Impex GS-9 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Pack

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

POWERHOUSE

CORNER GYM

GS 9

Model

GS 9

Retain This

Manual for

Reference

10-14-03

OWNER'S
MANUAL

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

HARDWARE PACK……….....…....................................................................... 3

ASSEMBLY INSTRUCTIONS...............................................................…..........5

EXPLODED DIAGRAM……………………………………………………………….26
PARTS LIST…………………………………………………………….……….…….28
RESISTANCE CHART………………………………………………………………. 29

WARRANTY.................................................................................................… 30

ORDERING PARTS......................................................................................... 30

BEFORE YOU BEGIN

Thank you for selecting the POWERHOUSE GS-9 CORNER GYM by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual carefully
before using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please call our
TOLL-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

HARDWARE PACK

3

HARDWARE PACK

4

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended two or people assembling this machine to avoid
possible injury.

STEP 1 (See Diagram 1)

A.) Place the Right Base Frame (#46) and Left Base Frame (#87) on the floor, at a right angle to

each other. Attach the Rear Vertical Beam (#50) to the joint and align the holes. Secure the
holes with two M10 x 2 ¾” Carriage Bolts (#64), ∅ 3/4” Washers (#6) and M10 Aircraft Nuts
(#5). DO NOT tighten all the nuts and bolts yet.

Diagram 1

5

STEP 2 (See Diagram 2)

A.) Attach the Right Vertical Beam (#21) to the Right Base Frame (#46). Secure it with two M10 x

2 ½” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).

B.) Attach the Right Seat Support (#49) to the Right Vertical Beam. Secure it with one Bracket

(#7), two M10 x 2 ½” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).

C.) Attach the other end of Right Seat Support (#49) to the Right Base Frame (#46). Secure it with

one M10 x 2 ½” Carriage Bolt (#17), ∅ ¾” Washer (#6), and M10 Aircraft Nut (#5).

D.) Attach the Leg Developer (#40) to the front open bracket on the Right Seat Support. Secure it

with a Leg Developer Axle (#41), two ∅ ¾” Washers (#6), and two M10 x ¾” Allen Bolts (#37).

6

STEP 3 (See Diagram 3)

A.) Slide two ∅ 2 ½” Rubber Bumpers (#58) onto two Chromed Guide Rods (#22). Insert

the two Guide Rods into the holes on the Right Base Frame (#46). Slide the Selector
Stem (#67) onto the two Guide Rods (#22). Slide the Selector Stem over the Selector
Rod (#69). Secure the Selector Rod to the Selector Stem with two M10 x 1” Allen Bolts

(#56). DO NOT install the plates yet.
B.) Repeat the Procedure A above to install another set of Guide Rods.
C.) Place the Upper Frame (#8) over the two sets of Guide Rods then onto top of Right

Vertical Beam (#21) and Rear Vertical Beam (#50).
D.) Secure each set of Guide Rods (#22) to the Upper Frame with two M10 x 1” Allen Bolts

(#56) and ∅ ¾” Washers (#6).
E.) Secure the Right Vertical Beam (#21) to the Upper Frame with one Bracket (#7), two

M10 x 2 ½” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).
F.) Attach top of Left Vertical Beam (#77) to the Upper Frame. Attach the bottom of Left

Vertical Beam to the Left Base Frame (#87). Secure the bottom of Left Vertical Beam

with two M10 x 2 ½” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts

(#5).
G.) Secure the Left Vertical Beam (#77), Rear Vertical Beam (#50), and Upper Frame (#8)

all together with two M10 x 2 ¾” Carriage Bolts (#64), ∅ ¾” Washers (#6), and M10

Aircraft Nuts (#5).
H.) Attach the Left Seat Support (#92) to the Left Vertical Beam (#77). Secure it with one

Bracket (#7), two M10 x 2 ½” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft

Nuts (#5). Attach the other end of Left Seat Support (#92) to the Left Base Frame (#87).

