Impex IGS 16 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Pack

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

IGS 16

PERSONAL TRAINER

Model

IGS 16

Retain This

Manual for

Reference

09-22-03

OWNER'S
MANUAL

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICE....................................................................… 2

HARDWARE PACK…….......….....................................................................… 3

ASSEMBLY INSTRUCTIONS........................................................................... 7

EXPLODED DIAGRAM……………………………………………………………… 28

PARTS LIST...................................................................................................... 29

RESISTANCE CHART…………........................................................................ 31

WARRANTY.................................................................................................…. 32

ORDERING PARTS.......................................................................................… 32

BEFORE YOU BEGIN

Thank you for selecting the IGS-16 PERSONAL TRAINER by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are
committed to provide you complete customer satisfaction. If you have
any questions, or find there are missing or damaged parts, we
guarantee you complete satisfaction through direct assistance from our
factory. To avoid unnecessary delays, please call our TOLL-FREE
customer service number. Our Customer Service Agents will provide
immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire
manual before you assemble or operate your machine. In particular, note the following
safety precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

HARDWARE PACK

3

HARDWARE PACK

4

HARDWARE PACK

5

HARDWARE PACK

6

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended this machine be assembled by two or more people to
avoid possible injury.

STEP 1 (See Diagram 1)

A.) Place the Main Base Frame (#2) on a flat surface.
B.) Attach two Pulleys (#84) to the open oblique pulley brackets on the center of the Main Base

Frame. Secure each Pulley with one M10 x 2” Allen Bolt (#102), two Ø ¾” Washers (#118),
and one M10 Aircraft Nut (#125).

C.) Attach four Pulleys (#84) to the other four open brackets on the Main Base Frame. Secure

each Pulley with one M10 x 1 ¾” Allen Bolt (#101), two Ø ¾” Washers (#118), and one M10
Aircraft Nut (#125).

DIAGRAM 1

7

STEP 2 (See Diagram 2)

A.) Attach the Main Base Frame (#2) and the Rear Base (#18) to the bottom of the Rear Vertical

Beam (#4). Align the holes and secure them together with two M10 x 3” Carriage Bolts (#105),
Ø ¾” Washers (#118), and M10 Aircraft Nuts (#125). Do not tighten the nuts and bolts yet.

B.) Attach two Pulleys (#84) to the top & bottom open brackets on the Rear Vertical Beam (#4).

Secure each Pulley with one M10 x 1 ¾” Allen Bolt (#101), two Ø ¾” Washers (#118), and one
M10 Aircraft Nut (#125).

C.) Push two Stabilizer End Caps (#86) onto each end of the base on the Rear Vertical Beam. After

completing the entire assemb ling of the machine, check the stability. If the base was not
leveled, adjust the M10 x 1” Socket Cap Screws (#109) on the Caps to level the base.

8

STEP 3 (See Diagram 3)

A.) Attach the Front Vertical Beam (#3) to the Main Base Frame (#2). Secure it with one M10 x 2 ¾”

Allen Bolt (#104), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125). Do not tighten the
nut and bolt yet.

B.) Attach a Pulley to the bracket on the upper Front Vertical Beam. Attach a L-shaped Bracket

(#28) to the Pulley. Secure them with one M10 x 2” Allen Bolt (#102), two Ø ¾” Washers (#118),
and one M10 Aircraft Nut (#125).

C.) Place two Pulleys in the two openings on the Front Vertical Beam. Secure each Pulley with one

M10 x 2 ½” Allen Bolt (#103), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).

D.) Insert a Pulley Pre-tensioner (#24) through the hole on the back of Front Vertical Beam. Secure

it with two Ø 1 1/8” x Ø ½” Washers (#120) and M12 Regular Nuts (#127).

9

STEP 4 (See Diagram 4)

A.) Attach the Seat Support (#11) to the Front Vertical Beam (#3) and Main Base Frame (#2).

Secure it to the Front Vertical Beam with one M10 x 2 ¾” Allen Bolt (#104), two Ø ¾” Washers
(#118), and one M10 Aircraft Nut (#125). Secure it to the Main Base Frame with one M10 x 4 ½”
Allen Bolt (#108), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).

