Impulse PMX-090T User Manual

DM&P Vortex86MX+ Panel PC with 9” TFT LCD
Model:
PMX-090T-5A / PM X-090T-8A PMX-090T-5A-512 / PMX-090T-8A-512
(Revision 1.0A)
i
Revision
Date Version Description
2012/11/20 Version 1.0 Initial Release
i
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
Copyright
The information in this manual is subject to change without notice for continuous improvement in the product. All rights are reserved. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this document. And makes no commitment to update or to keep current the information contained in this manual.
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part, in any form or by any means without the prior written permission of the ICOP Technology Inc.
Copyright 2012 ICOP Technology Inc.
Manual No. IUMPMX090-01 Ver. 1 .0A Nov, 2012

Trademarks Ac knowledgm en

Vortex86MX is the registered trademark of ICOP Technology Inc. Other brand names or product names appearing in this document are the properties and registered trademarks of their respective owners. All names mentioned herewith are served for identification purpose only.

Safety Informat ion

Read these Safety instructions carefully. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
Do not expose your Panel PC to rain or moisture, in order to prevent shock
and fire hazard.
Keep PMX-090T away from humidity. Do not open the cabinet to avoid electrical shock. Refer to your nearest
dealer for qualified personnel servicing.
Never touch un-insulated terminals or wire unless your power adaptor is
disconnected.
Locate your Panel PC as close as possible to the socket outline for easy access
and to avoid force caused by entangling of your arms with surrounding cables from the Panel PC.
USB connectors are not supplied with Limited Power Sources. If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
DO NOT ATTEMPT TO OPEN OR TO DISASSEMBLE THE CHASSIS (ENCASING) OF THIS
PRODUCT. PLEASE CONTACT YOUR DEALER FO R SERVICING FROM QUALIFIED TECHNICIAN.
ii
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

Table of Contents

1 General Information .............................................................................. 3
1.1 Product Description ...................................................... 1
1.2 Product Specification ................................................... 2
1.3 Inspection standard for TFT-LCD Panel ........................ 4
1.4 Product Dimension ....................................................... 7
1.5 Ordering Information ................................................... 8
1.6 Packing List ................................................................... 8
2 System Installation ................................................................................ 9
2.1 CPU Board Outline........................................................ 9
2.2 Connector Summary .................................................. 10
2.3 Connector Pin Assignments........................................ 11
2.4 External I/O Overview ................................................ 13
2.5 External I/O Pin Assignment ....................................... 14
2.6 System Mapping ......................................................... 16
2.7 Watchdog Timer ......................................................... 20
3 Driver Installation ................................................................................ 21
3.1 PMX-090T Development Note ................................... 22
3.2 BIOS Default setting ................................................... 24
Warranty ......................................................................................................... 25
iii
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

1 .Gener al In formatio n

1.1 Product Description

PMX-090T is an ultra-compact platform for the present demanding
embedded and productive applications. It has new Vortex86MX SoC CPU which
consumes only minimum power requirement when running at 1GHz, and DDR2
memory provides faster data transfer rate. By using 9” TFT LCD, PMX-090T
becomes the perfect choice for a limited budget. In additional, the integrated
10/100M Ethernet port supplies the communication capability which makes
PMX-090T can be more widely used when running with Linux, Windows CE, and
Windows XP environment to become the perfect solution for system integration.
1
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

