Impex MP-4500 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Pack

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

MARCY® PLATINUM

CORNER GYM

MP-4500

Model

MP-4500

Retain This

Manual for

Reference

10-25-06

OWNER'S
MANUAL

IMPEX® INC.

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

HARDWARE PACK……….....…....................................................................... 4

ASSEMBLY INSTRUCTIONS...............................................................….......... 7

PARTS LIST…………………………………………………………….……….……. 34
RESISTANCE CHART………………………………………………………………. 35

WARRANTY.................................................................................................… 36

ORDERING PARTS......................................................................................... 36

BEFORE YOU BEGIN

Thank you for selecting the MARCY PLATINUM MP-4500 CORNER GYM by
IMPEX
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please call our
TOLL-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.

®

INC. For your safety and benefit, read this manual carefully before

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever
you operate a piece of exercise equipment. Be sure to read the entire manual before you
assemble or operate your machine. In particular, note the following safety precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the same station.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

CARE AND MAINTENANCE

1. Lubricate moving parts with WD-40 or light oil periodically.

2. Inspect and tighten all parts before using the machine.

3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.

4. Maximum user’s weight: 300 lbs.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF
35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS
BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO
RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR
THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

WARNING LABEL REPLACEMENT

The warning labels shown here have been placed on the Left Base Frame and Left Upper Frame. If the labels
are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in
location shown.

3

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.

4

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.

5

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler or scale to measure the size.

6

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended two or people assembling this machine to avoid
possible injury.

STEP 1 (See Diagram 1)

A.) Place the Right Base Frame (#31) on a flat surface. Make sure there is enough space

around to assemble the machine.

B.) Insert four Guide Rods (#16) into the holes on the Right Base Frame. Secure each

Guide Rod from bottom with a M10 x ¾” Allen Bolt (#95) and Ø ¾” Washer (#100).

C.) Attach four Ø 2 3/8” x 1” Rubber Bumpers (#52) to top of the Guide Rods then slid down

to the stopper on the Guide Rods.

D.) Attach the Right Vertical Frame (#4) onto the Right Base Frame. Secure it with two M10

x 2 ¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100),
and two M10 Aircraft Nuts (#102).

E.) Attach the Butterfly Base (#13) to the Right Base Frame (#31). Attach the Front Base

Frame (#12) to the Butterfly Base (#13) from the front. Align the holes and secure them
together with two M10 x 3 ¾” Carriage Bolts (#97) from side, two M10 x 2 ¾” Carriage
Bolts (#98) from the bottom, four Ø ¾” Washers (#100), and four M10 Aircraft Nuts
(#102).

F.) Slide fourteen Weight Plates (#80) onto the rear set of Guide Rods. Make sure the

groove on the plates all face toward the back of the machine.

G.) Insert a Selector Rod (#28) into the center holes. Slide a Selector Stem (#81) onto the

two Guide Rods.

H.) Insert a Weight Selector Pin (#74) to select the number of weight plates. Each Weight

Plate weights approximately 10 lbs. Please refer to the Weight Resistance Chart in page

35.

I.) Repeat procedures F, G and H above to install the other fourteen Weight Plates onto the

front two Guide Rods.

J.) Attach the Foot Plate (#17) to the Front Base Frame (#12). Secure it with the Foot Plate

Axle (#18).

7

DIAGRAM 1

8

STEP 2 (See Diagram 2)

A.) Attach the Right Upper Frame (#1) onto the Right Vertical Frame (#4). Secure it with two M10 x 2

¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and two M10
Aircraft Nuts (#102). Do not tighten the Nuts and Bolts yet.

B.) Attach the Right Upper Frame to the four Guide Rods (#16). Secure it to each Guide Rod with

one M10 x ¾” Allen Bolt (#95) and Ø ¾” Washer (#100).
C.) Securely tighten the Nuts and Bolts previously installed.
D.) Attach the Right Seat Support (#7) to the Right Vertical Frame (#4). Secure it with two M10 x 2 ¾”

Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and two M10

Aircraft Nuts (#102).
E.) Attach the Leg Developer (#8) to the open bracket on the Right Seat Support. Secure it with one

Axle (#15), two M10 x ¾” Allen Bolts (#95), and two Ø ¾” Washers (#100).

