Impex CR 5 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Resistance Chart

Warranty

Ordering Parts

MARCY CORNER GYM

CR 5

Model

MWB CR 5

Retain This

Manual for

Reference

9-20-02

OWNER'S
MANUAL

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................... 1

IMPORTANT SAFETY NOTICES..................................................................... 2

HARDWARE IDENTIFIER.....…....................................................................... 3

ASSEMBLY INSTRUCTIONS...............................................................…..........4

PARTS LIST…………………………………………………………….……….…….23
RESISTANCE CHART………………………………………………………………. 24

WARRANTY.................................................................................................… 25

ORDERING PARTS......................................................................................... 25

BEFORE YOU BEGIN

Thank you for selecting the MARCY CR5 CORNER GYM by IMPEX FITNESS
PRODUCTS. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please call our
TOLL-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. – Fri. 9 a.m. – 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply whenever
you operate a piece of exercise equipment. Be sure to read the entire manual before you
assemble or operate your machine. In particular, note the following safety precautions:

1. Keep children and pets away from the machine at all times. DO NOT

leave children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or
physician in attendance.

10. Before using the machine to exercise, always do stretching exercises to
properly warm up.

11. Never operate the machine if the machine is not functioning properly.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN.
THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS
WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING
ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS
PRODUCT.

SAVE THESE INSTRUCTIONS.

2
3

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended two or people assembling this machine to avoid
possible injury.

STEP 1 (See Diagram 1)

A.) Place the Right Base Frame (#46) and Left Base Frame (#87) on the floor, at a right angle to

each other. Attach the Rear Vertical Beam (#50) to the joint and align the holes. Secure the
holes with two M10 x 3” Carriage Bolts (#64), ∅ 3/4” Washers (#6) and M10 Aircraft Nuts (#5).
DO NOT tighten all the nuts and bolts yet.

Diagram 1

4

STEP 2 (See Diagram 2)

A.) Attach the Right Vertical Beam (#21) to the Right Base Frame (#46). Secure it with two M10 x

2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).

B.) Attach the Right Seat Support (#49) to the Right Vertical Beam (#21). Secure it with one

Bracket (#7), two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts
(#5).

C.) Attach the other end of Right Seat Support (#49) to the Right Base Frame (#46). Secure it with

one M10 x 2 ¾” Carriage Bolt (#17), ∅ ¾” Washer (#6), and M10 Aircraft Nut (#5).

D.) Attach the Leg Developer (#40) to the front open bracket on the Right Seat Support. Secure it

with a Leg Developer Axle (#41), two ∅ ¾” Washers (#6), and M10 x ¾” Allen Bolts (#37).

DIAGRAM 2

5

STEP 3 (See Diagram 3)

A.) Slide two ∅ 2 ½” Rubber Bumpers (#58) onto two Chromed Guide Rods (#58). Insert the two

Guide Rods into the holes on the Right Base Frame (#46). Slide the Selector Stem (#67) onto
the two Guide Rods (#22). Slide the Selector Stem over the Selector Rod (#69). Secure the
Selector Rod to the Selector Stem with two M10 x 1” Allen Bolts (#56). DO NOT install the

plates yet.
B.) Repeat the Procedure A above to install another set of Guide Rods.
C.) Place the Upper Frame (#8) over the two sets of Guide Rods then onto top of Right Vertical

Beam (#21) and Rear Vertical Beam (#50).
D.) Secure each set of Guide Rods (#22) to the Upper Frame with two M10 x 1” Allen Bolts (#56)

and ∅ ¾” Washers (#6).
E.) Secure the Right Vertical Beam (#21) to the Upper Frame with one Bracket (#7), two M10 x 2

¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).
F.) Attach top of Left Vertical Beam (#77) to the Upper Frame. Attach the bottom of Left Vertical

Beam to the Left Base Frame (#87). Secure the bottom of Left Vertical Beam with two M10 x 2

¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).
G.) Secure the Left Vertical Beam (#77), Rear Vertical Beam (#50), and Upper Frame (#8) all

together with two M10 x 3” Carriage Bolts (#64), ∅ ¾” Washers (#6), and M10 Aircraft Nuts

(#5).
H.) Attach the Left Seat Support (#92) to the Left Vertical Beam (#77). Secure it with one Bracket

(#7), two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).