1.2 Product Specification

Tabl e 1-1 Product Specification
CPU Board Specifications
CPU DM&P Vortex86MX 1GHz
Cache
L1:16KB I-Cache, 16KB D-Cache
L2: 256KB Cache
BIOS AMI BIOS
Memory 512MB/1GB DDR2 onboard
Software programmable from
Watchdog Timer
30.5u to 512 seconds x 2 sets
LAN Integrated 10/100M Ethernet
Audio HD Audio-Realtek ALC262 CODEC
Compact Flash Type I / II slot
Internal Drives
Micro SD slot
1GB or 2GB Flash Memory onboard (Optional)
RS-232/422/485 x 1
I/O
USB ports (Ver2.0) x 2
RJ-45 Port x 1
Mechanical & Environment
Power Requirement
Single Voltage +5VDC ( 5A )
Multi Voltage +8~+35VDC ( 8A )
Power Consumption 1.5A@5VDC
Operating
0 ~ +50 ( 32 ~ +122)
Temperature
Storage
-10 ~ +60 ( 14 ~ +140)
Temperature
2
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
Operating Humidity 0% ~ 90% relative humidity, non-condensing
Dimensions 236.6 x 146 x 35mm (9.31 x 5.75 x 1.38 inches)
Weight 468g
Front Panel
IP 65
Protection
Certification CE / FCC / VCCI / Vibration
LCD Specifications
Display Type 9” TFT LCD
Backlight Unit LED
Display Resolution 1024(W) x 600(H)
Brightness (cd/m2) 300 nits
Contrast Ratio 500 : 1
Display Color 262, 144
Pixel Pitch (mm) 190.5 (H) x 189 (V)
Verti cal 120o,
Viewing Angle
Horizontal 140
o
Backlight Lifetime 25,000 hrs
Touchscreen
Type Analog Resistive
Resolution Continuous
Transmittance 80%
Controller PS / 2 interface
Software Driver DOS / Linux / WinCE / WinXP
Durability 1 million
3
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

1.3 I nspection standard for TFT-LCD Panel

Tabl e 1-2 Inspection Standard
DEFECT TYPE LIMIT Note
VISUAL DEFECT
ELECTRICAL
DEFECT
INTER
NAL
SPOT
FIBER
POLARIZER
BUBBLE
φ<0.15mm
0.15mmφ0.5mm N4
0.5mmφ
0.03mm<W0.1mm, L
5mm
1.0mmW, 1.5mm<L
φ<0.15mm
0.15mmφ0.5mm N2
0.5mmφ
Ignore
N=0
N3
N=0
Ignore
N=0
Mura It’ OK if mura is slight visible through 6%ND filter
A Grade B Grade
BRIGHT DOT
DARK DOT
TOTAL DOT
TWO ADJACENT DOT
THREE OR MORE
ADJACENT DOT
C
Area O Area
N0 N2 N2 N2 N3 N5
N2 N3 N3 N3 N5 N8
N0
Total
N4 N5 N6 N8
N1
N1
pair
pair
NOT ALLOWED
C
Area O Area
N1
N1
pair
pair
LINE DEFECT NOT ALLOWED
Total
N1
pair
Note1
Note1
Note1
Note3
Note2
Note2
Note4
(1) One pixel consists of 3 sub-pixels, including R, G, and B dot.
(Sub-pixel = Dot)
(2) LITTLE BRIGHT DOT ACCEPTITABLE UNDER 6 % ND-Filter
(3) If require G0 grand (Total dot N
0), please contact region sales.
4
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
[Note 1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter.
1. White / Black Spot
2. Polarizer Bubble
Fig 1-1
Fig 1-2
[Note 2] Bright dot is defined through 6% transmission ND Filter as following.
Fig 1-3
5
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
R
R
G
G
R G
R
R
G
G
R
G
R
R
G
G
R G
R
R
G
G
R
G
R
R
G
G
R G
R
R
G
G
R
G
R
R
Defect Dot
Adjacent Dot
A
B
C
D
[Note 3]
C Area: Center of display area
O Area: Outer of display area
[Note 4]
Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D
status) adjacent defect dots, including bright and dart adjacent dot. And they will
be counted 2 defect dots in total quantity.
(1) The defects that are not defined above and considered to be problem shall
be reviewed and discussed by both parties.
Defects on the Black Matrix, out of Display area, are not considered as a defect or
counted.
6
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

1.4 Product Dimension

Fig 1-4 Product Dimension
7
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