9

STEP 3 (See Diagram 3)

A.) Attach the Front Press Base (#2) to the Right Upper Frame (#1). Secure it with one 6 ¾”

Front Press Base Axle (#29), two Ø 1 ¼” x Ø 3/8” Washers (#70), and two M10 Aircraft
Nuts (#102). Do not over tighten the Nuts; make sure the Base is able to swivel.

B.) Attach the Front Press (#3) to the Front Press Base (#2). Secure it with one 7 5/8” Front

Press Axle (#30), two Ø 1 ¼” x Ø 3/8” Washers (#70), and two M10 Aircraft Nuts (#102).
Do not over tighten the Nuts; make sure the Press Arm is able to swivel.

C.) Thread the Short T-shaped Lock Pin (#78) into the tube on the Front Press to obtain the

desired Front Press position.

D.) Attach the Backrest Board (#43) to the Backrest Support Frame (#5). Secure it with two M8

x 1 5/8” Allen Bolts (#85) and Ø 5/8” Washers (#101).

E.) Attach the Backrest Support Frame (#5) to the Right Vertical Frame (#4). Secure it with one

M10 x 4 3/8” Allen Bolt (#89), two Ø ¾” Washers (#100), and one M10 Aircraft Nut (#102).

F.) Thread a Long T-shaped Lock Pin (#77) into the hole on the Right Vertical Frame to obtain

the desired Backrest position.

10

DIAGRAM 3

11

STEP 4 (See Diagram 4)

A.) Attach the Seat Pad (#42) to the Seat Post (#6). Secure it with two M8 x 1 5/8” Allen

Bolts (#85) and Ø 5/8” Washers (#101).

B.) Insert the Seat Post into the opening on the Right Seat Support (#7). Secure it with a

Lock Knob (#73) to lock the Seat Post at desired height.

C.) Insert the Foam Tube (#23) halfway through the hole on the Leg Developer (#8). Push

two Foam Rolls (#58) onto the Tube from both ends. Plug a Foam Roll End Cap (#59)
into each end of the Tube.

DIAGRAM 4

12

STEP 5 (See Diagram 5)

A.) Attach the Right Butterfly (#10) onto the axle on the Butterfly Base (#13).
B.) Insert the Butterfly Handle (#9) into the pivot on the Right Butterfly. Secure it with one M10 x

¾” Allen Bolt (#95) and Ø 1 ¼” x Ø 3/8” Washer (#70) from the bottom. Do not over tighten
the Bolt; make sure the handle is able to swivel.

C.) Repeat Procedure A & B above to install the Left Butterfly (#11).

DIAGRAM 5

13

STEP 6 (See Diagram 6)

A.) Do not tighten all Nuts and Bolts in this Step until instructed to do so.
B.) Attach the Left Vertical Frame (#33) onto the Left Base Frame (#32). Secure it with two M10

x 2 ¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and

two M10 Aircraft Nuts (#102).
C.) Attach the Left Base Frame (#32) to the Right Base Frame (#31). Secure it with two M10 x 3

½” Carriage Bolts (#99), one 4 ½” x 2” Bracket (#26), two Ø ¾” Washers (#100), and two

M10 Aircraft Nuts (#102).

14

STEP 7 (See Diagram 7)

A.) Attach the Left Upper Frame (#34) onto the Left Vertical Frame (33). Secure it with two M10

x 2 ¾” Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and
two M10 Aircraft Nuts (#102). Do not tighten the Nuts and Bolts yet.

B.) Attach the rear of Left Upper Frame to the Right Upper Frame (#1). Secure it with two M10 x

3 ½” Carriage Bolts (#99), one 4 ½” x 2” Bracket (#26), two Ø ¾” Washers (#100), and two
M10 Aircraft Nuts (#102).

C.) Securely tighten all Nuts and Bolts previously installed.

15

STEP 8 (See Diagram 8)

A.) Attach the Left Seat Support (#35) onto the Left Base Frame (#32). Secure it with one M10 x 3 ½”

Carriage Bolt (#99), Ø ¾” W a sher (#100), and M10 Aircraft Nut (#102).

B.) Attach the Left Seat Support to the Left Vertical Frame (#33). Secure it with two M10 x 2 ¾”

Carriage Bolts (#98), one 4 ¾” x 2 ¾” Bracket (#25), two Ø ¾” Washers (#100), and two M10
Aircraft Nuts (#102).

