Impex CB-430 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Warranty

Ordering Parts

COMPETITOR BENCH

CB-430

Model

CB-430

Retain This

Manual for

Reference

07-03-03

OWNER'S
MANUAL

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................…. 1

IMPORTANT SAFETY NOTICES..................................................................…. 2

HARDWARE IDENTIFIER.....…....................................................................…. 3

ASSEMBLY INSTRUCTIONS........................................................................…. 4

EXPLODED DIAGRAM………………………………………………………………. 10

PARTS LIST...............................................................................................……. 11

WARRANTY.................................................................................................…. 12

ORDERING PARTS.......................................................................................… 12

BEFORE YOU BEGIN

Thank you for selecting the COMPETITOR CB-430 Bench by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed
to provide you complete customer satisfaction. If you have any questions, or
find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service number.
Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:

1. Keep children and pets away from the machine at all times. DO NOT leave

children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine near water
or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes are
also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or physician in
attendance.

10. Before using the machine to exercise, always do stretching exercises to properly warm
up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

HARDWARE IDENTIFIER

3

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.

STEP 1 (See Diagram 1)

A.) Attach the Front Stabilizer (#22) to the Main Frame (#4). Secure it with two M10 x 3

1/8” Carriage Bolts (#54), one 4 ¾” x 1 5/8” Bracket (#26), two ∅ ¾” Washers (#64),
and two M10 Aircraft Nuts (#63).

B.) Connect the two Rear Stabilizers (#5) with the Lat Bar Base (#6). Attach the Main

Frame (#4) to the Lat Bar Base. Secure them together with two M10 x 3 3/8” Carriage
Bolts (#52), ∅ ¾” Washers (#64), and M10 Aircraft Nuts (#63).

Diagram 1

4

STEP 2 (See Diagram 2)

A.) Slide the Sliding Weight Post (#11) onto the Lat Bar Frame (#1). Insert the Lat Bar

Frame into the opening on the Lat Bar Base (#6).

B.) Attach the Cross Brace (#7) to the Lat Bar Base. Align the holes on the Lat Bar Frame,

Lat Bar Base, and Cross Brace. Secure them with three M10 x 2 ¾” Carriage Bolts
(#56), one 1 5/8” x 2” Bracket (#38), one 6 ¾” x 2” Bracket (#39), three ∅ ¾” Washers

(#64), and three M10 Aircraft Nuts (#63). Do not tighten the nuts and bolts yet.
C.) Place the Backrest Adjustment Bar (#10) onto the holders on the Cross Brace.
D.) Attach two Spring Clips (#34) onto the weight posts on the Sliding Weight Post (#11).
E.) Insert one M10 x 2 3/8” Allen Bolt (#67) through the hole on the Lat Bar Frame. Secure

it with two Ø ¾” Washers (#64) and one M10 Aircraft Nut (#63).

DIAGRAM 2

5

STEP 3 (See Diagram 3)

A.) Attach the bottom of Righ t Upright Beam (#3) to the Rear Stabilizer (#5). Attach the Right

Upright Beam to the Cross Brace (#7).

B.) Secure the Right Upright Bea m to the Rear Stabilizer with two M10 x 3 1/8” Carriage Bolts

(#54), ∅ ¾” Washers (#64), and M10 Aircraft Nuts (#63).

C.) Secure the Right Upright Beam to the Cross Brace with two M10 x 2 ¾” Carriage Bolts

(#56), one 4 ¾” x 2” Bracket (#27), two ∅ ¾” Washers (#64), and two M10 Aircraft Nuts

(#63).
D.) Repeat Steps A, B, and C above to install the Left Upright Beam (#2).
E.) Insert the Left & Right Bar Holders (#23 & 24) into the selected holes on the Upright Beam.

DIAGRAM 3

6

STEP 4 (See Diagram 4)

A.) Attach the Cable (#17) to the opening on the top of the Lat Bar Frame (#1). Make sure the ball

stopper of the Cable is underneath the Frame.

B.) Attach a Pulley (#29) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#57), two Ø 5/8”

Pulley Bushings (#43), two ∅ ¾” Washers (#64), and one M10 Aircraft Nut (#63).

C.) Draw the Cable to the bracket on the top of Lat Bar Frame. Attach a Pulley to the bracket. Secure

it with one M10 x 2” Allen Bolt (#55), one L-shaped Pulley Bracket (#28), two ∅ ¾” Washers
(#64), and one M10 Aircraft Nut (#63).

D.) Pull the Cable down to the Sliding Weight Post (#11). Secure the Cable to the Post with one M10

x 1 3/8” Allen Bolt (#53), two ∅ ¾” Washers (#64), and one M10 Aircraft Nut (#63).

E.) Connect a Chain (#37) to the Lat Bar (#12) with a C-clip (#36). Connect the Chain to the Cable

with another C-clip.

7

STEP 5 (See Diagram 5)

A.) Attach the Seat Support (#15) to the bracket on the Main Frame. Secure it with one M10 x 2

½” Allen Bolt (#57), two ∅ ¾” Washers (#64), and one M10 Aircraft Nut (#63).

B.) Attach the holes on the Backrest Supports (#16) to the pivot on the Seat Support (#15).