1.5 O rdering Informati on

Tabl e 1-3 Ordering Information
PART NUMBER DESCRIPTION
PMX-090T-5A 9” Panel PC w/1GB
DDR2 / 2USB / Line-Out / LAN / COM / CF / MicroSD /
Power Adapter
PMX-090T-8A 9” Panel PC w/1GB
DDR2 / 2USB / Line-Out / LAN / COM / CF / MicroSD /
8-35 DC Support
PMX-090T-5A-512 9” Panel PC w/512MB
DDR2 / 2USB / Line-Out / LAN / COM / CF / MicroSD /
Power Adapter
PMX-090T-8A-512 9” Panel PC w/512MB
DDR2 / 2USB / Line-Out / LAN / COM / CF / MicroSD /
8-35 DC Support

1.6 Packi ng List

Tabl e 1-4 Packing List
PART NUMBER PACKAGE
PMX-090T-5A PMX-090T-5A Power-20W-3PIN
PMX-090T-8A PMX-090T-8A
PMX-090T-5A-512 PMX-090T-5A-512 Power-20W-3PIN
PMX-090T-8A-512 PMX-090T-8A-512
WLAN KIT (Optional)
USB-WLAN-IPEX-KIT WIRELESS-
ANTENNA-157
WIRELESS-
CABLE-150MM
8
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

2 .System Installation

2.1 CPU Board Outline

Fig 2-1 PMX CPU Board
9
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

2.2 Connector Summ ary

Tabl e 2-1 Summary Table
Nbr Description Type of Connections Pin nbrs.
J1 CF Master/Slave Switch Slide Switch ON/OFF
J3 USB External USB Connector 6-pin
J4 USB External USB Connector 6-pin
J5 USB (Optional) 2.0mm 5-pin wafer 5-pin
J8 PS/2 Keyboard 2.54mm 5-pin box header 5-pin
J9 PS/2Keyboard External Mini DIN Socket 6-pin
J10 COM2(RS232/422/485) External D-Sub Male Connector 9-pin
J14 VGA 2.0mm 10-pin box header 10-pin
J18 Micro SD Card Socket Micro SD socket
J23 Audio Line-Out 1.25mm Phone Jack
J24 Audio Mic-In 2.0mm 4-pin wafer 4-pin
J25 COM3 (TX, RX) 1.25mm 3-pin wafer 3-pin
J26 COM4 (TX, RX 1.25mm 3-pin wafer 3-pin
J30 SOM CPU Board Socket SOM CPU Board Socket 200-pin
J31 4-Wires Touch connector 1.25mm 4-pin wafer 4-pin
J32 USB (Wi-Fi Optional) Internal USB Connector 6-pin
RJ45 Ethernet External RJ45 Connector 8-pin
PWR Power Connector (5A) External Mini DIN Socket 3-pin
PWR Power Connector (8A) External Power Plug 2-pin
CF1 CF Card Socket CF Type I/II Socket
10
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

2.3 Connector Pi n Assignments

J1: CF Master/Slave Switch

Pin # Signal Name
On Master
OFF Slave

J3: USB

Pin # Signal Name Pin # Signal Name
1 VCC 2 USBD2-
3 USBD2+ 4 GND
5 GND 6 GND

J4: USB

Pin # Signal Name Pin # Signal Name
1 VCC 2 USBD3-

J8: PS/2 Keyboard

Pin # Signal Name Pin # Signal Name
1 KBCLK 2 KBDAT
3 NC 4 GND
5 VCC

J9: PS/2 Keyboard/Mouse

Pin # Signal Name Pin # Signal Name
1 KBCLK 2 MSCLK
3 GND 4 K B D ATA
5 MSDATA 6 VCC
7 GND 8 GND
9 GND
J10: COM1 RS232/422/485
3 USBD3+ 4 GND
5 GND 6 GND

J5: USB (Optional)

Pin # Signal Name
1 VCC
2 USBD1-
3 USBD1+
4 GND
5 GND
11
(Change setting by BIOS)
Pin # Signal Name Pin # Signal Name
DCD1/
1
422TX- /
RS485-
TXD1 /
3
422RX+
5 GND 6 DSR1
7 RTS1 8 CTS1
9 RI1
2
4
RXD1 /
422TX+ /
RS485+
DTR1 /
422RX-
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