C.) Attach the Right & Left Handle (#37& 38) to the Left Seat Support from each side. Secure them

together with two M10 x 2 ¾” Carriage Bolts (#98), Ø ¾” W ashers (#100), and M10 Aircraft Nuts
(#102).

D.) Attach a Seat Pad (#42) to the Left Seat Support. Secure it with two M8 x 2 ½” Allen Bolts (#86)

and Ø 5/8” Washers (#101).

E.) Attach a Backrest Board (#43) to the Left Vertical Frame. Secure it with two M8 x 2 ½” Allen Bolts

(#86) and Ø 5/8” Washers (#101).

DIAGRAM 8

16

STEP 9 (See Diagram 9)

A.) Attach the Leg Press Frame (#36) to the bracket on the Left Base Frame (#32). Secure it with an

Axle (#15), two M10 x ¾” Allen Bolts (#95), and two Ø ¾” Washers (#100).
B.) Insert the Leg Press Adjustment Frame (#40) into the Leg Press Frame. Thread a Lock Knob (#73)

into the Leg Press Frame to obtain the desired leg press exercise position.
C.) Attach the Leg Press Plate (#39) to the Leg Press Adjustment Frame. Secure it with one M10 x 2

5/8” Allen Bolt (#92), two Ø ¾” Washers (#100), and one M10 Aircraft Nut (#102).

DIAGRAM 9

17

STEP 10 (See Diagram 10 & Front Press Cable Loop Diagram)

A.) Attach one end of the 140” Front Press Cable (#48) to the bracket underneath the Right

Upper Frame (#1). Secure it with one M10 x 1” Allen Bolt (#94), two Ø ¾” Washers
(#100), and one M10 Aircraft Nut (#102).

B.) Draw the Cable to the opening on the Front Press Base (#2). Attach a Pulley (#67) to

the upper opening. Secure it with one M10 x 6 ¼” Allen Bolt (#88), two Ø ¾” W a shers
(#100), and one M10 Aircraft Nut (#102).

C.) Draw the Cable around the Pulley to the opening on the Right Vertical Frame (#4).

Install a Pulley to the upper opening with M10 x 3 ½” Allen Bolt (#90), two Ø 7/8” x 1”
Pulley Bushings (#53), and one M10 Aircraft Nut (#102).

D.) Draw the Cable around the Pulley and back to the lower opening on the Front Press

Base. Repeat Procedure B above to install a Pulley.

E.) Draw the Cable around the Pulley to the lower opening on the Right Vertical Frame.

Repeat Procedure C above to install another Pulley.

F.) Draw the Cable underneath the Pulley then upward to the opening on the Right Upper

Frame (#1). Repeat Procedure C above to install a Pulley.

G.) Draw the Cable around the Pulley then downward. Attach a Pulley to the top hole on the

two Double Floating Pulley Brackets (#22).

H.) Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#93), two Ø ¾” Washers (#100), and

one M10 Aircraft Nut (#102). Draw the Cable around the Pulley and upward. Let the
Brackets hanging for now.

I.) Draw the Cable upward to the open bracket underneath the Right Upper Frame. Repeat

Procedure H above to install a Pulley.

J.) Draw the Cable around the Pulley then downward in between the two Guide Rods to the

Selector Rod (#28). Fully thread the Bolt on the end of the Cable into the Selector Rod.
Use the Nut at the end of the Cable to tighten the Bolt.

18

DIAGRAM 10

19

Front Press Cable Loop Diagram

20

STEP 11 (See Diagram 11 & Lower Cable Loop Diagram)

A.) Attach the 157” Lower Cable (#46) to the lower opening on the Leg Developer (#8).

Attach a Pulley (#67) to the opening. Secure it with one M10 x 2 5/8” Allen Bolt (#92),
two Ø 7/8” x 5/8” Pulley Bushings (#56), and one M10 Aircraft Nut (#102).

B.) Draw the Cable underneath the Pulley to the open bracket on the Right Base Frame

(#31). Attach a Pulley to the bracket and secure it with one M10 x 1 ¾” Allen Bolt (#93),
two Ø ¾” Washes (#100), and one M10 Aircraft Nut (#102).