Attach the other end of Left Seat Support (#92) to the Left Base Frame (#87). Secure it with

one M10 x 2 ¾” Carriage Bolt (#17), ∅ ¾” Washer (#6), and M10 Aircraft Nut (#5).
I.) Securely tighten all nuts and bolts previously installed.
J.) Carefully tilt the machine on its side. (Help of another person is a MUST.) Secure the four

Guide Rods (#22) to the Right Base Frame (#46) with four M10 x 1” Allen Bolts (#56).
K.) Attach the bottom of Leg Press Frame (#84) to the bracket on the Left Base Frame (#87).

Secure it with a M12 x 3” Allen Bolt (#89), two ∅ 7/8” Washers (#71), and one M12 Aircraft Nut

(#57).
L.) Attach a Leg Press Diagonal Support (#90) to each side of the Leg Press Frame. Secure them

together with two M10 x 2 ½” Carriage Bolts (#100), ∅ ¾” Washers (#6), and M10 Aircraft Nuts

(#5).

6

DIAGRAM 3

7

STEP 4 (See Diagram 4)

A.) Attach the Front Press Base (#97) to the Right Base Frame (#46). Secure it with a 9 ¼” Front

Press Axle (#60), two ∅ ¾” Washers (#6), and two M10 Aircraft Nuts (#5).
B.) Attach the Front Press Frames (#63) to the Front Press Base. Secure it with four M10 x 2 ¾”

Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).

DIAGRAM 4

8

STEP 5 (See Diagram 5)

A.) Attach the Butterfly Support Frame (#18) to the front of Right Vertical Beam (#21). Attach the

Butter Pulley Support (#74) to the back of Right Vertical Beam. Align the holes. Secure them

together with two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts

(#5).
B.) Insert the Axle on the Left Butterfly (#20) into the hole on the Butterfly Support Frame from the

bottom. Secure it with one ∅ 1 ½” Washer (#16), ∅1 3/8” Lock Ring (#13), M6 x 1 5/8” Hex

Bolt (#12), and M6 Aircraft Nut (#14). Repeat the same procedure to install the other side.
C.) Slide two Butterfly Foam Rolls (#27) onto the Butterfly Arms.
D.) Attach a Swivel Pulley Bracket (#72) to the bottom of the Butterfly Pulley Support (#74).

Secure it with a M12 x 4 ½” Allen Bolt (#70), two 7/8” Washers (#71), and one M12 Aircraft Nut

(#57). Repeat for the other side.

DIAGRAM 5

9

STEP 6 (See Diagram 6)

A.) Attach the Vertical Press Frame (#78) to the Rear Vertical Beam (#50). Secure it with a M10 x

4 7/8” Vertical Press Axle (#81), two ∅ ¾” Washers (#6), and two M10 x 1” Allen Bolts (#56).

B.) Place the Vertical Press Frame rest onto the ∅ 1 ½” Rubber Bumper (#83).

DIAGRAM 6

10

CABLE LOOP DIAGRAM

11

STEP 7 (Upper Cable Loop & Diagram 7)

A.) Attach the 108” Upper Cable (#93) to the front opening on the Upper Frame (#8). Attach a

Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley
Bushings (#11), and one M10 Aircraft Nut (#5). Draw the Cable towards the back of the
machine. Note: Make sure the Ball Stopper is underneath the frame.

B.) Attach a Pulley to the bracket on the Upper Frame. Secure it with one M10 x 2” Allen Bolt

(#98), two ∅ ¾” Washers (#6), one L-shaped Pulley Bracket (#86), and one M10 Aircraft Nut
(#5).

C.) Pull the Cable downward. Install a Pulley with a Flat Double Floating Pulley Bracket (#59). Let

the bracket hanging for now.

D.) Draw the Cable around the Pulley then upward to the second open bracket on the Upper

Frame. Install another Pulley with a U-shaped Pulley Bracket (#85).

E.) Draw the Cable around the Pulley then downward to the Selector Rod (#69). Securely thread

the end of the Cable into the Selector Rod (#69).

UPPER CABLE LOOP DIAGRAM

12

DIAGRAM 7

13

STEP 8 (See Butterfly Cable Loop & Diagram 8)

A.) Attach the 83” Butterfly Cable (#95) to the slot on the back of Left Butterfly (#20). Draw the

Cable through the slot then to the open left Swivel Pulley Bracket (#72).

B.) Attach a Pulley (#79) to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two ∅ ¾”

Washers (#6), and one M10 Aircraft Nut (#5).