Secure it with one M10 x 2 ½” Carriage Bolt (#17), ∅ ¾” Washer (#6), and M10 Aircraft

Nut (#5).
I.) Securely tighten all nuts and bolts previously installed.
J.) Carefully tilt the machine on its side. (Help of another person is a MUST.) Secure the

four Guide Rods (#22) to the Right Base Frame (#46) with four M10 x 1” Allen Bolts

(#56) from the bottom.
K.) Attach the bottom of Leg Press Frame (#84) to the bracket on the Left Base Frame

(#87). Secure it with a M12 x 3” Allen Bolt (#89), two ∅ 7/8” Washers (#71), and one

M12 Aircraft Nut (#57).
L.) Insert the Seat Incline Adjustment (#90) into the opening on the Left Seat Support (#92).

Use a Lock Knob (#47) to securely hold the desired Seat height.
M.) Insert the Leg Press Plate (#76) into the Leg Press Frame. Use a Lock Knob (#47) to

securely hold the Leg Press Plate in desired position.

7

DIAGRAM 3

8

STEP 4 (See Diagram 4)

A.) Attach the Front Press Base (#97) to the Right Base Frame (#46). Secure it with a 9 ¼”

Front Press Axle (#60), two ∅ ¾” Washers (#6), and two M10 Aircraft Nuts (#5).

B.) Attach the Front Press Frames (#63) to the Front Press Base. Secure it with four M10 x 2

½” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).

DIAGRAM 4

9

STEP 5 (See Diagram 5)

A.) Attach the Butterfly Support Frame (#18) to the front of Right Vertical Beam (#21). Attach the

Butterfly Pulley Support (#74) to the back of Right Vertical Beam. Align the holes and secure
them with two M10x2 ½” Carriage Bolts (#17), ∅¾” Washers (#6), and M10 Aircraft Nuts (#5).

B.) Insert the Axle on the Left Butterfly (#20) through the hole on a Butterfly Adjustment Frame

(#100) into the hole on the Butterfly Support Frame from the bottom. Secure the Left Butterfly,
Butterfly Adjustment Frame, and Butterfly Support Frame together with one ∅ 1 ½” Wa sher
(#16), ∅1 1/2” Lock Ring (#13), M6 x 1 3/8” Hex Socket Bolt (#12), and M6 Aircraft Nut (#14).

C.) Thread a T-shaped Pull Pin Set (#103) through the hole on Left Butterfly (#20) all the way into

the selected hole on the Butterfly Adjustment Frame (#100) to securely hold the desired Butterfly
exercise position.

D.) Attach the Butterfly Arm Pad (#27) to Left Butterfly (#20). Secure it with two M8 x 2 1/8” Allen

Bolts (#25) and Ø 5/8” Washers (#24).
E.) Repeat the procedure B, C, and D above to install the other side.
F.) Attach a Swivel Pulley Bracket (#72) to the bottom of the Butterfly Pulley Support (#74). Secure

it with a M12 x 4 ½” Allen Bolt (#70), two 7/8” Washers (#71), and one M12 Aircraft Nut (#57).

Repeat for the other side.

10

STEP 6 (See Diagram 6)

A.) Attach the Vertical Press Frame (#78) to the Rear Vertical Beam (#50). Secure it with a M10 x

4 7/8” Vertical Press Axle (#81), two ∅ ¾” Washers (#6), and two M10 x 1” Allen Bolts (#56).

B.) Place the Vertical Press Frame rest on the ∅ 1 ½” Rubber Bumper (#83).

DIAGRAM 6

11

CABLE LOOP DIAGRAM

12

STEP 7 (Upper Cable Loop & Diagram 7)

A.) Attach the 108” Upper Cable (#93) to the front opening on the Upper Frame (#8). Attach a

Pulley (#79) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#10), two Pulley
Bushings (#11), and one M10 Aircraft Nut (#5). Draw the Cable towards the back of the
machine. Note: Make sure the Ball Stopper is underneath the frame.