C.) Draw the Cable underneath the Pulley through the bottom opening on the Right Vertical

Frame (#4) to another open bracket on the Right Base Frame. Repeat Procedure B
above to install a Pulley.

D.) Draw the Cable around the Pulley then upward to the Double Floating Pulley Bracket

(#22) previously installed in Step-10. Install a Pulley to the Brackets on selected hole.
After completing Step-12, come back to this step and check the tension of the Cable
loop system. If the cables are too loose, move up the Pulley on the Bracket. Move
down the Pulley if the Cables are too tight.

E.) Draw the Cable around the Pulley then downward. Install a Pulley to an Angled Double

Floating Pulley Bracket (#27).

F.) Draw the Cable around the Pulley then upward to the bracket on the back of Right

Vertical Frame. Secure the Cable to the bracket with one M10 x 1” Allen Bolt (#94), two
Ø ¾” Washers (#100), and one M10 Aircraft Nut (#102). Let the Bracket hanging for
now.

G.) Connect the Shiver Bar (#19) to the Cable with a Chain (#75) and two Hooks (#76).

Replace Shiver Bar with Single Handle (#83) or Ankle Strap (#84) for various exercises.

21

DIAGRAM 11

22

Lower Cable Loop Diagram

23

STEP 12 (See Diagram 12 & Butterfly Cable Loop Diagram)

A.) Clip one end of the 96” Butterfly Cable (#45) to the open slot on the Right Butterfly (#10).

B.) Draw the Cable to the open bracket on the right side of the Right Vertical Frame (#4).

Attach a Small Pulley (#68) to the bracket.

C.) Secure it with one M10 x 1 ¾” Allen Bolt (#93), two Ø ¾” Washers (#100), and one M10

Aircraft Nut (#102).

D.) Draw the Cable around the Small Pulley to the right open bracket on the Right Base

Frame (#31). Repeat Procedure C above to install a Pulley.

E.) Draw the Cable around the Pulley then upward to the Angled Double Floating Pulley

Bracket (#27) previously installed in Step –11. Repeat Procedure C above to install a
Pulley.

F.) Draw the Cable around the Pulley then downward to the left open bracket on the Right

Base Frame. Repeat Procedure C above to install another Pulley.

G.) Draw the Cable around the Pulley to the left open bracket on the Right Vertical Frame.

Install a Small Pulley to the bracket.

H.) Draw the Cable around the Small Pulley then clip the end of the Cable to the open slot on

the Left Butterfly.

I.) Attach the Butterfly Base Cover (#21) to the Butterfly Base (#13) to cover the left and right

pivot on the Butterfly Base. Secure the Cover to the Pivot with two M10 x ¾” Allen Bolts
(#95) and Ø ¾” Washers (#100).

J.) Align the holes and secure the Cover to the Butterfly Base with two M10 x 3 3/8” Allen

Bolts (#91), four Ø ¾” Washers (#100), and two M10 Aircraft Nuts (#102).

24

25

Butterfly Cable Loop Diagram

26

STEP 13 (See Diagram 13 and Upper Cable Loop Diagram)

A.) Attach the 130’” Upper Cable (#44) to the front opening on the Left Upper Frame (#34).

Attach a Pulley (#67) to the opening. Secure it with one M10 x 3 ½” Allen Bolt (#90), two
Ø 7/8” x 1” Pulley Bushings (#53), and one M10 Aircraft Nut (#102).

B.) Draw the Cable over the Pulley along the Left Upper Frame towards the back of the

machine. Make sure the Ball Stopper on the Cable is underneath the Left Upper Frame.

C.) Draw the Cable to the opening on the back of Left Upper Frame. Repeat Procedure A

above to install a Pulley.

D.) Draw the Cable around the Pulley then downward. Attach a Pulley to a Single Floating

Pulley Bracket (#14).

E.) Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#93), two Ø ¾” Washers (#100), and

one M10 Aircraft Nut (#102). Let the Bracket hanging for now.

F.) Draw the Cable around the Pulley then upward to the first open bracket underneath the

Right Upper Frame (#1). Repeat Procedure E above to install a Pulley.

G.) Draw the Cable over the Pulley to the second open bracket under the Right Upper Frame.

Repeat Procedure E above to install another Pulley.