C.) Draw the Cable around the Pulley then downward. Install a Pulley to the Angled Double

Floating Bracket (#51). Let the Bracket hanging for now.
D.) Draw the Cable upward to the right Swivel Pulley Bracket. Install another Pulley..
E.) Draw the Cable to the Right Butterfly (#26) and secure the cable end to the slot.

BUTTERFLY CABLE LOOP DIAGRAM

14

DIAGRAM 8

15

STEP 9 (See Front Press Cable Loop & Diagram 9)
A.) Attach the 247” Front Press Cable (#94) to the lower opening on the Leg Developer (#40).
B.) Attach a Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two

Pulley Bushings (#11), and one M10 Aircraft Nut (#5).

C.) Draw the Cable underneath the Pulley through the opening on the Right Seat Support (#49) to

the open bracket on the Right Base Frame (#46).

D.) Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two ∅ ¾” Washers

(#6), and one M10 Aircraft Nut (#5).

E.) Continue drawing the Cable along the Right Base Frame to another open bracket. Install a

Pulley as described in Step D above with a L-shaped Pulley Bracket (#86). Draw the Cable
around the Pulley then back to the opening between the Front Press Base (#97).

F.) Attach a Pulley to the opening. Secure it with one M10 x 8 ¼” Allen Bolt (#62), two ∅ ¾”

Washers (#6), and one M10 Aircraft Nut (#5).

G.) Draw the Cable around the Pulley then back to the lower opening on the Right Vertical Beam

(#21). Install another Pulley as described in Step D above. Draw the Cable back to the open
bracket on the back of Front Press Base.

H.) Install another Pulley as described in Step D above. Draw the Cable back through the lower

opening on the Right Vertical Beam (#21) to the open bracket on the back of the Beam. Install
another Pulley.

I.) Draw the Cable upward to the hanging Angled Double Floating Bracket (#51) previously

installed in STEP 8. Install another Pulley. Draw the Cable downward to the open bracket on
the Right Base Frame (#46). Install another Pulley with a U-shaped Pulley Bracket (#85).

J.) Draw the Cable upward to the hanging Flat Double Floating Pulley Bracket (#59) previously

installed in STEP 7. Install another Pulley.

K.) Draw the Cable around the Pulley then downward and connect to the Right Base Frame with a

Chain (#3) and two C-clips (#4). Adjust the tension of the Cable by adjusting the length of the
Chain.

FRONT PRESS CABLE LOOP DIAGRAM

16

DIAGRAM 9

17

STEP 10 (See Leg Press Cable Loop & Diagram 10)
A.) Attach one end of the 82” Leg Press Cable (#96) to the open slot on the back of the Leg

Press Frame (#84). Secure it with one M10 x 2 ½” Allen Bolt (#10), two ∅ ¾” Washers (#6),

and one M10 Aircraft Nut (#5).
B.) Draw the Cable to the front opening on the Left Seat Support (#92). Attach a Pulley to the

opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley Bushings (#11), and one

M10 Aircraft Nut (#6).
C.) Draw the Cable around the Pulley then back to the lower opening on the Leg Press Frame.

Install a Pulley as described in Step B above.
D.) Draw the Cable around the Pulley then towards back of the machine through the hole on the

bottom of the Left Vertical Beam (#77) to the open bracket on the Left Base Frame (#87).
E.) Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two ∅ ¾”

Washers (#6), one L-shaped Pulley Bracket (#86), and one M10 Aircraft Nut (#5).
F.) Pull the Cable upward and connect to the 298” Vertical Press Cable (#102) with two C-clips

(#4) and one Chain (#3). After completing the steps, adjust the length of this Chain to adjust

the tightness of the Cables.
G.) Draw the Vertical Press Cable to the opening between the Vertical Press Frame (#78). Attach

a Pulley to the opening. Secure it with one M10 x 5 ¾” Allen Bolt (#82), two ∅ ¾” Washers

(#6), and one M10 Aircraft Nut (#5).
H.) Draw the Cable around the Pulley and downward to the middle open bracket on the Left Base

Frame. Install a Pulley with a U-shaped Pulley Bracket (#85).
I.) Pull the Cable upward back to the opening on the Vertical Press Frame. Install another Pulley

as described in Step G above.
J.) Draw the Cable downward to the last open bracket on the rear of the Left Base Frame. Install

a Pulley with a U-shaped Pulley Bracket (#85).
K.) Draw the Cable upward to the last open bracket on the Upper Frame (#8). Install another

Pulley. Draw the Cable downward and securely threaded it into the Selector Rod.

