Impex IGS-5100 Owner's Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Warranty

Ordering Parts

IRON GRIP STRENGTH

DELUXE SMITH MACHINE

IGS-5100

Model

IGS-5100

Retain This

Manual for

Reference

08-15-06

OWNER'S
MANUAL

IMPEX® INC.

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN..................................................................................... 1

IMPORTANT SAFETY NOTICES.................................................................... 2

SMITH MACHINE HARDWARE PACK….......…............................................. 4

SMITH MACHINE ASSEMBLY INSTRUCTIONS............................................ 8

EXPLODED DIAGRAM…………………………………………………………….. 20
SMITH MACHINE PARTS LIST………..…………………………………………. 21
MULTI-PURPOSE BENCH HARDWARE PACK………………………………… 22

MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTIONS.............................. 24

EXPLODED DIAGRAM…………………………………………………………….. 30
MULTI-PURPOSE BENCH PARTS LIST………………………………………… 31

WARRANTY.................................................................................................… 32

ORDERING PARTS......................................................................................... 32

BEFORE YOU BEGIN

Thank you for selecting the IRON GRIP STRENGTH IGS-5100 Smith Machine
by IMPEX

®

INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please call our
TOLL-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

CARE AND MAINTENANCE

1. Lubricate moving parts with WD-40 or light oil periodically.

2. Inspect and tighten all parts before using the machine.

3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.

4. Maximum user’s weight: 300 lbs.

5. Maximum weights on the rack: 600 lbs.

6. Maximum weights on Leg Developer: 100 lbs.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

WARNING LABEL PLACEMENT

The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels
are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the
labels in the location shown.

3

SMITH MACHINE HARDWARE PACK

4

SMITH MACHINE HARDWARE PACK

5

SMITH MACHINE HARDWARE PACK

6

SMITH MACHINE HARDWARE PACK

7

SMITH MACHINE ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.

STEP 1 (See Diagram 1)

A.) Do not tighten all nuts and bolts until instructed to do so.
B.) Attach one Guide Rod (#12) onto a Base Frame (#1). Secure the Guide Rod to the Base

Frame with one M10 x 1” Allen Bolt (#74) and Ø ¾” Washer (#86) from the bottom.

C.) Slide one Lower Safety Stop Frame (#90) onto the Guide Rod from the top then slide one

Safety Stop Frame (#26) onto the Guide Rod.

D.) Attach the Base Frame (#1) to the Left Vertical Frame (#3). Attach the Cross Brace (#8)

to the back of the Left Vertical Frame (#8). Align the holes and secure the Base Frame,
Left Vertical Frame, and the Cross Brace together with two M10 x 2 ¾” Carriage Bolts
(#70), two Ø ¾” Washers (#86), and two M10 Aircraft Nuts (#83).

E.) Insert the top of the Guide Rod (#12) into the tube on the Left Vertical Frame (#3). Secure

it with one M8 x 1 5/8” Allen Bolt (#76) and M8 Aircraft Nut (#75).

F.) Attach one Front Vertical Frame (#2) onto the Base Frame (#1). Secure it with two M10 x

2 ¾” Carriage Bolts (#70), one 4” x 2” Bracket (#36), two Ø ¾” Washers (#86), and two
M10 Aircraft Nuts (#83).

G.) Attach the top of the Front Vertical Frame (#2) to the top of the Left Vertical Frame (#3).

Secure it with two M10 x 1” Allen Bolts (#74) and Ø ¾” Washers (#86).

H.) Attach a Safety Hook (#91) to the Lower Safety Stop Frame (#90). Securely it with one

M10 x 1” Allen Bolt (#74), two Ø ¾” Washers (#86), and one M10 Aircraft Nut (#83).
Attach the Safety Hook into the selected hole on the back of Front Vertical Frame.

I.) Repeat Procedure B through H to install the other side.

8

DIAGRAM 1

9

STEP 2 (See Diagram 2)

A.) Attach the Rear Vertical Frame Base (#7) to the Cross Brace (#8) from the bottom. Attach

the Rear Vertical Frame (#6) onto the Cross Brace on the top. Align the holes and secure
them together with two M10 x 2 ¾” Carriage Bolts (#70), Ø ¾” Washers (#86), and M10
Aircraft Nuts (#83).