B.) Attach the Leg Developer (#12) to the Seat Support. Align the holes and insert a 2 ¾” Leg

Developer Axle (#43). Secure the Axle with two M6 x 3/8” Socket Set Screws (#112). Insert a 4”
L-shaped Pin (#39) to lock the Leg Developer in place. Remove the Pin when doing Leg
Developer exercises.

C.) Insert a Foam Tube (#37) halfway through the hole on the Leg Developer. Push two Foam Rolls

(#62) onto the Tube from both ends. Push two Foam Roll End Caps (#90) into the ends.

D.) Attach a Pulley to the open bracket on the Leg Developer. Secure it with one M10 x 1 ¾” Allen

Bolt (#101), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125). Insert a M6 x 1 5/8”
Allen Bolt (#96) through the holes on the bracket and secure it with two Ø ½” Washers (#117)
and one M6 Aircraft Nut (#123).

DIAGRAM 4

10

STEP 5 (See Diagram 5)

A.) Place the Seat (#61) onto the Seat Incline Adjustment (#13). Secure it with two M10 x 1 ¾” Allen

Bolts (#101) and Ø ¾” Washers (#118).

B.) Insert the Seat Incline Adjustment into the opening on the Seat Support (#11). Use a Lock Knob

(#71) to secure the Seat at desired height.

C.) Insert a Foam Tube (#37) halfway through the hole on the Seat Incline Adjustment (#13). Push

two Foam Rolls (#62) onto the Tube from both ends. Push two Foam Roll End Caps (#90) into

the ends.
D.) Secure the Tube with one M6 x ¼” Socket Set Screw (#111).
E.) Attach the Front Stabilizer (#14) to the front opening on the Main Base Frame (#2). Secure it

with three M10 x ¾” Allen Bolts (#97) and Ø ¾” Washers (#118).
F.) Attach the Foot Plate (#31) to the Front Stabilizer. Secure it with two M10 x 1” Allen Bolts (#98),

Ø ¾” Spring Washers (#115), Ø ¾” Washers (#118), and Ø ½” Bushings (#46).
G.) Push two Stabilizer End Caps (#86) onto the Front Stabilizer (#14).

DIAGRAM 5

11

STEP6 (See Diagram 6)

A.) Slide the Sliding Pulley Frame (#21) onto the Sliding Pulley Vertical Beam (#9) from the bottom.

Use a Lock Knob (#71) to secure the Frame at desired position.
B.) Attach the Sliding Pulley Vertical Beam (#9) onto the Rear Base (#18). Secure it with two M10 x

¾” Allen Bolts (#97) and Ø ¾” Washers (#118). Do not tighten the bolts yet.
C.) Place the Upper Frame (#5) onto the Front Vertical Beam (#3). Secure it with two M10 x 4”

Carriage Bolts (#107), Ø ¾” Washers (#118), and M10 Aircraft Nuts (#125). Do not tighten the

nuts and bolts yet.
D.) Attach the Upper Frame (#5) to the Rear Vertical Frame (#4). Align them to the Sliding Pulley

Vertical Beam (#9). Secure them together with two M10 x 3” Carriage Bolts (#105), Ø ¾”

Washers (#118), and M10 Aircraft Nuts (#125). Do not tighten the nuts and bolts yet.
E.) Insert the axle on the Sliding Pulley Bracket (#22) into the pivot on the Sliding Pulley Frame

(#21). Secure it with one Ø 1 ¼” x Ø 5/8” Washer (#121) and M16 Regular Nut (#128). Make

sure the Bracket is able to swivel.

12

STEP 7 (See Diagram 7)

A.) Attach a Pulley to the front opening on the Upper Frame (#5). Secure it with one M10 x 2 ½”

Allen Bolt (#103), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125). Do not tighten
the nut and bolt yet. The Pulley needs to be removed to install the cable later.

B.) Attach the Lat Bar Holder (#19) to the Upper Frame. Secure it with one M10 x 2 ¾” Allen Bolt

(#104), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).

C.) Attach two Pulleys to the open bracket underneath the Upper Frame. Secure them with one

M10 x 2 ¾” Allen Bolt (#104), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).
Repeat the same step to install the other two Pulleys to the other open bracket underneath the
Upper Frame.

