Impex GD-600 Owner's Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Pack

Assembly Instruction

Parts List

Warranty

Ordering Parts

ROCKING HAMMOCK

GD-600

Model

GD-600

Retain This

Manual for

Reference

11-24-09

OWNER'S
MANUAL

IMPEX® INC.

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

HARDWARE IDENTIFIER……......…............................................................... 3

ASSEMBLY INSTRUCTIONS........................................................................... 5

OPERATION………………………………………………………………………… 11

EXPLODED DIAGRAM.........................................................................………. 12

PARTS LIST...................................................................................................... 13

WARRANTY.................................................................................................…. 14

ORDERING PARTS.....................................................................................…. 14

BEFORE YOU BEGIN

Thank you for selecting the Rocking Hammock GD-600 by IMPEX®. For
your safety and benefit, read this manual carefully before using the
Hammock. As a manufacturer, we are committed to provide you complete
customer satisfaction. If you have any questions, or find there are missing or
damaged parts, we guarantee you complete satisfaction through direct
assistance from our f act ory. DO NOT RETURN THE UNIT TO THE STORE!
To avoid unnecessary delays, please call our TOLL-FREE customer service
number. Our Customer Service Agents will provide immediate assistance to
you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

Please read the entire manual before assembling or operating the equipment. In
particular, note the following safety precautions to reduce the likelihood of injury.

1. Children must be supervised at all times and never left unattended with the unit.

2. Make sure the surfaces are free of objects that may cause tipping over.

3. Place the equipment on level ground, not less than 6 ft (1.8 m) from any structure or
obstruction such as fence, garage, house, overhanging branches, laundry lines, or
electrical wires.

4. Make sure bystanders are at least 5 feet away from the equipment while it is in motion.
No one should be allowed to walk close to, in front of, behind, or between moving
items.

5. Do not stand on the Rocking Hammock. This could cause the bed to tip over and result
in injury.

6. The Rocking Hammock is not designed to use by children.

7. Maximum user weight is 300 lbs.

8. Only one person should be using the Rocking Hammock at a time.

Care and Maintenance

1. Periodically inspect all parts. Check all bolts twice monthly during the usage season for
tightness and tighten as required. It is particularly important that this procedure be
followed at the beginning of each season.

2. Replace any worn and damaged part immediately. Check all coverings for bolts and
sharp edges twice monthly during usage season to be certain they are in place.
Replace when necessary. It is especially important to do this at the beginning of each
new season.

3. Use mild household spray cleaners and/or a damp rag to wipe clean. Do not use harsh
cleaning chemicals.

4. Sand rusted areas on tubular members and repaint using a non-lead based paint
meeting the requirements of Title 16 CFR Part 1303.

5. Disposal Instructions – The equipment can be safely disassembled and disposed
without unreasonable hazards. Call your local recycle agency regarding details of
recycling.

6. Inspect before and periodically during use for frayed ropes and torn seam. Call the
customer service department if any defects were found.

7. Inspect before and periodically during use for excessive rust, integrity of the welds, and
twist in hanging hardware. Call the customer service department if any defects were
found.

SAVE THESE INSTRUCTIONS.

2

WARNING LABEL PLACEMENT

The Warning Label shown here has been placed on the Stabilizer Frame. If the label is missing or illegible,
please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.

3

HARDWARE IDENTIFIER

Part# Description Identifier

#2 Cap Washer (Qty 16)

#3 Cover Cap (Qty 16)

#24 M8 x 5/8” Allen Bolt (Qty 16)

Tools:

#5 Allen Wrench (Qty 1)

4

ASSEMBLY INSTRUCTION

Tool Required for Assembling the Machine: #5 Allen Wrench
NOTE: It is strongly recommended that two or more people assemble this machine to avoid
possible injury.

STEP 1 (See Diagram 1)

A.) Do not tighten Bolts until instructed to do so.
B.) Attach the two Stabilizer Tubes (#11) to the two Hammock Base Frames (#4).
C.) Secure each end of the Stabilizer Tube to the Hammock Base Frame with two M8 x 5/8” Allen

Bolt (#24) and two Cap Washers (#2).

D.) NOTE: The outer lip of the Cap Washer needs to face away from frame so the head of the

Bolt could be in the recess of the Washer. The groove inside the Cap Cover shold clip onto
the lip of the Cap Washer.