B.) Attach the Backrest Board (#34) to the Rear Vertical Frame. Secure it with two M8 x 3 ¾”

Allen Bolts (#80) and Ø 5/8” Washes (#87).

DIAGRAM 2

10

STEP 3 (See Diagram 3)

A.) Attach the Weight Glide Post (#5) to the bracket on the Rear Vertical Frame Base (#7).

Secure it with two M10 x 2” Carriage Bolts (#72), Ø ¾” Washers (#86), and M10 Aircraft
Nuts (#83).

B.) Slide the Sliding Weight Post (#22) onto the Weight Glide Post from the top. Make sure

the Cable connecting bracket on the Sliding Weight Post faced up.

C.) Attach the rear of the Upper Frame (#11) to the top of the Weight Glide Post (#5). Secure

it with two M10 x 2” Carriage Bolts (#72), Ø ¾” Washers (#86), and M10 Aircraft Nuts
(#83).

D.) Attach the Upper Frame to the Rear Vertical Frame (#6). Secure it with one M10 x 2”

Carriage Bolt (#72), Ø ¾” Washer (#86), and M10 Aircraft Nut (#83).

E.) Attach each end of the two Upper Support Frames (#9) to the two Front Vertical Frames

(#2). Secure each Upper Support Frame with one 4” Bent Bracket (#30), M10 x 3 ½” Allen
Bolt (#79), and Ø ¾” Washer (#86) to the top hole. Secure the bottom hole with one M10
x 3 ½” Carriage Bolt (#69), Ø ¾” Washer (#86), and M10 Aircraft Nut (#83).

F.) Attach the Upper Support Frames (#9) to the Upper Frame (#11) from each side. Align the

holes and secure them together with two M10 x 2” Carriage Bolts (#72), Ø ¾” Washers
(#86), and M10 Aircraft Nuts (#83).

G.) Securely tighten all Nuts and Bolts previously installed.

11

DAIGRAM 3

12

STEP 4 (See Diagram 4)
A.) Attach the Butterfly Base (#14) to the front of Rear Vertical Frame (#6). Attach the Butterfly

Pulley Bracket (#15) to the back of the Rear Vertical Frame. Align the holes and secure them
with one M10 x 2 ¾” Carriage Bolt (#72), Ø ¾” Washer (#86), and M10 Aircraft Nut (#83)
from the side. Secure it with two M10 x 3 ½” Allen Bolts (#79), four Ø ¾” Washers (#86),
and two M10 Aircraft Nuts (#83) from the back of Rear Vertical Frame.

B.) Insert the pivot on the Left Butterfly (#20) into the hole on the Butterfly Base from the bottom.

Secure it with one Lock Ring (#57), Ø 1 ½” Washer (#67), M6 x 1 ¼” Allen Bolt (#82), and
M6 Aircraft Nut (#85).

C.) Attach the Butterfly Arm Pad (#33) to the Left Butterfly. Secure it with two M8 x 2 ½” Allen

Bolts (#81) and Ø 5/8” Washers (#87).

D.) Repeat Procedures B & C above to install the other side.

DIAGRAM 4

13

CABLE LOOP DIAGRAM

14

STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach the 133” Cable (#31) to the front opening on the Upper Frame (#11). Attach a Pulley (#38)

to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#73), two Ø 1” x ¼” Pulley Bushings
(#51), and one M10 Aircraft Nut (#83). Make sure the ball stopper on the Cable is underneath the
Frame.

B.) Draw the Cable over the Pulley along the Upper Frame to the opening on the rear of Upper

Frame. Attach a Pulley to the opening. Secure it with one M10 x 2 1/8” Allen Bolt (#73), two Ø 1” x
¼” Pulley Bushings (#51), and one M10 Aircraft Nut (#83).

C.) Draw the Cable around the Pulley then downward. Attach a Pulley in between the two Double

Floating Pulley Brackets (#35). Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#77), two Ø ¾”
Washers (#86), and one M10 Aircraft Nut (#83). Let the Bracket hanging for now.