D.) Attach a Pulley to the opening on the Upper Frame and top of Sliding Pulley Vertical Beam (#9).

Secure each Pulley with one M10 x 1 ¾” Allen Bolt (#101), two Ø ¾” Washers (#118), and one
M10 Aircraft Nut (#125).

E.) Thread a Pulley Pre-tensioner (#24) into the hole underneath the Upper Frame and secure it

with one M12 Regular Nut (#127) and Ø1 1/8”xØ ½” Washer (#120). Do not tighten the nut yet.

F.) Attach a Pulley to the Adjustable Single Pulley Bracket (#25). Secure it with one M10 x 1 ¾”

Allen Bolt (#101), two Ø ¾” Washers (#118), and one M10 Aircraft Nut (#125).

G.) Insert the Adjustable Single Pulley Bracket (#25) through the hole on the Upper Frame. Secure

it with two Ø 1 1/8” x Ø ½” Washers (#120), one M12 Regular Nut (#127) and one M12 Aircraft
Nut (#126). Do not tighten the nuts yet.

13

STEP 8 (See Diagram 8)

A.) Insert the Right Butterfly Arm (#6) into the pivot on the Front Vertical Beam (#3). Secure it

with one M10 x ¾” Allen Bolt (#97), Ø ¾” Spring Washer (#115), and Ø 1 ½” x Ø ½”
Washer (#122).

B.) Insert the Butterfly Swivel Handle (#8) into the pivot tube on the Right Butterfly Arm (#6).

Secure the bottom with a Ø 1” Clip Ring (#94).

C.) Repeat the above steps to install the other side.

DIAGRAM 8

14

STEP 9 (See Diagram 9)

A.) Attach the Bench Press Base (#32) to the pivot on the Upper Frame (#5). Align the holes and

insert a 8” Bench Press Axle (#44) through the holes. Secure the Axle with two M10 x ½”
Socket Set Screws (#113).

B.) Attach the Bench Press Arm (#1) to the Bench Press Base (#32). Align the holes and insert a

8” Bench Press Axle (#44) through the holes. Secure the Axle with two M10 x ½” Socket Set
Screws (#113).

C.) Thread a T-shaped Pull Pin Set (#69) through the hole on the Bench Press Base (#32) to obtain

the desired Bench Press position.

D.) Attach two Pulleys (#84) to the open bracket on the back of Bench Press Base (#32). Secure

them with one M10 x 2 ¾” Allen Bolt (#104), two Ø ¾” Washers (#118), and one M10 Aircraft
Nut (#125).

15

STEP 10 (See Diagram 10)
A.) Attach the Backrest Adjustment Frame (#10) to the Front Vertical Beam (#3). Secure the

bottom of the Frame to the Front Vertical Beam with one M10 x 3 1/8” Allen Bolt (#106), two Ø
¾” Washers (#118), and one M10 Aircraft Nut (#125).

B.) Attach two Backrest Swivel Brackets (#38) to the pivot on the Frame. Attach the Backrest Board

(#60) to the Brackets. Secure the Board with two M10 x 1 1/8” Allen Bolts (#99) and Ø ¾”
Washers (#118).

C.) Thread a T-shaped Pull Pin Set (#69) through the hole on the Front Vertical Beam (#3) to obtain

the desired Backrest position.

D.) Attach the Angled Foam Tube (#30) to the Backrest Adjustment Frame (#10). Secure it with

one Bent Bracket (#29), M10 x 1 5/8” Allen Bolt (#100) and Ø 7/8” Bent Washer (#119).

E.) Push two Foam Rolls (#62) onto the Tube from both ends. Push two Foam Roll End Caps

(#90) into the ends.

16

STEP 11 (See Diagram 11)

A.) Align two Ø 2 ½” x 1” Rubber Bumpers (#76) onto the holes on the Main Base Frame (#2).

Insert two Guide Rods (#15) through the Bumpers and into the Base Frame. Slide 19 Weight
Plates (#48) onto the Guide Rods.

B.) Slide the Selector Stem (#47) with the Selector Rod (#36) onto the Guide Rods. Insert the

Selector Rod (#36) through the center hole.
C.) Insert a Weight Plate Selector Pin (#72) through the selected hole on the Weight Plates.
D.) Place the Top Socket Assembly (#20) onto the Guide Rods. Secure it to the Upper Frame (#5)

with two M10 x 2 ¾” Allen Bolts (#104), four Ø ¾” Washers (#118), and two M10 Aircraft Nuts

(#125).