B.) Attach a Pulley to the bracket on the Upper Frame. Secure it with one M10x1 ¾” Allen Bolt

(#98), two ∅¾” Washers (#6), one L-shaped Pulley Bracket (#86), and M10 Aircraft Nut (#5).

C.) Pull the Cable downward. Install a Pulley with a U-shaped Pulley Bracket (#85) and a Flat

Double Floating Pulley Bracket (#59). Let the bracket hanging for now.

D.) Draw the Cable around the Pulley then upward to the second open bracket on the Upper

Frame. Install another Pulley with a U-shaped Pulley Bracket (#85).

E.) Draw the Cable around the Pulley then downward to the Selector Rod (#69). Securely thread

the end of the Cable into the Selector Rod (#69).

UPPER CABLE LOOP DIAGRAM

13

DIAGRAM 7

14

STEP 8 (See Butterfly Cable Loop & Diagram 8)

A.) Attach the 114” Butterfly Cable (#95) to the slot on the back of Left Butterfly (#20). Draw the

Cable through the slot then to the open left Swivel Pulley Bracket (#72).

B.) Attach a Pulley (#79) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#98), two ∅ ¾”

Washers (#6), and one M10 Aircraft Nut (#5).

C.) Draw the Cable around the Pulley then downward. Install a Pulley to the Angled Double

Floating Bracket (#51). Let the Bracket hanging for now.
D.) Draw the Cable upward to the right Swivel Pulley Bracket. Install another Pulley.
E.) Draw the Cable to the Right Butterfly (#26) and secure the cable end to the slot.

BUTTERFLY CABLE LOOP DIAGRAM

15

DIAGRAM 8

16

STEP 9 (See Front Press Cable Loop & Diagram 9)

A.) Attach the 224” Front Press Cable (#94) to the lower opening on the Leg Developer (#40).
B.) Attach a Pulley (#79) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#10), two

Pulley Bushings (#11), and one M10 Aircraft Nut (#5).

C.) Draw the Cable underneath the Pulley through the opening on the Right Seat Support

(#49) to the open bracket on the Right Base Frame (#46).

D.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#98), two ∅ ¾”

Washers (#6), and one M10 Aircraft Nut (#5).

E.) Continue drawing the Cable along the Right Base Frame to another open bracket. Install a

Pulley as described in Step D above. Draw the Cable around the Pulley then back to the
opening between the Front Press Base (#97).

F.) Attach a Pulley to the opening. Secure it with one M10 x 8 ¼” Allen Bolt (#62), two ∅ ¾”

Washers (#6), and one M10 Aircraft Nut (#5).

G.) Draw the Cable around the Pulley then back to the lower opening on the Right Vertical

Beam (#21). Install a Pulley with one M10 x 2 3/8” Allen Bolt (#10), two Pulley Bushings
(#11), and one M10 Aircraft Nut (#5). Draw the Cable back to the open bracket on the
back of Front Press Base.

H.) Install another Pulley as described in Step D above. Draw the Cable back through the

lower opening on the Right Vertical Beam (#21) to the open bracket on the back of the
Beam. Install another Pulley.

I.) Draw the Cable upward to the hanging Angled Double Floating Bracket (#51) previously

installed in STEP 8. Install another Pulley. Draw the Cable downward to the open bracket
on the Right Base Frame (#46). Install another Pulley with a U-shaped Pulley Bracket
(#85).

J.) Draw the Cable upward to the hanging Flat Double Floating Pulley Bracket (#59)

previously installed in STEP 7. Install another Pulley with a U-shaped Pulley Bracket (#85).

K.) Draw the Cable around the Pulley then downward and connect the end to the bracket on

the Right Base Frame with a Chain (#3) and two C-clips (#4).

L.) Adjust the tension of the Cable by adjusting the length of the Chain.

