Impex IGS-07 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Warranty

Ordering Parts

IGS-07

MULTI LAT/MID/LOW Machine

Model

IGS-07

Retain This

Manual for

Reference

04-22-02

OWNER'S

MANUAL

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

HARDWARE IDENTIFIER.....…....................................................................... 3

ASSEMBLY INSTRUCTIONS........................................................................... 4

EXPLODED DIAGRAM……………………………………………………………... 11
PARTS LIST……………………………………………………………………….. 12

WARRANTY.................................................................................................… 13

ORDERING PARTS......................................................................................... 13

BEFORE YOU BEGIN

Thank you for selecting the IRON GRIP SPORT IGS-07 Multi Lat/Mid/Low
Machine by IMPEX FITNESS PRODUCTS. For your safety and benefit, read
this manual carefully before using the machine. As a manufacturer, we are
committed to provide you complete customer satisfaction. If you have any
questions, or find there are missing or damaged parts, we guarantee you
complete satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service number.
Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED
BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2
3

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Adjustable Wrench and Allen Wrench
NOTE: It is strongly recommended this machine to be assembled by two or more
people to avoid possible injury.

STEP 1 (See Diagram 1)

A.) Attach the Rear Stabilizer (#33) and the Base Frame (#45) to the Main Stabilizer (#35).

Secure them with two M12 x 4” Carriage Bolts (#38), ∅ 1” Washers (#12) and M12
Aircraft Nuts (#13).

B.) Attach the Rear Vertical Beam (#19) to the Rear Stabilizer (#33). Secure it with two M12

x 1” Allen Bolts (#29) and ∅ 1” Washers (#12).

C.) Attach the Front Vertical Beam (#22) to the Base Frame (#45). Secure it with two M12 x

4” Carriage Bolts (#38), ∅ 1” Washers (#12), and M12 Aircrafts (#13).

D.) Attach the Seat Frame (#53) to the Base Frame (#45). Secure it with three M12 x 1’

Allen Bolts (#29) and ∅ 1” Washers (#12).

4