17

STEP 12 (See Diagram 12)

A.) Attach two Pulleys to each Angled Double Floating Pulley Bracket (#26). Secure each Pulley

with one M10 x 1 ¾” Allen Bolt (#101), two ∅3/4” Washers (#118), and one M10 Aircraft Nut

(#125). Do not tighten the nuts and bolts yet. The Pulleys may need to be removed when

installing the Cables.
B.) Attach one Pulley to a Single Pulley Bracket (#23).
C.) Attach two Pulleys to the Double Floating Pulley Brackets (#27).

DIAGRAM 12

18

STEP 13 Upper Cable Looping (See Diagram 13)

A.) Slide a Ball Stopper (#70) onto the 161” Upper Cable (#52). Slide and Pull the Cable Strap

Bracket (#45) onto the Cable. Secure the Bracket with a M8 x 1 ¼” Allen Bolt (#110) and M8
Aircraft Nut (#124).

B.) Attach the tip of the Upper Cable to the Pulley on the front of the Upper Frame (#5). Insert

the Cable into the Frame through the tube to the second opening. Remove the Pulley to get
the Cable out then reinstall the Pulley.

C.) Draw the Cable around the Pulley then down to the right Pulley on the back of the Bench

Press Base (#32). Draw the Cable around the right Pulley then to the Pulley on the front of
the Front Vertical Beam (#3).

D.) Draw the Cable around the Pulley then back to the left Pulley on the back of the Bench Press

Base (#32).

E.) Draw the Cable around the left Pulley then to the Pulley in the upper open slot on the Front

Vertical Beam (#3).

F.) Draw the Cable underneath the Pulley then pull upward to the first right Pulley underneath

the Upper Frame. Draw the Cable over the Pulley to the second right Pulley underneath the
Upper Frame.

G.) Draw the Cable over the Pulley then pull downward. Attach the Cable to the upper Pulley on

an Angled Double Floating Pulley Bracket (#26) installed in Step12. Attach the Bracket
underneath the Pulley Pre-tensioner (#24).

H.) Draw the Cable underneath the Pulley then pull upward to the Pulley on the Adjustable

Single Pulley Bracket installed in Step-7G. Let the Double Floating Pulley Bracket (#26)

hanging for now.
I.) Draw the Cable around the Pulley then pull downward to the Selector Rod (#36).
J.) Attach the end of the Cable to a M12 x 1” Split Bolt (#42). Thread the Split Bolt through a Ø

1” Spring Washer (#116) and the ring on the Weight Plate Selector Pin (#72) into the

Selector Rod (#36).
K.) Connect the Lat Bar (#17) to the Cable Strap Bracket with a Hook (#41).
L.) Place the Lat Bar onto the Lat Bar Holder.

19

DIAGRAM 13

20

STEP 14 High-Low Station Cable Looping (See Diagram 14)

A.) Slide a Ball Stopper (#70) onto the 262” High-Low Cable (#53). Slide and Pull the Cable

Strap Bracket (#45) onto the Cable. Secure the Bracket with a M8 x 1 ¼” Allen Bolt (#110)
and M8 Aircraft Nut (#124).

B.) Attach the Cable in between the pre-assembled two Small Pulleys (#85) on the

Sliding Pulley Frame (#22). Note: The Ball Stopper should be in front of the Sliding
Pulley Frame.

C.) Draw the Cable through the Sliding Pulley Frame then pull upward to the Pulley on

the top opening of the Sliding Pulley Vertical Beam (#9).

D.) Draw the Cable over the Pulley then pull forward to the Pulley on the rear opening on

the Upper Frame (#5).

E.) Draw the Cable over the Pulley then pull downward. Attach the Cable to the Pulley

on the Single Floating Pulley Bracket (#23) installed in Step12.

F.) Draw the Cable underneath the Pulley then pull upward to the Pulley on the upper

Rear Vertical Frame (#4). Let the Single Floating Pulley Bracket hanging for now.

