Impex EVE-1500 User Manual
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
CORNER GYM
EVE-1500
Model
EVE-1500
Retain This
Manual for
Reference
08-17-05
OWNER'S
MANUAL
Made under license from trademark owner Everlast
Worldwide Inc., New York.
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
TABLE OF CONTENTS
BEFORE YOU BEGIN....................................................................................……….. 1
IMPORTANT SAFETY NOTICES...................................................................……….. 2
HARDWARE PACK……….....….....................................................................……….. 4
ASSEMBLY INSTRUCTIONS.........................................................................……….. 7
PARTS LIST………………………………………………………………………………….. 28
RESISTANCE CHART………….......................................................................………. 29
WARRANTY.................................................................................................…………. 30
ORDERING PARTS.......................................................................................………… 30
BEFORE YOU BEGIN
Thank you for selecting the EVERLAST EVE-1500 CORNER GYM by
IMPEX INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please call
our TOO-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
info@impex-fitness.com
1
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF
THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
WARNING LABEL REPLACEMENT
The warning labels shown here have been placed on the Left Base Frame and Right Upper Frame. If the
labels are missing or illegible, please call customer service at 1-800-999-8899 for replacements. Apply the
labels in location shown.
3
HARDWARE PACK
4
HARDWARE PACK
5
HARDWARE PACK
6
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended two or more people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Place the Right and Left Base Frames (#1 & #14) on a flat surface. Make sure there is enough
space to assemble the machine.
B.) Do not tighten the nuts and bolts until instructed to do so.
C.) Attach the Left Base Frame (#14) and the Right Base Frame (#1) to the bottom of Rear
Vertical Beam (#9). Align the holes and secure the upper hole with one M10 x 2 ½” Carriage
Bolt (#87), Ø ¾” Washer (#94), and M10 Aircraft Nut (#97). Secure the lower hole with one
M10 x 2 3/8” Allen Bolt (#84) and ∅ ¾” Washer (#94).
DIAGRAM 1
7
STEP 2 (See Diagram 2)
A.) Insert two Guide Rods (#12) into the holes on the Guide Rod Base (#10). Secure each
Guide Rod with one M10 x ¾” Allen Bolt (#80) and Ø ¾” Washer (#94) from the bottom.
B.) Attach the Guide Rod Base to the Left and Right Base Frames (#1 & #14). Secure each
side with one M10 x 2 1/8” Allen Bolt (#83) and Ø ¾” Washer (#94).
DIAGRAM 2
8
STEP 3 (See Diagram 3)
A.) Attach the Right Vertical Beam (#3) onto the Right Base Frame (#1). Secure it with
two M10 x 2 ½” Carriage Bolts (#87), Ø ¾” Washers (#94), and M10 Aircraft Nuts
(#97).
B.) Attach the Left Vertical Beam (#17) onto the Left Base Frame (#14). Secure it with
two M10 x 2 ½” Carriage Bolts (#87), Ø ¾” Washers (#94), and M10 Aircraft Nuts
(#97).
C.) Place the Right Upper Frame (#4) onto the Right Vertical Beam (#3). Secure it with
two M10 x 2 ½” Carriage Bolts (#87), one 4 3/8” x 1 ¾” Bracket (#32), two Ø ¾”
Washers (#94), and two M10 Aircraft Nuts (#97).
D.) Place the Left Upper Frame (#18) onto the Left Vertical Beam (#17). Secure it with
two M10 x 2 ½” Carriage Bolts (#87), one 4 3/8” x 1 ¾” Bracket (#32), two Ø ¾”
Washers (#94), and two M10 Aircraft Nuts (#97).
E.) Attach the rear of Right Upper Frame (#4) to the Rear Vertical Beam (#9). Attach the
rear of Left Upper Frame (#18) to the Rear Vertical Beam from the other side. Align
the holes and secure them together with one M10 x 2 ½” Carriage Bolt (#87), Ø ¾”
Washer (#94), and M10 Aircraft Nut (#97) to the lower hole. Secure the upper hole
with one M10 x 2 3/8” Allen Bolt (#84) and Ø ¾” Washer (#94).
F.) Move the machine to its final location before move on to the next step.
9
Loading...