J14: VGA

Pin # Signal Name Pin # Signal Name
1 R OUT 2 GND
3 G OUT 4 GND
5 B OUT 6 GND
7 HSYNC 8 GND
9 VSYNCD 10 GND

J24: MIC-IN

Pin # Signal Name
1 MICVREF
2 GND
3 GND
4 MIC-IN

J25: COM3 (TX, RX)

J31: 4-Wires Touch connector

Pin # Signal Name
1 Y-
2 X-
3 Y+
4 X+

J32: USB (WiFi Optional)

Pin # Signal Name Pin # Signal Name
1 VCC 2 USBD2-
3 USBD2+ 4 GND
5 GND 6 GND

PWR: Power Connector (5A)

Pin # Signal Name
Pin # Signal Name
1 GND
2 TXD3
3 RXD3

J26: COM4 (TX, RX)

Pin # Signal Name
1 GND
2 TXD4
3 RXD4
12
1 +5V
2 GND
3 NC
4 GND

PWR: Power Connector (8A)

Pin # Signal Name
1 + 8 ~ 35V
2 GND
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
{Note}
2. COM1 RS232/422/485 is selected by BIOS setting)

2.4 External I/O Overview

{ PMX-090T-8A / PMX-090T-8A-512 }

Fig 2-2 PMX-089T-8A I/O overview

{ PMX-090T-5A / PMX-090T-5A-512 }

Fig 2-3 PMX-090T-5A I/O overview
1. Wireless is optional
13
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

2.5 Ext ernal I/O Pin Assignment

Power Switch

Pin # Status
| ON
O OFF

Power Connector (5A)

Pin # Signal Name
1 +5V
2 GND
3 NC

Power Connector (8A)

Pin # Signal Name
1 +8 ~ 35V
2 GND

Audio Line-Out

USB
Pin # Signal Name
1 VCC
2 USB0-
3 USB0+
4 GND
5 GGND
6 GGND

PS/2 Keyboard/Mouse

Pin # Signal Name
1 KBCLK
2 PMCLK
3 GND
4 KB DAT
Pin # Signal Name
1 GND
2 LOUTL
3 Open Touch
4 Open Touch
5 VREFOUT
14
5 P MDAT
6 SB5V
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

J10: COM1 RS232/422/485 (Change setting by BIOS)

Pin # Signal Name Pin # Signal Name
1 DCD1/422TX-/RS485- 2 RXD1/422TX+/RS485+
3 TXD1 / 422RX+ 4 DTR1 / 422RX-
5 GND 6 DSR1
7 RTS1 8 CTS1
9 RI1

RJ45

Pin # Signal Name Pin # Signal Name
1 FTXD+ 2 FTXD-
3 FRXIN+ 4 NC
5 NC 6 FRXIN-
15
7 NC 8 NC
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
Vortex86MX Panel PC with 1GB
MDA RAM, Hercules graphics
SPI FLASH Emulation Floppy A Enable
Standard OpenHCD USB Host Controller
Standard OpenHCD USB Host Controller

2.6 System Mapping

Tabl e 2-2 Technical Data Sheet

Technical Data Sheet

Product Name PMX-090T-8A DM171C Doc.No. QMT1000014R00
Product Description
9” DDR2 / 2USB / Line-out / LAN / 1COM / CF / MicroSD
Doc. Category Confidential
Issued Date 10-08-2012

System Mapping

Memory Mapping

Address Description Usage

00000000-0009FFFF System RAM * 000A0000-000AFFFF EGA/VGA Video Memory * 000B0000-000B7FFF 000B8000-000BFFFF CGA display RAM * 000C0000-000C7FFF EGA/VGA BIOS ROM * 000C8000-000CFFFF Boot ROM enable 000CC000-000CFFFF Console Redirection enable 000D0000-000D7FFF Expansion ROM space
000D8000-000DBFFF 000DC000-000DFFFF Expansion ROM space
*
000E0000-000EFFFF USB Legacy SCSI ROM space 000F0000-000FFFFF Motherboard BIOS *
FEBD9000-FEBD90FF
FEBDA000-FEBDA0FF FEBDB400-FEBDB4FF On board Ethernet Adapter *
16
*
*
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
Host Controller
Standard Enhanced PCI to USB Host Controller
( 6117D configuration port )
command port
FEBDB800-FEBDB8FF
FEBDBC00-FEBDBCFF
Standard Enhanced PCI to USB
*
*