17

FRONT PRESS CABLE LOOP DIAGRAM

18

DIAGRAM 9

19

STEP 10 (See Leg Press Cable Loop & Diagram 10)

A.) Attach one end of the 97” Leg Press Cable (#96) to the open slot on the back of the Leg

Press Frame (#84). Secure it with one M10 x 1 3/8” Allen Bolt (#75), two ∅ ¾” Washers

(#6), and one M10 Aircraft Nut (#5).
B.) Draw the Cable to the front opening on the Left Seat Support (#92). Attach a Pulley to

the opening. Secure it with one M10 x 1 ¾” Allen Bolt (#98), two ∅ ¾” Washers (#6),

and one M10 Aircraft Nut (#5).
C.) Draw the Cable around the Pulley then back to the open bracket on the back of the Leg

Press Frame. Install a Pulley as described in Step B above.
D.) Draw the Cable around the Pulley then to the lower opening on the Left Seat Support.

Attach a Pulley to the opening. Secure the Pulley with one M10 x 2 3/8” Allen Bolt (#10),

two Pulley Bushings (#11), and one M10 Aircraft Nut (#5).
E.) Draw the Cable towards back of the machine through the hole on the bottom of the Left

Vertical Beam (#77) to the open bracket on the Left Base Frame (#87).
F.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#98), two ∅ ¾”

Washers (#6), one L-shaped Pulley Bracket (#86), and one M10 Aircraft Nut (#5).
G.) Pull the Cable upward and connect to the 298” Vertical Press Cable (#102) with two C-

clips (#4) and one Chain (#3). After completing the steps, adjust the length of this Chain

to adjust the tightness of the Cables.
H.) Draw the Vertical Press Cable to the opening between the Vertical Press Frame (#78).

Attach a Pulley to the opening. Secure it with one M10 x 5 ¾” Allen Bolt (#82), two ∅ ¾”

Washers (#6), and one M10 Aircraft Nut (#5).
I.) Draw the Cable around the Pulley and downward to the middle open bracket on the Left

Base Frame. Install a Pulley with a U-shaped Pulley Bracket (#85).
J.) Pull the Cable upward back to the opening on the Vertical Press Frame. Install another

Pulley as described in Step H above.
K.) Draw the Cable downward to the last open bracket on the rear of the Left Base Frame.

Install a Pulley with a U-shaped Pulley Bracket (#85).
L.) Draw the Cable upward to the last open bracket on the Upper Frame (#8). Install

another Pulley. Draw the Cable downward and securely threaded it into the Selector

Rod.

20

LEG PRESS CABLE LOOP DIAGRAM

21

DIAGRAM 10

22

STEP 11 (See Diagram 11)
A.) Place a Seat Pad (#29) onto the Left Seat Support (#92). Secure it with two M8 x 1 3/8” Allen

Bolts (#106) and ∅ 5/8” Washers (#24).
B.) Attach a Backrest Board (#28) to the Left Vertical Beam (#77). Secure it with two M8 x 2 1/8”

Allen Bolts (#25) and ∅ 5/8” Washers (#24).

DIAGRAM 11

23

STEP 12 (See Diagram 12)

A.) Place a Seat Pad (#29) onto the Right Seat Support (#49). Secure it with two M8 x 2 1/8”

Allen Bolts (#25) and ∅ 5/8” Washers (#24).
B.) Attach a Backrest Board (#28) to the Right Vertical Beam (#21). Secure it with two M8 x 2 1/8”

Allen Bolts (#25) and ∅ 5/8” Washers (#24).
C.) Insert two Foam Roll Tubes (#36) halfway through the holes on the Right Seat Support (#49)

and Leg Developer (#40). Push four Foam Rolls (#33) onto the Tubes from both sides. Plug

four ∅ 1” Round End Caps (#32) into the ends.
D.) Attach the Arm Curl Pad (#34) to the Arm Curl Stand (#35). Secure it with two M8 x 5/8” Allen

Bolts (#31) and ∅ 5/8” Washers (#24). Insert the Arm Curl Stand into the opening in front of

the seat. Use the Lock Knob (#47) on the Right Seat Support to obtain the desired position.
E.) Connect the Lat Bar (#2) to the Upper Cable with a C-clip (#4) and a Chain (#3).
F.) Connect the Arm Curl Handle (#44) to the Front Press Cable (#94) with a C-clip (#4) and a

Chain (#3).