H.) Draw the Cable around the Pulley then downward between the two Guide Rods (#16) to

the Selector Rod (#28). Fully thread the Bolt on the end of the Cable into the Selector
Rod. Use the Nut on the end to tighten the Bolt.

I.) Connect the Lat Bar (#24) to the Upper Cable with a Chain (#75), and two Hooks (#76).

27

DIAGRAM 13

28

Upper Cable Loop Diagram

29

STEP 14 (See Diagram 14)

A.) Attach the end of the 103” Leg Press Cable (#47) to the bracket on the Leg Press

Frame (#36). Secure it with a M10 x 1 ¾” Allen Bolt (#94), two Ø ¾” Washers (#100),

and one M10 Aircraft Nut (#102).
B.) Draw the Cable to the first open bracket on the front of Left Base Frame (#32).
C.) Install a Pulley (#67) to the bracket with one M10 x 1 ¾” Allen Bolt (#93), two Ø ¾”

Washers (#100), and one M10 Aircraft Nut (#102).
D.) Draw the Cable to the opening on the bottom of Leg Press Frame. Install a Pulley to the

opening with one M10 x 2 5/8” Allen Bolt (#92), two Ø 7/8” x 5/8” Pulley Bushings (#5),

and one M10 Aircraft Nut (#102).
E.) Draw the Cable over the Pulley to the second open bracket on the Left Base Frame.

Repeat Procedure C above to install a Pulley.
F.) Draw the Cable underneath the Pulley then through the bottom of Left Seat Support

(#35) and Left Vertical Frame (#33) to the open bracket on the back of Left Base

Frame. Repeat Procedure C above to install a Pulley
G.) Draw the Cable around the Pulley then upward to the Single Floating Pulley Bracket

(#14) installed in Step-13.
H.) Connect the end of Cable to a Chain (#75) with a Hook (#76). Secure the Chain to the

Bracket with one M10 x 1” Allen Bolt (#94), two Ø ¾” Washers (#100), and one M10

Aircraft Nut (#102).
I.) Adjust the length of the Chain to adjust the tension of the Cable System.

30

DIAGRAM 14

31

Leg Press Cable Loop Diagram

32

STEP 15 (See Diagram 15)

A.) Attach four Weight Stack Covers (#41) to the Right Upper Frame (#1) and Right Base Frame (#31).
B.) Secure each Weight Stack Cover with two M10 x 5/8” Allen Bolts (#96) and Ø ¾” Washers (#100).

DIAGRAM 15

33

PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Right Upper Frame 1
2 Front Press Base 1
3 Front Press 1
4 Right Vertical Frame 1
5 Backrest Support Fame 1
6 Seat Post 1
7 Right Seat Support 1
8 Leg Developer 1
9 Butterfly Handle 2
10 Right Butterfly 1
11 Left Butterfly 1
12 Front Base Frame 1
13 Butterfly Base 1
14 Single Floating Pulley Bracket 1
15 Axle 2
16 Guide Rod 4
17 Foot Plate 1
18 Foot Plate Axle 1
19 Shiver Bar 1
20 Shiver Bar Handle 1
21 Butterfly Base Cover 1
22 Double Floating Pulley Bracket 2
23 Foam Tube 1
24 Lat Bar 1
25 4 ¾” x 2 ¾” Bracket 6
26 4 ½” x 2” Bracket 2
27 Angled Double Floating Pulley Bracket 1
28 Selector Rod 2
29 6 ¾” Front Press Base Axle 1
30 7 5/8” Front Press Axle 1
31 Right Base Frame 1
32 Left Base Frame 1
33 Left Vertical Frame 1
34 Left Upper Frame 1
35 Left Seat Support 1
36 Leg Press Frame 1
37 Right Handle 1
38 Left Handle 1
39 Leg Press Plate 1
40 Leg Press Adjustment Frame 1
41 Weight Stack Cover 4
42 Seat Pad 2
43 Backrest Board 2
44 130” Upper Cable 1
45 96” Butterfly Cable 1
46 157” Lower Cable 1
47 103” Leg Press Cable 1
48 140” Front Press Cable 1
49 Ø 1 ½” x 5/8” Rubber Bumper 2
50 Ø 1” Bushing 2
51 Ø 1 ½” x Ø 1” Washer 8
52 Ø 2 3/8” x 1” Rubber Bumper 4
53 Ø 7/8” x 1” Pulley Bushing 10
54 Ø 1” x Ø 5/8” Washer 12
55 Ø 1 ¼” x Ø 5/8” Bushing 2