G.) Draw the Cable around the Pulley then drop the Cable inside the tube downward

through the Rear Vertical Frame to the Pulley on the bottom opening. Remove the
Pulley to get the Cable out then reinstall the Pulley. Draw the Cable underneath the
Pulley then pull upward to the bracket on the Sliding Pulley Frame (#21).

H.) Attach the Cable head to the bracket. Secure the Cable head in place with one M10

x 1 1/8” Allen Bolt (#99) and M10 Aircraft Nut (#125).

I.) Connect the Single Handle (#35) to the Cable Strap Bracket (#45) with a Hook (#41).

21

DIAGRAM 14

22

STEP 15 Lower & AB Cable Looping (See Diagram 15)

A.) Insert the 265” Lower Cable underneath the Pulley on the Leg Developer (#12).
B.) Draw the Cable underneath the Pulley along the Main Base Frame to the Pulley under the

Seat. Continue drawing the Cable along the Base Frame through the opening on the bottom

of the Front Vertical Beam to the Pulley on the rear of Main Base Frame.
C.) Draw the Cable underneath the Pulley then pull upward to the left Pulley underneath the

Upper Frame (#5). Draw the Cable around the Pulley then pull downward. Attach the Cable

to the upper Pulley on the Double Floating Pulley Brackets (#27) previously installed in Step-

12.

D.) Draw the Cable around the Pulley then upward to the left Pulley under the Upper Frame. Let

the Bracket hanging for now.
E.) Draw the Cable around the Pulley then downward. Attach the Cable to the upper Pulley on

an Angled Double Floating Pulley Bracket (#26) previously installed in Step-12.
F.) Draw the Cable underneath the Pulley then upward to the Pulley in the middle opening on

the Front Vertical Beam. Draw the Cable over the Pulley and through the opening.
G.) Install the Ball Stopper (#70) and the Cable Strap Bracket (#45) to the Cable. Connect a

Hook (#41) to the Cable Strap Bracket and secure with the M8 x 1 ¼” Allen Bolt (#110) and

M8 Aircraft Nut (#124) on the Bracket.
H.) Connect the AB Strap (#58) or Triceps Rope (#59) to the Hook for various exercises.
I.) Use a Hook (#41) to connect a Chain (#40) to the clip on the end of the Cable in front of the

Leg Developer (#12).
J.) Use a Hook (#41) to connect the Ankle Strap (#57), Double Handle (#34), or Shiver Bar (#33)

to the Chain for various exercises.
K.) Note: After completing the entire Cable installations, adjust the tightness of the Cable Loop

System by adjusting the height of the Pulley Pre-tensioner (#24). Lower the Pre-tensioner so

it touches the top of the Pulley Bracket.

23

DIAGRAM 15

24

STEP 16 Butterfly Cable Looping (See Diagram 16)

A.) Attach one end of the 99” Butterfly Cable (#55) to the bottom of the Right Butterfly (#6).

Secure it with the M10 x 1 5/8” Allen Bolt (#100), Ø 7/8” x ½” Spacer (#80), two Ø ¾”

Washers (#118), and one M10 Aircraft Nut (#125) on the Bracket.
B.) Remove the Cable Strap Bracket from the other end of the Cable.
C.) Pull the Cable towards the back of the machine to the right oblique Pulley on the Main Base

Frame behind the Front Vertical Beam.
D.) Draw the Cable underneath the Pulley then pull upward to the lower Pulley on the Angled

Double Floating Pulley Bracket (#26). Draw the Cable around the Pulley then downward to

the left oblique Pulley on the Main Base Frame.
E.) Draw the Cable underneath the Pulley then pull to the Left Butterfly (#7).
F.) Repeat the Step A above to secure the end Cable to the Left Butterfly.

25

STEP 17 Tension Cable looping (See Diagram 17)

A.) Thread the bolt on the 161” Tension Cable (#56) into the Single Floating Pulley Bracket (#23)

previously installed.
B.) Remove the Cable Strap Bracket from the other end of the Cable.
C.) Draw the Cable down to the oblique Pulley on the Main Base Frame. Draw the Cable

underneath the Pulley then pull upward to the lower Pulley on the Angled Double Floating

Pulley Bracket (#26) previously installed.
D.) Draw the Cable around the Pulley then pull downward to the other oblique Pulley on the Main

Base Frame.
E.) Draw the Cable underneath the Pulley then pull upward to the lower Pulley on the Double

Floating Pulley Bracket (#27) previously installed.
F.) Draw the Cable over the Pulley then pull downward to the post on the Main Base Frame.