LEG PRESS CABLE LOOP DIAGRAM

18

DIAGRAM 10

19

STEP 11 (See Diagram 11)
A.) Place a Seat Pad (#29) onto the Left Seat Support (#92). Secure it with two M8 x 2 1/8” Allen

Bolts (#25) and ∅ 5/8” Washers (#24).
B.) Attach a Backrest Board (#28) to the Left Vertical Beam (#77). Secure it with two M8 x 2 1/8”

Allen Bolts (#25) and ∅ 5/8” Washers (#24).
C.) Attach the Leg Press Plate (#76) onto the Leg Press Frame (#84). Secure it with a L-shaped

Pin (#75).

DIAGRAM 11

20

STEP 12 (See Diagram 12)

A.) Place a Seat Pad (#29) onto the Right Seat Support (#49). Secure it with two M8 x 2 1/8”

Allen Bolts (#25) and ∅ 5/8” Washers (#24).
B.) Attach a Backrest Board (#28) to the Right Vertical Beam (#21). Secure it with two M8 x 2 1/8”

Allen Bolts (#25) and ∅ 5/8” Washers (#24).
C.) Insert two Foam Roll Tubes (#36) halfway through the holes on the Right Seat Support (#49)

and Leg Developer (#40). Push four Foam Rolls (#33) onto the Tubes from both sides. Plug

four ∅ 1” Round End Caps (#32) into the ends.
D.) Attach the Arm Curl Pad (#34) to the Arm Curl Stand (#35). Secure it with two M8 x 5/8” Allen

Bolts (#31) and ∅ 5/8” Washers (#24). Insert the Arm Curl Stand into the opening in front of

the seat. Use the Lock Knob (#47) on the Right Seat Support to obtain the desired position.
E.) Connect the Lat Bar (#2) to the Upper Cable with a C-clip (#4) and a Chain (#3).
F.) Connect the Arm Curl Handle (#44) to the Front Press Cable (#94) with a C-clip (#4) and a

Chain (#3).

DIAGRAM 12

21

STEP 13 (See Diagram 13)

A.) Securely tighten all the nuts and bolts previously installed.
B.) Before putting the Weight Plates on, now move the machine to the corner of the room or

place where you will use the machine.
C.) Lift up the Selector Rod and install one stack of 19 Weight Plates (#66). To install the plates,

hold the plate at an angle and place between the two Guide Rods then drop it down. Make

sure the grooves on the plastic covers all face up. All the Plates should interlock with each

other. See diagram below. It is strongly recommended to spray some lubricant such as WD-

40 on the two Guide Rods to minimize friction. Use the Selector Pin (#55) to select the desired

weights. The Magnet on the Pin should face up. Repeat the same procedure to install

another stack of Weight Plates.
D.) Attach four Weight Stack Covers (#23) to the machine and secure each Weight Stack Cover

with two M10 x 1” Allen Bolts (#56) and ∅ 3/4” Washers (#6).

DIAGRAM 13

22

PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Lat Bar Grip 2
2 Lat Bar 1
3 Chain 4
4 C-clip 6
5 M10 Aircraft Nut 52
6 ∅ ¾” Washer 82
7 Bracket 3
8 Upper Frame 1
9 1 ¾” Square End Cap 17
10 M10 x 2 ½” Allen Bolt 8
11 Pulley Bushing 10
12 M6 x 1 5/8” Hex Bolt 2
13 ∅1 3/8” Lock Ring 2
14 M6 Aircraft Nut 2
15 Butterfly Axle Sleeve 2
16 ∅ 1 ½” W asher 2
17 M10 x 2 ¾” Carriage Bolt 16
18 Butterfly Support Frame 1
19 2” Square End Cap 2
20 Left Butterfly 1
21 Right Vertical Beam 1
22 Guide Rod 4
23 Weig ht Stack Cover 4
24 ∅ 5/8” Washer 11
25 M8 x 2 1/8” Allen Bolt 8
26 Right Butterfly 1
27 Butterfly Foam Roll 2
28 Backrest Board 2
29 Seat Pad 2
30 2” Sleeve 1
31 M8 x 5/8” Allen Bolt 2
32 ∅ 1” Round End Cap 4
33 Foam Roll 4
34 Arm Curl Pad 1
35 Arm Curl Stand 1
36 Foam Roll Tube 2
37 M10 x ¾” Allen Bolt 2
38 ∅ 1 5/8” Rubber Bumper 2
39 M6 x 5/8” Philips Screw 2
40 Leg Developer 1
41 Leg Developer Axle 1
42 Arm Curl Handle 1
43 Arm Handle Sleeve 2
44 Arm Curl Handle tube 1
45 Handle Grip 4
46 Right Base Frame 1
47 Lock Knob 1
48 1” Square End Cap 4
49 Right Seat Support 1
50 Rear Vertical Beam 1