D.) Draw the Cable around the Pulley then up to the back opening on the Upper Frame. Attach a Big

Pulley (#39) to the bracket. Secure it with one M10 x 2 1/8” Allen Bolt (#73), two Ø 1” x ¼” Pulley
Bushings (#51), and one M10 Aircraft Nut (#83).

E.) Draw the Cable around the Pulley then down to the Sliding Weight Post (#22). Secure the Cable

to the Sliding Weight Post with one M10 x 1” Allen Bolt (#74), two Ø ¾” Washers (#86), and one
M10 Aircraft Nut (#83). Attach two Olympic Sleeves (#47) to the Sliding Weight Post. Attach two
Spring Clips (#46) to the Sleeves.

F.) Connect the Lat Bar (#37) to the Cable with a Short Chain (#63) and two C-Clips (#49).

15

STEP 6 (See Diagram 6 & Cable Loop Diagram)

A.) Attach one end of the 78” Butterfly Cable (#32) to the clip on the Right Butterfly (#21). Draw

the Cable to the right Butterfly Pulley Bracket (#15).

B.) Attach a Pulley (#38) to the right Bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#77),

two Ø ¾” Washers (#86), and one M10 Aircraft Nut (#83).

C.) Draw the Cable around the Pulley then downward. Attach the Cable to a Single Floating

Pulley Bracket (#23). Repeat Procedure B above to install a Pulley. Let the Bracket hanging
for now.

D.) Draw the Cable upward to the left Butterfly Pulley Bracket. Repeat Procedure B above to

install another Pulley.

E.) Draw the Cable around the Pulley they clip it to the Left Butterfly (#20).

DIAGRAM 6

16

STEP 7 (See Diagram 7 & Cable Loop Diagram)

A.) Insert the tip of the 133” Cable (#31) through the opening on the Foot Plate (#10) to the

opening on the bottom of the Rear Vertical Beam (#6).

B.) Attach a Pulley (#38) to the opening. Attach the Foot Plate (#10) to the Frame. Align the

holes and secure the Foot Plate, Rear Vertical Frame, and the Pulley with one M10 x 2
½” Allen Bolt (#78), two Ø 1” x ½” Pulley Bushings (#50), and one M10 Aircraft Nut (#83).
Secure the Foot Plate to the Frame with one M10 x 2 3/8” Carriage Bolt (#71), Ø ¾”
Washer (#86), and M10 Aircraft Nut (#83).

C.) Draw the Cable underneath the Pulley to the opening on the Rear Vertical Frame Base

(#7). Install a Pulley with a M10 x 2 1/8” Allen Bolt (#73), two Ø 1” x ¼” Pulley Bushings
(#51) and one M10 Aircraft Nut (#83). Draw the Cable around the Pulley then upward to
the Double Floating Pulley Bracket (#35) previously installed in Step-5. Install another
Pulley with one M10 x 1 ¾” Allen Bolt (#77), two Ø ¾” Washers (#86), and one M10
Aircraft Nut (#83). Note: After finishing the entire cable assembly, come back to this step
and adjust the tension of the cables. To increase the tension, move up the Pulley on the
Double Floating Pulley Brackets. To decrease the tension, move the Pulley down.

D.) Draw the Cable around the Pulley then downward to the open bracket on the back of the

Rear Vertical Frame (#6). Install another Pulley.

E.) Draw the Cable around the Pulley and upward to the Single Floating Pulley Bracket (#23)

previously installed in Step-6. Secure the Cable to the Bracket with one M10 x 1” Allen
Bolt (#74), two Ø ¾” Washers (#86), and one M10 Aircraft Nut (#83).

F.) Connect the Long Chain (#62) to the Cable with a C-clip (#49). Depends on the exercise,

connect one of the Shiver Bar (#24), V Bar (#43), Ankle Strap (#60), Single Handle (#61),
or the Triceps Rope (#45) to the Chain with another C-clip.

17

DIAGRAM 7

18

STEP 8 (See Diagram 8)

A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting

Sleeve (#13) in between the two Safety Stop Frames (#26). Align the holes and insert the
Weight Bar (#28) all the way through. Center the bar and secure it with two M8 x 3/8” Allen
Bolts (#88) on each side.