Attach the end of the Cable to the Cable Strap Bracket (#45). Secure the Strap to the post

with one M8 x 1 ¼” Allen Bolt (#110) and M8 Aircraft Nut (#124).
G.) Securely tighten all Nuts and Bolts previously installed.
H.) Check the tightness of the Cable Loop System.

26

STEP 18 (See Diagram 18)

A.) Attach two Weight Plate Covers (#16) to the Top Socket Assembly (#20) and Main Base

Frame (#2). Secure each Weight Plate Cover with four M6 x 3/8” Allen Bolts (#95) and Ø ¾”
Nylon Washers (# 67).

DIAGRAM 18

27
28

PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Bench Press Arm 1
2 Main Base Frame 1
3 Front Vertical Beam 1
4 Rear Vertical Beam 1
5 Upper Frame 1
6 Right Butterfly 1
7 Left Butterfly 1
8 Butterfly Swivel Handle 2
9 Sliding Pulley Vertical Beam 1
10 Backrest Adjustment Frame 1
11 Seat Support 1
12 Leg Developer 1
13 Seat Incline Adjustment 1
14 Front Stabilizer 1
15 Guide Rod 2
16 Weight Stack Cover 2
17 Lat Bar 1
18 Rear Base 1
19 Lat Bar Holder 1
20 Top Socket Assembly 1
21 Sliding Pulley Frame 1
22 Sliding Pulley Bracket 1
23 Single Floating Pulley Bracket 1
24 Pulley Pre-tensioner 2
25 Adjustable Single Pulley Bracket 1
26
27 Double Floating Pulley Bracket 2
28 L-shaped Pulley Bracket 1
29 Bent Bracket 1
30 Angled Foam Tube 1
31 Foot Plate 1
32 Bench Press Base 1
33 Shiver Bar 1
34
35 Single Handle 1
36 Selector Rod 1
37 Foam Tube 2
38 Backrest Swivel Bracket 2
39 4” L-shaped Pin 1
40 Chain 1
41 Hook 5
42 M12 x 1” Split Bolt 1
43 2 ¾” Leg Developer Axle 1
44 8” Bench Press Axle 2
45 Cable Strap Bracket 6
46 Ø ½” Bushing 2
47 Selector Stem 1
48 Weight Plate 19
49 Ø 1 ¼” Bushing 8
50 Ø ¾” Bushing 2
51 Ø 1” Bushing 2
52 161” Upper Cable 1
53 262” High Low Cable 1
54 265” Lower & AB Cable 1
55 99” Butterfly Cable 1

Angled Double Floating Pulley Bracket

Double Handle

1

2

56 161” Tension Cable 1
57 Ankle Strap 1
58 AB Strap 1
59 Tricep Rope 1
60 Backrest Board 1
61 Seat 1
62 Foam Roll 6
63 Butterfly Handle Bushing 4
64 Weight Plate Bushing 38
65 Selector Stem Bushing 4
66 Ø 5/8” Bushing 2
67 Ø ¾” Nylon Washer 8
68 Sliding Frame Plastic Cap 8
69 T-shaped Pull Pin Set 2
70 Ball Stopper 3
71 Lock Knob 2
72 Weight Plate Selector Pin 1
73 Weight Cover Rubber Edge 4
74 Rubber Pad 1
75 Foot Plate Anti-slipping Pad 2
76 Ø 2 ½” x 1” Rubber Bumper 2
77 Ø 1” x 5/8” Rubber Bumper 2
78 Backrest Board Rubber Bumper 1
79 Ø 1” x 3” Rubber Bumper 2
80 Ø 7/8” x ½” Spacer 2
81 Bench Press Handle Grip 4
82 Sliding Frame Handle Grip 1
83 Butterfly Grip 4
84 Pulley 30
85 Small Pulley 2
86 Stabilizer End Cap 4
87 2” Square End Cap 11
88 1 ½” Square End Cap 1
89 2” x 1” End Cap 1
90 Foam Roll End Cap 6
91 Ø 2 3/8” End Cap 2
92 Ø 1” End Cap 8
93 2 3/8” Pin 1
94 Ø 1” Clip Ring 2
95 M6 x 3/8” Allen Bolt 8
96 M6 x 1 5/8” Allen Bolt 3
97 M10 x ¾” Allen Bolt 7
98 M10 x 1” Allen Bolt 2
99 M10 x 1 1/8” Allen Bolt 4
100 M10 x 1 5/8” Allen Bolt 3
101 M10 x 1 ¾” Allen Bolt 20
102 M10 x 2” Allen Bolt 3
103 M10 x 2 ½” Allen Bolt 5
104 M10 x 2 ¾” Allen Bolt 8
105 M10 x 3” Carriage Bolt 4
106 M10 x 3 1/8” Allen Bolt 1
107 M10 x 4” Carriage Bolt 2
108 M10 x 4 ½” Allen Bolt 1
109 M10 x 1” Socket Cap Screw 4
110 M8 x 1 ¼” Allen Bolt 4