24

STEP 13 (See Diagram 13)

A.) Securely tighten all the nuts and bolts previously installed.
B.) Before putting the Weight Plates on, now move the machine to the corner of the room or

place where you will use the machine.
C.) Lift up the Selector Rod and install a stack of 19 Weight Plates (#66). To install the plates,

hold the plate at an angle and place between the two Guide Rods then drop it down. Make

sure the grooves on the plastic covers all face up. All the Plates should interlock with each

other. See diagram below. It is strongly recommended to spray some lubricant such as WD-

40 on the two Guide Rods to minimize friction. Use the Selector Pin (#55) to select the desired

weights. The Magnet on the Pin should face up. Repeat the same procedure to install

another stack of Weight Plates.
D.) Attach four Weight Stack Covers (#23) to the machine and secure each Weight Stack Cover

with two M10 x 1” Allen Bolts (#56) and ∅ 3/4” Washers (#6).

25

26

27

PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Lat Bar Grip 2
2 Lat Bar 1
3 Chain 4
4 C-clip 6
5 M10 Aircraft Nut 52
6 ∅ ¾” Washer 88
7 Bracket 3
8 Upper Frame 1
9 1 ¾” Square End Cap 16
10 M10 x 2 3/8” Allen Bolt 4
11 Pulley Bushing 8
12 M6 x 1 3/8” Hex Socket Bolt 2
13 ∅1 1/2” Lock Ring 2
14 M6 Aircraft Nut 2
15 Butterfly Axle Sleeve 4
16 ∅ 1 ½” Washer 2
17 M10 x 2 ½” Carriage Bolt 18
18 Butterfly Support Frame 1
19 2” Square End Cap 2
20 Left Butterfly 1
21 Right Vertical Beam 1
22 Guide Rod 4
23 Weight Stack Cover 4
24 ∅ 5/8” Washer 15
25 M8 x 2 1/8” Allen Bolt 10
26 Right Butterfly 1
27 Butterfly Arm Pad 2
28 Backrest Board 2
29 Seat Pad 2
30 2” Sleeve 1
31 M8 x 5/8” Allen Bolt 2
32 ∅ 1” Round End Cap 4
33 Foam Roll 4
34 Arm Curl Pad 1
35 Arm Curl Stand 1
36 Foam Roll Tube 2
37 M10 x ¾” Allen Bolt 2
38 ∅ 1 5/8” Rubber Bumper 2
39 M6 x 5/8” Philips Screw 2
40 Leg Developer 1
41 Leg Developer Axle 1
42 Arm Curl Handle 1
43 Arm Handle Sleeve 2
44 Arm Curl Handle tube 1
45 Handle Grip 4
46 Right Base Frame 1
47 Lock Knob 3
48 1” Square End Cap 4
49 Right Seat Support 1
50 Rear Vertical Beam 1
51 Angled Double Floating Bracket 1
52 M5 Screw 2
53 Magnet Box 2