Attach the Backrest Board (#19) to the Backrest Supports (#16). Secure it with four M6 x 1
3/8” Hex Bolts (#58) and ∅ ½” Washers (#66).

C.) Place the Seat (#18) onto the Seat Support (#15). Secure it with four M6 x 5/8” Hex Bolts

(#60) and ∅ ½” Washers (#66). Insert a L-shaped Pin (#40) into the hole on the Seat Support
to lock the Seat and Backrest Board in position. Remove the Pin when folding the Backrest
Board forward to allow access to the “Walk-in Squat”.

D.) Attach the Arm Curl Pad (#20) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8” Hex

Bolts (#61) and ∅ 5/8” Washers (#65).

E.) Insert the Arm Curl Stand into the opening on the Main Frame. Secure it with a M10 Lock

Knob (#33).

DIAGRAM 5

8

STEP 6 (See Diagram 6)

A.) Attach the Leg Developer (#8) to the Main Frame. Secure it with M10 x 3” Allen Bolt

(#59), two ∅ ¾” Washers (#64), and one M10 Aircraft Nut (#63).

B.) Insert one Foam Tube (#25) halfway through the hole on the Main Base Frame. Insert

two Foam Tubes halfway through the holes on the Leg Developer.
C.) Push six Foam Rolls (#31) onto the Foam Tubes from both ends.
D.) Attach the Curl Bar Handle Frame (#13) to the Leg Developer. Secure it with a L-

shaped Pin (#40). Remove the Pin and the Curl Bar when doing Leg Developer

exercises.
E.) Attach a Spring Clip (#34) to the weight post on the Leg Developer.

DIAGRAM 6

9

10

PARTS LIST

KEY NO. DESCRIPTION Q’ty

1 Lat Bar Frame 1 46 1” Square End Cap 2 2 Left Upright Beam 1 47 ¾” Square End Cap 1 3 Right Upright Beam 1 48 1 5/8” x 2 3/8” End Cap 4 4 Main Frame 1 49 2” Square End Cap 2 5 Rear Stabilizer 2 50 1 ¾” Square End Ca p 1 6 Lat Bar Base 1 51 1 ½” Square End Cap 3 7 Cross Brace 1 52 M10 x 3 3/8” Carriage Bolt 2 8 Leg Developer 1 53 M10 x 1 3/8” Allen Bolt 1 9 Arm Curl Stand 1 54 M10 x 3 1/8” Carriage Bolt 6 10 Backrest Adjustment Bar 1 55 M10 x 2” Allen Bolt 1 11 Sliding Weight Post 1 56 M10 x 2 ¾” Carriage Bolt 7 12 Lat Bar 1 57 M10 x 2 ½” Allen Bolt 2 13 Curl Bar Handle Frame 1 58 M6 x 1 3/8” Hex Bolt 4 14 Curl Bar Handle 1 59 M10 x 3” Allen Bolt 1 15 Seat Support 1 60 M6 x 5/8” Hex Bolt 4 16 Backrest Support 2 61 M8 x 5/8” Hex Bolt 2 17 Cable 1 62 M5 x 3/8” Philips Screw 6 18 Seat 1 63 M10 Aircraft Nut 21 19 Backrest Board 1 64 ∅ ¾” Washer 27 20 Arm Curl Pad 1 65 ∅ 5/8” Wa sher 2 21 Chrome Panel 2 66 ∅ ½” Washer 8 22 Front Stabilizer 1 67 M10 x 2 3/8” Allen Bo lt 1 23 Left Bar Holder 1 24 Right Bar Holder 1 25 Foam Tube 3 26 4 ¾” x 1 5/8” Bracket 1 27 4 ¾” x 2” Bracket 2 28 L-shaped Pulley Bracket 1 29 Pulley 2 30 2” Sleeve 3 31 Foam Roll 6 32 Grip 4 33 M10 Lock Knob 1 34 Spring Clip 3 35 1 ¾” Sleeve 1 36 C-clip 2 37 Chain 1 38 1 5/8” x 2” Bracket 1 39 6 ¾” x 2” Bracket 1 40 L-shaped Pin 2 41 ∅ 1 3/8” Curl Bar Handle Bushing 2 42 ∅ ½” Bushing 4 43 Ø 5/8” Pulley Bushing 2 44 Rubber Bumper 2 45 ∅ 1” End Cap 14

11

IMPEX INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and m aterial, under normal
use and service conditions, for a per iod of two years on the Frame from the date of purchase. This warranty
extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to r eplacing or r epairing,
at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights for products return to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for pr oducts used f or com mer cial or rental purpos es. No other warranty beyond that specifically
set forth above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or consequential dam ages arising out of or in connection
with the use or performance of the product or other damages with respect to any economic loss, los s of property,
loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential
damages or whatsoever natures. Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a par ticular purpose is lim ited in its scope and dur ation to the terms s et forth herein.
Some states do not allow limitations on how long an im plied warr anty lasts. Ac c or dingly, the above limitation may
not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state to state.

Register on-line www.impex-fi tness.com

14777 Don Julian

City of Industry, CA 91746

ORDERING REPLACEMENT PARTS

Replacement parts can be ordered by calling our Custom er Servic e Department toll-free at 1-800-999-8899 during
our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.

[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

3. Part Number

4. Date of Purchase

IMPEX INC.

12