustic model", please enter the SoUd menu (to be automatic into the host state)
3. Setup
3.1 Fixture linking
When you control the light’s master/slave or DMX 512 signal agreement, the lights can be
connected by signal wire which the distance is ≤500m,The maximum connect lights are 32pcs
more or less, and adapt DMX light pair to segregate the signal zoom equipment, in order to
protect the light’s signal won’t be interrupted by other signal. Moreover, it won’t affect by the
signal wire’s length
Data connect
Data cable is connected by DMX data wire, and XLR. Please use hi-quality data cable signal wire,
4
it won’t be interrupted by magnetic.
Cable wire’s adapter:
The two sides of signal cable wire is consisted of 1 pair female and male 3 XLR plug, which is
correspond the lights or DMX controller,
3.2 Setting up a DMX signal connect
As following pictures show, please connect the first light to the signal cable which is with XLR
by DMX controller, then, connect light in series.
3.3 Setup
The light must be set up the ventilating place. To confirm there is nothing to hinder the heat
dissipation place. When the light is hanged, please choose a safety wire.
4. Operating instructions
4.1 Menu configure
There are 4 buttons located in the bottom of the LED digital display when you check the menu
configure of the bottom of light. Show as follow:
Note: Please choose ”ENTER” return to the main menu to save the address code or mode
after you set up. When the light is lighting, the display of the address code or mode is same
as the last time when you operated.
4.2 Menu structure and comments
Addr A001-A512 512 address setting
CHnd
3CH 3 channel setting
7CH 7 channel setting
24CH 24 channel setting
28CH 28 channel setting
SLnd
Auto master auto
Soun master sound model
SL 1 DMX
SL 2 Slave
SH** 0-15
master select of auto
（recommend channel 15）
SP** 0-100 Speed of auto
MENU UP DOWN ENTER
5
SN** 0-100 Sound sensitivity
r*** 0-255 red dimming
G*** 0-255 green dimming
b*** 0-255 blue dimming
LEd OFF
After 5 seconds the screen
is off
ON The screen is always open
4.3 User configurations
Set-up 1pcs light`s menu mode (Auto-running)
.Press the MENU, such as the picture 4.2 shows the menu function
.Use the UP/DOWN buttons to choose the right one to confirm.
To set Master-slave mode
.Press the MENU, same as picture 4.2 shows the menu function
Master: Set any one of lights to auto、sound or strobe control mode
Slave: Set them to DMX mode and their address code to1.
Notes：Each Master-slave group can be one and only light in master, ensure lights under this
group without connection with any DMX controller.
To set DMX mode
The light can connect to the DMX controller to receive its signal indication, which control by
DMX controller. DMX value is referenced by “4.4 DMX channel values”.
4.4 DMX channel values
DMX channels
2channels functions specification
1
no function
0-8
auto
9-127 （Recommend effect15（121-127））
sound
128-255（Recommend effect15（247-255））
2 speed/sensitivity 0-255
Button Function
<ENTER>
Each operation to be confirmed
<DOWN-<UP>
Down-Up
<MENU>
menu option
6
3channels
functions specification
1 red brightness adjust 0-255
2 green brightness adjust 0-255
3 blue brightness adjust 0-255
4channels functions specification
1
general brightness adjust
0-255
2
strobe
0-255
3
no function
0-8
auto
9-127 （Recommend effect15（121-127））
sound
128-255（Recommend effect15（247-255））
4 speed/sensitivity 0-255
7channels functions specification
1
general brightness adjust
0-255
2
strobe
0-255
3
no function
0-8
auto
9-127 （Recommend effect15（121-127））
sound
128-255（Recommend effect15（247-255））
4 speed/sensitivity 0-255
5 red brightness adjust 0-255
6 green brightness adjust 0-255
7 blue brightness adjust 0-255
14channels functions specification
1
general brightness adjust
0-255
2
strobe
0-255
3
the 1st/2nd group red bright
0-255
4
the 1st/2nd group green bright
0-255
5
the 1st/2nd group blue bright
0-255
4
the 3rd\4th group red bright
0-255
6
the 3rd\4th group green bright
0-255
7
7
the 3rd\4th group blue bright
0-255
……………………………………………
……………………………
12
the 7th\8th group red bright
0-255
13
the 7th\8th group green bright
0-255
14
the 7th\8th group blue bright
0-255
26chann
els
functions specification
1
general brightness adjust
0-255
2
strobe
0-255
3
the first group red bright
0-255
4
the first group green bright
0-255
5
the first group blue bright
0-255
6
the second group red bright
0-255
7
the second group green bright
0-255
8
the second group blue bright
0-255
……………………………………………
……………………………
24
the eighth group red bright
0-255
25
the eighth group green bright
0-255
26
the eighth group blue bright
0-255
5. Specification
Voltage AC100V -240V/50Hz/60Hz
Control mode Auto, master-slave,DMX512 signal
Max temperature 104°F(40°C)
Data input/output 3pin XLR-connection、anode socket
Lamp resource 64pcs 1.5W RGB 3-in-1 LED
Outside size
1050*75*120mm
N.W 3.5kg
Loading...