I/O Mapping

I/O Address Owner Usage

0000h - 000Fh DMA 8237-1 * 0010h - 0017h COM 9 0020h - 0021h P I C 8259-1 *
0022h - 0023h 002Eh - 002Fh Forward to LPC BUS
0040h - 0043h Timer counter 8254 * 0048h - 004Bh PWM counter 8254 * 004Eh - 004Fh Forward to LPC BUS 0060h Keyboard / Mouse data port * 0061h Port B + NMI control port * 0062h - 0063h 8051 download 4K addres s counter *
0064h
Indirect Access Registers
Keyboard / Mouse status /
*
*
0065h WatchDog0 reload counter * 0066h 8051 download 8bit data port * 0067h WatchDog1 reload counter * 0068h - 006Dh WatchDog1 control register * 0070h - 0071h CMOS RAM port * 0072h - 0075h MTBF control register * 0078h - 007Ch GPIO port 0,1,2,3,4 default setup * 0080h - 008Fh DMA page register * 0092h System control register *
17
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
only register
only register
SPI Flash BIOS control register (internal SPI Flash Base address)
GPIO3[0-3] )
0098h - 009Ch GPIO direction control * 00A0h - 00A1h P I C 8259-2 * 00C0h - 00DFh DMA 8237-2 * 00E0h - 00EFh DOS 4G Page access * 0170h - 0177h I DE 1 (IRQ 15) * 01F0h - 01F7h IDE0 (IRQ 14) * 0220h - 0227h COM8 Forward to LP C BUS 0228h - 022Fh COM7 Forward to LPC BUS 0238h - 023Fh COM6 Forward to LPC BUS 0278h - 027Fh Printer port (IRQ 7, DMA 0) 02E8h - 02EFh COM4 (IRQ 11) 02F8h - 02FFh COM2 (IRQ 3) 0338h - 033Fh COM5 Forward to LPC BUS
0376h 03E8h - 03EFh COM3 (IRQ 10)
IDE1 ATAPI device control write
*
03F0h - 03F7h F l oppy Disk (I RQ 6, DMA 2)
03F6h 03F8h - 03FFh COM1 (IRQ 4) *
0480h - 048Fh DMA High page register * 0490h - 0499h Instruction counter register * 04D0h - 04D1h 8259 Edge,/ level control register * 0CF8h - 0CFFh PCI configuration port * DE00h - DEFFh on board LAN *
FC00h - FC05h
FC08h - FC0Dh
18
IDE0 ATAPI device control write
External SPI BUS control register ( output pin configurable
*
*
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

IRQ#

Description

Usage

IRQ Mapping

IRQ0 Syst em Timer * IRQ1 Keyboard Controller * IRQ2 Cascade for IRQ8 - 15 IRQ3 USB * IRQ4 Serial Port 1 * IRQ5 USB * IRQ6 Unassigned IRQ7 Ethernet 10/100M LAN * IRQ8 Real Time Clock * IRQ9 USB * IRQ10 USB * IRQ11 Audio * IRQ12 Mouse * IRQ13 Math Coprocessor * IRQ14 Hard Disk Controller#1 * IRQ15 Hard Disk Controller#2 *

DMA Mapping

DMA# Description Usage

DMA0 DMA1 DMA2 Floppy Disk Controller DMA3 DMA5 DMA6 DMA7
19
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

2.7 W atchdog Timer

There are two watchdog timers in PMX-089T, we also provide DOS, Linux and
WinCE example for your reference. For more technical support, please visit:
http://tech.icop.com.tw or download the PDF file: dmp.com.tw/tech
20
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