B.) Turn the safety catch hook forward on the Lifting Sleeve to secure its position on the

selected holes on the Front Vertical Frames (#2). Attach a Long Olympic Sleeve (#48) to
each end of the We ight Bar. Attach a Spring Clip (#46) to the Sleeve.

C.) Attach six Weight Posts (#27) to the Left & Right Vertical Frames (#3&4). Secure each

Weight Post with one M10 x 1” Allen Bolt (#74) and Ø ¾” Washer (#86).

D.) Attach six Olympic Sleeves (#47) to the Weight Posts. Attach six Spring Clips (#46) to the

sleeves. Insert the Left & Right Bar Holders (#16 & 18), the Left & Right Safety Catches
(#17 & 19) into the selected holes on the Front Vertical Frames (#2).

19

EXPLODED DIAGRAM

20

PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Base Frame 2 51 Ø 1” x ¼” Pulley Bushing 8
2 Front Vertical Frame 2 52 Ø 1” End Cap 2
3 Left Vertical Frame 1 53 Ø 1” Cone-shaped End Cap 12
4 Right Vertical Frame 1 54 Ø 2” End Cap 2
5 Weight Glide Post 1 55 Ø 1 1/8” x 5/8” Bushing 4
6 Rear Vertical Frame 1 56 Ø 1 ½” x 1” x Bushing 2
7 Rear Vertical Frame Base 1 57 Lock Ring 2
8 Cross Brace 1 58 Ø 1 ¾” x 5/8” Rubber Bumper 1
9 Upper Support Frame 2 59 1 ½” Sleeve 4
10 Foot Plate 1 60 Ankle Strap 1
11 Upper Frame 1 61 Single Handle 1
12 Guide Rod 2 62 Long Chain 1
13 Lifting Sleeve 1 63 Short Chain 1
14 Butterfly Base 1 64 Lat Bar Grip 2
15 Butterfly Pulley Bracket 1 65 6” Shiver Bar Handle Grip 2
16 Left Bar Holder 1 66 3 1/8” Sleeve 2
17 Left Safety Catch 1 67 Ø 1 ½” Washer 2
18 Right Bar Holder 1 68 M6 x 5/8” Philips Screw 1
19 Right Safety Catch 1 69 M10 x 3 ½” Carriage Bolt 2
20 Left Butterfly 1 70 M10 x 2 ¾” Carriage Bolt 10
21 Right Butterfly 1 71 M10 x 2 3/8” Carriage Bolt 1
22 Sliding Weight Post 1 72 M10 x 2” Carriage Bolt 8
23 Single Floating Pulley Bracket 1 73 M10 x 2 1/8” Allen Bolt 4
24 Shiver Bar 1 74 M10 x 1” Allen Bolt 16
25 Shiver Bar Handle 1 75 M8 Aircraft Nut 2
26 Safety Stop Frame 2 76 M8 x 1 5/8” Allen Bolt 2
27 Weight Post 6 77 M10 x 1 ¾” Allen Bolt 6
28 Weight Bar 1 78 M10 x 2 ½” Allen Bolt 1
29 Panel 2 79 M10 x 3 ½” Allen Bolt 4
30 4” Bent Bracket 2 80 M8 x 3 ¾” Allen Bolt 2
31 133” Cable 2 81 M8 x 2 ½” Allen Bolt 4
32 78” Butterfly Cable 1 82 M6 x 1 ¼” Allen Bolt 2
33 Butterfly Arm Pad 2 83 M10 Aircraft Nut 38
34 Backrest Board 1 84 Ø ¾” End Cap 8
35 Double Floating Pulley Bracket 2 85 M6 Aircraft Nut 2
36 4” x 2” Bracket 2 86 Ø ¾” Washer 59
37 Lat Bar 1 87 Ø 5/8” Washer 6
38 Pulley 10 88 M8 x 3/8” Allen Bolt 8
39 Big Pulley 1 89 Panel Screw 8
40 2” Square End Cap 2 90 Lower Safety Stop Frame 2
41 5 ¾” Rubber Bumper 2 91 Safety Hook 2
42 3 3/8” Rubber Bumper 2
43 V Bar 1
44 Linear Bearing 4
45 Triceps Rope 1
46 Spring Clip 10
47 Olympic Sleeve 8
48 Long Olympic Sleeve 2
49 C-clip 4
50 Ø 1” x ½” Pulley Bushing 2