29

111 M6 x ¼” Socket Set Screw 1
112 M6 x 3/8” Socket Set Screw 2
113 M10 x ½” Socket Set Screw 4
114 M10 x ¾” Socket Set Screw 2
115 Ø ¾” Spring Washer 4
116 Ø 1” Spring Washer 1
117 Ø ½” Washer 6
118 Ø ¾” Washer 93
119 Ø 7/8” Bent Washer 1
120 Ø 1 1/8” x Ø ½” Washer 5
121 Ø 1 ¼” x Ø 5/8” Washer 1
122 Ø 1 ½” x Ø ½” Washer 2
123 M6 Aircraft Nut 3
124 M8 Aircraft Nut 4
125 M10 Aircraft Nut 45
126 M12 Aircraft Nut 1
127 M12 Regular Nut 5
128 M16 Regular Nut 1
Allen Wrench #8 (Tool) 1
Allen Wrench #6 (Tool) 1
Allen Wrench #5 (Tool) 1
Allen Wrench #4 (Tool) 1
Allen Wrench #3 (Tool) 1

30

IGS-16 WEIGHT RESISTANCE CHART

Station

Arm Curl
Lat Pull
AB Station
Leg Developer
Bench Press
Butterfly

High Low Cable

WEIGHT PLATE

1 2 3 4 5 6 7 8 9
18 29 40 51 62 73 84 95 106
18 29 40 51 62 73 84 95 106
15 26 37 48 59 70 81 92 103
25 40 55 70 85 100 115 130 145
22 33 44 55 66 77 88 99 110

6 11 16 21 26 31 36 41 46

8 14 20 26 32 38 44 50 56

Station

Arm Curl
Lat Pull
AB Station
Leg Developer
Bench Press
Butterfly
High Low Cable

* Numbers are approximate. Actual weights may vary.
* Values for Butterfly are for each arm.

WEIGHT PLATE

10 11 12 13 14 15 16 17 18 19
117 128 139 150 161 172 183 194 205 216
117 128 139 150 161 172 183 194 205 216
114 125 136 147 158 169 180 191 202 213
160 175 190 205 220 235 250 265 280 295
121 132 143 154 165 176 187 198 209 220

51 56 61 66 71 76 81 86 91 96

62 68 74 80 86 92 98 104 110 116

31

IRON GRIP SPORT

By IMPEX FITNESS PRODUCTS

LIMITED WARRANTY

IMPEX Inc. ("IMPEX") warrants this pr oduct to be f ree fr om def ects in workm ans hip and m aterial,
under normal use and service conditions, for a per iod of two years on the Frame f rom the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for produc ts
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or cons equential damages aris ing out of or
in connection with the use or performance of the pr oduct or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, cos ts of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of inc idental or consequential damages. Accordingly, the above
limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is lim ited in its sc ope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state
to state.

ORDERING REPLACEMENT PARTS
Replacement parts can be order ed by calling our Custom er Ser vice Department toll-free at 1-800-

999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific

standard time.

[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

3. Part Number

4. Date of Purchase

Register on-line www.impex-fitness.com

IMPEX INC.

14777 Don Julian

City of Industry, CA 91746

32