DIAGRAM 1

5

Step 2 (See Diagram 2)

A.) Do not tighten Bolts until instructed to do so.
B.) Insert a Hammock Body Support Tube (#12) through the sleeve next to the pillow on

Hammock Body (#15). NOTE: The pillow needs to be on top of the Hammock Body.
C.) Insert the Right Long Support (#6) into the right opening on the Hammock Base Frame (#4).
D.) Attach right end of the Hammock Body Support Tube to the Right Long Support Frame.

Attach the left end to the Left Long Support (#5).
E.) Insert the Left Long Support into the left opening on the Hammock Base Frame.
F.) Secure the Left and Right Support to the Hammock Base Frame with two M8 x 5/8” Allen

Bolts (#24) and two Cap Washer (#2) on each side.

DIAGRAM 2

6

Step 3 (See Diagram 3)

A.) Insert the Right Short Support (#8) into right opening on the Hammock Base Frame (#4).
B.) Insert the Hammock Body Support Tube (#12) through the other open sleeve on the

Hammock Body.

C.) Attach the right end of the Hammock Body Support Tube to the Right Short Support.

Attach the other end to the Left Short Support (#7).
D.) Insert the Left Short Support into the left opening on the Hammock Base Frame.
E.) Securely tighten all Bolts in previous step and this step.

DIAGRAM 3

7

Step 4 (See Diagram 4)

A.) Insert the Support Rod (#21) and Sun Shade Rod (#20) through the sleeve on the Sun

Shade (#14).

B.) Insert each end of the Support Rod into the Left and Right Rod Holder (#18) on Sun Shade

Support Frame.

DIAGRAM 4

8

Step 5 (See Diagram 5)

A.) Insert the Sun Shade Support Frame (#13) into the Long Support Cover Caps (#17).

DIAGRAM 5

9

Step 6 (See Diagram 6)

A.) Cover all M8 x 5/8” Allen Bolts (#24) and Cap Washers (#2) with sixteen Cover Caps (#3).

DIAGRAM 6

10

OPERATION

1. Place the Rocking Hammock on flat surface.

2. Lay in the middle of the Hammock Body only, and place head on the pillow.

3. Gently sway body and the Hammock will start rocking.

4. To remove the Sun Shade just simply pull out the Support Rod from the Rod holder, and then

pull out the Sun Shade Support Frame.

11

EXPLODED DIAGRAM

12

Parts list

KEY NO. DESCRIPTION Q’ty

1 Spacer 2
2 Cap Washer 16
3 Cover Cap 16
4 Hammock Base Frame 2
5 Left Long Support 1
6 Right Long Support 1
7 Left Short Support 1
8 Right Short Support 1
9 Right Bracket 1
10 Left Bracket 1
11 Stabilizer Tube 2
12 Hammock Body Support Tube 2
13 Sun Shade Support Frame 1
14 Sun Shade 1
15 Hammock Body 1
16 Short Support Cover Cap 2
17 Long Support Cover Cap 2
18 Left Rod Holder 1
19 Right Rod Holder 1
20 Sun Shade Rod 1
21 Support Rod 2
22 M6 Nut Cap 4
23 M10 x ½” Allen Bolt 2
24 M8 x 5/8” Allen Bolt 16
25 #5 Allen Wrench (Tool) 1

13

®

IMPEX

INC.

LIMITED WARRANTY

IMPEX INC ("IMPEX®") warrants this product to be free fr om defects in workm anship and material, under
normal use and service conditions, for a period of 2 YEARS from the date of purchase. This warranty
extends only to the original purchaser. IMPEX's obligation under this W arranty is limited to replacing or
repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be
prepaid by the customer. This warranty does not extend to any product or damage to a product caused by
or attributable to freight damage, abuse, misuse, improper or abnorm al usage or repairs . No other warranty
beyond that specifically set forth above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or prof its , los s of enj oyments or us e, cos ts of r emoval, installation or other
consequential damages or whatsoever natures. Som e states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a par ticular purpose is limited in its s cope and duration to the terms set f orth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state to state.

Register on-li ne at www.impe x-fit ness.com

IMPEX

14777 Don Julian Rd.,

City of Industry, CA 91746

ORDERING REPLACEMENT PARTS

Replacement parts can be order ed by calling our Customer Servic e Department toll- free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.

[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Part

3. Part Number

4. Date of Purchase

14

®

INC.