51 Angled Double Floating Bracket 1
52 M5 Screw 2
53 Magnet Box 2
54 Magnet 2
55 Selector Pin 2
56 M10 x 1” Allen Bolt 22
57 M12 Aircraft Nut 3
58 ∅ 2 ½” Rubber Bumper 4
59 Flat Double Floating Pulley Bracket 1
60 9 ¼” Front Press Axle 1
61 ∅ 7/8” Metal Bushing 14
62 M10 x 8 ¼” Allen Bolt 1
63 Front Press Frame 2
64 M10 x 3” Carriage Bolt 4
65 Weig ht Plate Cover 76
66 Weight Plate 38
67 Selector Stem 2
68 Selector Stem Bushing 4
69 Selector Rod 2
70 M12 x 4 ½” Allen Bolt 2
71 ∅7/8” Washer 6
72 Swivel Pulley Bracket 2
73 1 ½” Square End Cap 3
74 Butterfly Pulley Support 1
75 L-shaped Pin 1
76 Leg Press Plate 1
77 Left Vertical Beam 1
78 Vertical Press Frame 1
79 Pulley 25
80 2” x 1” End Cap 2
81 M10 x 4 7/8” Vertical Press Axle 1
82 M10 x 5 ¾” Allen Bolt 2
83 ∅ 1 ½” Rubber Bumper 1
84 Leg Press Frame 1
85 U-shaped Pulley Bracket 7
86 L-shaped Pulley Bracket 2
87 Left Base Frame 1
88 ∅ 7/8” x ∅ 5/8” Leg Press Bushing 2
89 M12 x 3” Allen Bolt 1
90 Leg Press Diagonal Support 2
91 Vertical Press Grip 2
92 Left Seat Support 1
93 108” Upper Cable 1
94 247” Front Press Cable 1
95 83” Butterfly Cable 1
96 82” Leg Press Cable 1
97 Front Press Base 1
98 M10 x 2” Allen Bolt 17
99 M6 x 5/8” Philips Screw 1
100 M10 x 2 ½” Carriage Bolt 2
101 Ankle Strap 1
102 298” Vertical Press Cable 1

23

WEIGHT RESISTANCE CHART

Station 1 2 3 4 5 6 7 8 9 Low Pulley 40 54 68 80 93 105 116 127 138 Lat Pull 40 55 70 80 90 100 110 120 130 Butterfly 50 55 60 67 74 80 93 106 120 Leg Press 80 107 135 160 185 210 232 254 275 Front Press 54 80 107 116 125 135 162 189 215 Vertical Press 45 60 76 92 113 129 146 172 198

WEIGHT PLATE

WEIGHT PLATE
Station 10 11 12 13 14 15 16 17 18 19
Low Pulley 150 162 174 186 198 210 222 234 246 258
Lat Pull 140 150 160 170 180 190 200 210 220 230
Butterfly 133 146 159 172 185 198 211 224 237 250
Leg Press 297 319 341 363 385 407 429 451 473 495
Front Press 241 267 293 319 345 371 397 423 449 475
Vertical Press 218 238 258 278 298 318 338 358 378 398

*Numbers are approximate. Actual weight may vary.

*Numbers are approximate. Actual weight may vary.

*Numbers are approximate. Actual weight may vary.*Numbers are approximate. Actual weight may vary.

*Val

*Value for butterfly is for each arm.

*Val*Val

ue for butterfly is for each arm.

ue for butterfly is for each arm.ue for butterfly is for each arm.

24

IMPEX INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX") warrants this pr oduct to be f ree fr om def ects in workm ans hip and m aterial,
under normal use and service c onditions , f or a per iod of two years on the Fr ame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or f or products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or cons equential damages aris ing out of or
in connection with the use or performance of the pr oduct or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, cos ts of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of inc idental or consequential damages. Accordingly, the above
limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is lim ited in its sc ope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state
to state.

IMPEX INC.

14777 Don Julian

City of Industry, CA 91746

ORDERING REPLACEMENT PARTS
Replacement parts can be order ed by calling our Custom er Ser vice Department toll-free at 1-800-

999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific

standard time.

www.impex-fitness.com
[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

3. Part Number

4. Date of Purchase

25