21

MULTI-PURPOSE BENCH HARDWARE PACK

22

MULTI-PURPOSE BENCH HARDWARE PACK

23

MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended this machine be assembled by two or
more people to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Attach the Front Post (#3) to the Front Stabilizer (#17).
B.) Secure it with three M10 x 5/8” Allen Bolts (#40) and Ø 5/8” Washers (#39).

DIAGRAM 1

24

STEP 2 (See Diagram 2)

A.) Attach the rear of Main Seat Support (#1) to the Rear Stabilizer (#4). Secure it with two

M10 x 2 3/8” Carriage Bolts (#47), one 5 1/8” x 2 3/8” Bracket (#21), two Ø ¾” Washers
(#39), and two M10 Aircraft Nuts (#50).

B.) Attach the Wheel (#14) to the Rear Stabilizer. Secure it with one M8 x 5 1/8” Allen Bolt

(#44), two Ø 5/8” Washers (#38), and one M8 Aircraft Nut (#51).

C.) Place the Main Seat Support onto the Front Post (#3). Secure it with two M10 x 2 ¾”

Carriage Bolts (#49), one 5 1/8” x 2 ¾” Bracket (#22), two Ø ¾” Washers (#39), and two
M10 Aircraft Nuts (#50).

DIAGRAM 2

25

STEP 3 (See Diagram 3)

A.) Attach the Leg Developer Holder (#2) to the Main Seat Support (#1). Secure it with

one M10 x 5/8” Allen Bolt (#40) and Ø ¾” Washer (#39) from the top, two M10 x 3 ½”
Carriage Bolts (#48), two Ø ¾” Washers (#39), and two M10 Aircraft Nuts (#50) from
the side.

B.) Attach the Leg Developer (#12) to the Leg Developer Holder. Secure it with one Axle

(#18), two M10 x 5/8” Allen Bolts (#40), and two Ø ¾” Washers (#39).

C.) Attach an Olympic Sleeve (#28) onto the weight post on the Leg Developer. Attach a

Spring Clip (#37) to the Sleeve.

D.) Insert the Arm Curl Stand (#6) into the top opening on the Leg Developer Holder. Use

a Lock Knob (#36) to secure the Stand at desired height.

DIAGRAM 3

26

STEP 4 (See Diagram 4)

A.) Insert two Ø ½” Bushings (#52) into the holes on the Seat Bracket (#5) and align the holes to

the pivot on the Main Seat Support (#1).

B.) Attach the two Backrest Supports (#10) to the Seat Bracket and align the holes. Secure them

with a M10 x 7 ¼” Allen Bolt (#43), two Ø ¾” Washers (#39), and one M10 Aircraft Nut (#50). Do
not over tighten the Nut and Bolt. Make sure the Backrest Supports are able to swivel.

C.) Attach the Backrest Incline Support (#7) to the opening on the Main Seat Support. Use the T-

shaped Lock Pin (#15) to secure the Backrest Incline Support at the Last Hole on the end of
Support.

D.) Attach the other end of the Backrest Incline Support (#7) to the Backrest Supports (#10). Align

the holes and secure them with two M10 x 1 ¾” Allen Bolts (#42) and two Ø3/4” Washers (#39).

27

STEP 5 (See Diagram 5)

A.) Place the Seat Pad (#8) onto the Seat Bracket (#5). Secure it with four M8 x 1 5/8” Allen

Bolts (#46) and Ø 5/8” Washers (#38).

B.) Attach the Backrest Board (#9) to the Backrest Supports (#10). Secure it with four M8 x 1

5/8” Allen Bolts (#46) and Ø 5/8” Washers (#38).

C.) Attach the Arm Curl Pad (#11) to the Arm Curl Bracket (#23). Secure it with two M8 x 5/8”

Allen Bolts (#41) and ∅ 5/8” Washers (#38).