54 Magnet 2
55 Selector Pin 2
56 M10 x 1” Allen Bolt 22
57 M12 Aircraft Nut 3
58 ∅ 2 ½” Rubber Bumper 4
59 Flat Double Floating Pulley Bracket 1
60 9 ¼” Front Press Axle 1
61 ∅ 7/8” Metal Bushing 14
62 M10 x 8 ¼” Allen Bolt 1
63 Front Press Frame 2
64 M10 x 2 ¾” Carriage Bolt 4
65 Weight Plate Cover 76
66 Weight Plate 38
67 Selector Stem 2
68 Selector Stem Bushing 4
69 Selector Rod 2
70 M12 x 4 ¼” Allen Bolt 2
71 ∅7/8” Washer 6
72 Swivel Pulley Bracket 2
73 1 ½” Square End Cap 3
74 Butterfly Pulley Support 1
75 M10 x 1 3/8” Allen Bolt 1
76 Leg Press Plate 1
77 Left Vertical Beam 1
78 Vertical Press Frame 1
79 Pulley 26
80 2” x 1” End Cap 4
81 M10 x 4 7/8” Vertical Press Axle 1
82 M10 x 5 ¾” Allen Bolt 2
83 ∅ 1 ½” Rubber Bumper 1
84 Leg Press Frame 1
85 U-shaped Pulley Bracket 7
86 L-shaped Pulley Bracket 2
87 Left Base Frame 1
88 ∅ 7/8” x ∅ 5/8” Leg Press Bushing 2
89 M12 x 3” Allen Bolt 1
90 Seat Incline Adjustment 1
91 Vertical Press Grip 2
92 Left Seat Support 1
93 108” Upper Cable 1
94 224” Front Press Cable 1
95 114” Butterfly Cable 1
96 97” Leg Press Cable 1
97 Front Press Base 1
98 M10 x 1 ¾” Allen Bolt 19
99 M6 x 5/8” Philips Screw 1
100 Butterfly Adjustment Frame 2
101 Ankle Strap 1
102 298” Vertical Press Cable 1
103 T-shaped Pull Pin Set 2
104 1 ½” Square End Cap 2
105 2” x 1 ¾” Sleeve 2
106 M8 x 1 3/8” Allen Bolt 2

28

WEIGHT RESISTANCE CHART

Station 1 2 3 4 5 6 7 8 9 Low Pulley 35 45 55 65 75 85 95 105 115 Lat Pull 20 30 40 50 60 70 80 90 100 Butterfly 10 17 24 31 38 45 52 59 66 Leg Press 20 30 40 50 60 70 80 90 100 Front Press 40 50 60 70 80 90 100 110 120 Vertical Press 20 30 35 40 45 50 60 70 80

WEIGHT PLATE

WEIGHT PLATE
Station 10 11 12 13 14 15 16 17 18 19
Low Pulley 125 135 145 155 165 175 185 195 205 215
Lat Pull 110 120 130 140 150 160 170 180 190 200
Butterfly 73 80 87 94 101 108 115 122 129 136
Leg Press 110 120 130 140 150 160 170 180 190 200
Front Press 130 140 150 160 170 180 190 200 210 220
Vertical Press 90 100 110 120 130 140 150 160 170 180

*Numbers are approximate. Actual weight may vary.

*Numbers are approximate. Actual weight may vary.

*Numbers are approximate. Actual weight may vary.*Numbers are approximate. Actual weight may vary.

*Value for butterfly is for each arm.

*Value for butterfly is for each arm.

*Value for butterfly is for each arm.*Value for butterfly is for each arm.

29

IMPEX INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX") warrants this pr oduct to be f ree fr om def ects in workm ans hip and m aterial,
under normal use and service c onditions , f or a per iod of two years on the Fr ame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or f or products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or cons equential damages aris ing out of or
in connection with the use or performance of the pr oduct or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, cos ts of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of inc idental or consequential damages. Accordingly, the above
limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is lim ited in its sc ope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state
to state.

IMPEX INC.

14777 Don Julian

City of Industry, CA 91746

ORDERING REPLACEMENT PARTS
Replacement parts can be order ed by calling our Custom er Ser vice Department toll-free at 1-800-

999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific

standard time.

www.impex-fitness.com
[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

3. Part Number

4. Date of Purchase

30