3 .Driver Installation

VGA
The Vortex86MX processor is integrated RDC Display chip which is an ultra
low powered graphics chipset with total power consumption at around 1-1.5 W.
LAN
The Vortex86MX+ processor is integrated 10/100Mbps Ethernet controller
that supports both 10/100BASE-T and allows direct connection to your
10/100Mbps Ethernet based Local Area Network for full interaction with local
servers, wide area networks such as the Internet.
I/O and IRQ settings can be done by software with the supplied utility
software, or it can be set for Plug and Play compatibility. The controller supports:
Half / Full-Duplex Ethernet function to double channel bandwidth, auto media
detection.

AUDIO

The ALC262 series are 4-Channel High Definition Audio Codecs with UAA
(Universal Audio Architecture) featuring two 24-bit stereo DACs and three 20-bit
stereo ADCs, they are designed for high performance multimedia desktop and
laptop systems. The ALC262 series incorporates proprietary converter technology
to achieve over 100dB Signal-to-Noise ratio playback quality; easily meeting
PC2001 requirements and also bringing PC sound quality closer to consumer
electronic devices.
21
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
Operating system support
The PMX-089T provides the VGA and LAN drivers for Linux, Windows CE,
Windows XP Professional, and Windows Embedded standard (XPE). (Linux can use
with Compact Flash card on ly.)
Please get the drivers from ICOP official website: tech.icop.com.tw
PMX-089T also supports most of the popular Linux distributions, for more
detail information, please visit DMP official website:dmp.com.tw/tech/vortex86mx

3.1 PMX-090T Development Note

<Primary /Secondary IDE: Master or Slave>

1. Micro SD: Primary Master
2. CF Slot: Secondary IDE: Master or Slave (User can use slide switch (in side of
CF slot) to adjust Master or Slave

<Window CE6.0 development guide>

Windows Embedded CE 6.0 BSP, trial CE image and development notes,
please visit technical website to get more information: tech.icop.com.tw

<Linux installation note>

Please forced the IDE setting in BIOS to PIO mode before install Linux
on PMX-090
T as follows:
3. Go to the advanced BIOS setting and make the “Onboard IDE Operate
Mode” is “Legacy Mode”
22
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
4. Go to the PCI/PnP and make the “PCI IDE BusMaster” is “Disable"
< XP professional /Home /Embedded and Windows 2000
installation note >
Please visit technical website to get more information: tech.icop.com.tw

<Enhance CF to run the UDMA2/4>

Please select ICOP “ICF Card” to supporting UDMA 2/4 Mode.

<How to boot up from the Micro SD card>

1. Get into the BIOS setup Utility
2. Go to the Advanced
3. Choose Primary IDE Pin Select: SD card
4. Press “F10” to save configuration changes and exit setup
23
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
to Save configuration changes and

3.2 BI OS Default setting

If the system cannot be booted after BIOS changes are made, Please follow
below procedures in order to restore the CMOS as default setting.
Press < End > Key, when the power on
Press < Del > to enter the AMI BIOS setup
Press < F9 > to Load Optimized defaults
Press < F10 >
exit setup
24
PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD
©ICOP Technology Inc. 2012

Warranty

This product is warranted to be in good working order for a period of one
year from the date of purchase. Should this product fail to be in good working
order at any time during this period, we will, at our option, replace or repair it at
no additional charge except as set forth in the following terms. This warranty does
not apply to products damaged by misuse, modifications, accident or disaster.
Vendor assumes no liability for any damages, lost profits, lost savings or any other
incidental or consequential damage resulting from the use, misuse of, originality
to use this product. Vendor will not be liable for any claim made by any other
related party. Return authorization must be obtained from the vendor before
returned merchandise will be accepted. Authorization can be obtained by calling
or faxing the vendor and requesting a Return Merchandise Authorization (RMA)
number. Returned goods should always be accompanied by a clear problem
description.
All Trademarks appearing in this manuscript are registered trademark of their respective owners.
All Specifications are subject to change without notice.
25
Loading...