D.) Attach the Arm Curl Bracket to the bracket on the Arm Curl Stand (#6). Insert the M8 x 3 ½”

Allen Bolt (#45) through the open track on the Arm Curl Stand and the holes on the Arm Curl
Bracket and secure the Bolt with two Ø 5/8” Washers (#38) and one M8 Aircraft Nut (#51).
Do not over tighten the Nut and Bolt. The Bolt needs to be able to slide on the track freely.

DIAGRAM 5

28

STEP 6 (See Diagram 6)

A.) Insert two Foam Tubes (#16) halfway through the holes on Leg Developer (#12).
B.) Push four Vinyl Foam Rolls (#27) onto the Tubes from both ends.
C.) Push four Foam Roll End Caps (#31) into the ends.
D.) Attach the Arm Curl Handle (#19) to the back holes on the Leg Developer. Secure it with a

Lock Pin (#20). Attach the Abdominal Strap (#24) to the front holes on the Leg Developer.
Secure it with a Lock Pin (#20).

E.) Pull up and flip the Arm Curl Pad along the track to face the back of the machine when

doing abdominal exercises using the Abdominal Strap.

F.) Remove the Arm Stand and Abdominal Strap when doing Leg Developer exercises.

29

30

MULTI-PURPOSE BENCH PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Main Seat Support 1 2 Leg Developer Holder 1 3 Front Post 1 4 Rear Stabilizer 1 5 Seat Bracket 1 6 Arm Curl Stand 1 7 Backrest Incline Support 1 8 Seat Pad 1 9 Backrest Board 1 10 Backrest Support 2 11 Arm Curl Pad 1 12 Leg Developer 1 13 Ø 2” Leg Developer Bushing 2 14 Wheel 1 15 T-shaped Lock Pin 1 16 Foam Tube 2 17 Front Stabilizer 1 18 Axle 1 19 Arm Curl Handle 1 20 Lock Pin 2 21 5 1/8” x 2 3/8” Bracket 1

22 5 1/8” x 2 ¾” Bracket 1

23 Arm Curl Bracket 1
24 Abdominal Strap 1
25 Abdominal Strap Connector 1
26 Strap Buckle 1
27 Vinyl Foam Roll 4
28 Olympic Sleeve 1
29 Ø 2” Cone-shaped End Cap 2
30 Ø 1” Cone-shaped End Cap 1
31 Foam Roll End Cap 4
32 6” Grip 2
33 Sleeve 1
34 1” Square End Cap 4
35 Ø 1” End Cap 1
36 Lock Knob 1
37 Spring Clip 1
38 Ø 5/8” Washer 14
39 Ø ¾” W asher 16
40 M10 x 5/8” Allen Bolt 6
41 M8 x 5/8” Allen Bolt 2
42 M10 x 1 ¾” Allen Bolt 2
43 M10 x 7 ¼” Allen Bolt 1
44 M8 x 5 1/8” Allen Bolt 1
45 M8 x 3 ½” Allen Bolt 1
46 M8 x 1 5/8” Allen Bolt 8
47 M10 x 2 3/8” Carriage Bolt 2
48 M10 x 3 ½” Carriage Bolt 2
49 M10 x 2 ¾” Carriage Bolt 2
50 M10 Aircraft Nut 7
51 M8 Aircraft Nut 2
52 Ø ½” Bushing 2
53 Ø 1” x Ø 3/8” Bushing 4

31

IMPEX® INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX®") warrants this product to be free f rom def ects in work m ans hip and m aterial, under normal
use and service conditions, for a period of two years on the Frame f rom the date of purchase. T his warranty
extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or
repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, m isuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for pr oducts us ed f or commercial or rental purposes. No other warr anty beyond that specifically
set forth above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or consequential dam ages arising out of or in connection
with the use or performance of the product or other damages with respect to any economic loss , loss of property,
loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential
damages or whatsoever natures. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a par ticular pur pose is lim ited in its sc ope and duration to the term s set for th her ein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state to state.

Register on-line at www.impex-fitness.com

IMPEX

14777 Don Julian

City of Industry, CA 91746

ORDERING REPLACEMENT PARTS

Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.

[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

3. Part Number

4. Date of Purchase

32

®

INC.