56 Ø 7/8” x 5/8” Pulley Bushing 4
57 5 ½” Butterfly Handle Grip 2
58 Foam Roll 2
59 Foam Roll End Cap 2
60 Ø 1 ½” x 1” Washer 2
61 5 3/8” Grip 8
62 1” Square End Cap 4
63 2” x 2” End Cap 3
64 2” x 1” End Cap 4
65 2 ¾” x 1” End Cap 4
66 2” x 2 ¾” End Cap 3
67 Pulley 24
68 Small Pulley 2
69 Ø 1 ¾” x 1 5/8” Rubber Bumper 1
70 Ø 1 ¼” x Ø 3/8” Washer 6
71 Ø 1” Rubber Bumper 2
72 6” Grip 4
73 Lock Knob 2
74 Weight Selector Pin 2
75 Chain 3
76 Hook 5
77 Long T-shaped Lock Pin 1
78 Short T-shaped Lock Pin 1
79 Ø 2” End Cap 2
80 Weight Plate 28
81 Selector Stem 2
82 Ø 1” End Cap 2
83 Single Handle 1
84 Ankle Strap 1
85 M8 x 1 5/8” Allen Bolt 4
86 M8 x 2 ½” Allen Bolt 4
87 M6 x 5/8” Philips Screw 3
88 M10 x 6 ¼” Allen Bolt 2
89 M10 x 4 3/8” Allen Bolt 1
90 M10 x 3 ½” Allen Bolt 5
91 M10 x 3 3/8” Allen Bolt 2
92 M10 x 2 5/8” Allen Bolt 3
93 M10 x 1 ¾” Allen Bolt 17
94 M10 x 1” Allen Bolt 4
95 M10 x ¾” Allen Bolt 18
96 M10 x 5/8” Allen Bolt 8
97 M10 x 3 ¾” Carriage Bolt 2
98 M10 x 2 ¾” Carriage Bolt 16
99 M10 x 3 ½” Carriage Bolt 5
100 Ø ¾” Washer 101
101 Ø 5/8” Washer 8
102 M10 Aircraft Nut 61

34

MP-4500 WEIGHT RESISTANCE CHART

Station 1 2 3 4 5 6 7

Low Pulley 22 33 44 55 66 77 88
Lat Pull 30 40 50 60 70 80 90
Leg Developer 26 38 50 62 74 86 98
Leg Press 36 60 84 108 132 156 180
Front Press 20 34 48 62 76 90 104
Butterfly 10 16 22 28 34 40 46

WEIGHT PLATE

WEIGHT PLATE

Station 8 9 10 11 12 13 14

Low Pulley 99 110 121 132 143 154 165
Lat Pull 100 110 120 130 140 150 160
Butterfly 110 122 134 146 158 170 182
Leg Press 204 228 252 276 300 324 348
Front Press 118 132 146 160 174 188 202
Butterfly 52 58 64 70 76 82 88

*Numbers are approximate. Actual weight may vary.

*Numbers are approximate. Actual weight may vary.

*Numbers are approximate. Actual weight may vary.*Numbers are approximate. Actual weight may vary.

*Value for butterfl y is for each arm.

*Value for butterfl y is for each arm.

*Value for butterfl y is for each arm.*Value for butterfl y is for each arm.

35

IMPEX® INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, f or a period of two years on the Frame from
the date of purchase. This warranty extends only to the original purchas er. IMPEX 's obligation
under this Warranty is limited to replacing or repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or f or products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or cons equential damages aris ing out of or
in connection with the use or performance of the pr oduct or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, cos ts of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of inc idental or consequential damages. Accordingly, the above
limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is lim ited in its sc ope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state
to state.

IMPEX

14777 Don Julian

City of Industry, CA 91746

ORDERING REPLACEMENT PARTS
Replacement parts can be order ed by calling our Custom er Ser vice Department toll-free at 1-800-

999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific

standard time.

www.impex-fitness.com
[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

3. Part Number

4. Date of Purchase

®

36

INC.