Impex CB-280 User Manual

NOTE:

Please read all instructions

carefully before using this

product

Table of Contents

Safety Notice

Hardware Identifier

Assembly Instruction

Parts List

Warranty

Ordering Parts

COMPETITOR BENCH

CB-280

Model

CB-280

Retain This

Manual for

Reference

07-1704

OWNER'S
MANUAL

IMPEX FITNESS PRODUCTS

14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746

Tel: [phone] Fax: [phone]

www.impex-fitness.com

[e-mail]

TABLE OF CONTENTS

BEFORE YOU BEGIN...................................................................................…. 1

IMPORTANT SAFETY NOTICES..................................................................…. 2

HARDWARE PACK……….....…....................................................................…. 3

ASSEMBLY INSTRUCTIONS........................................................................…. 4

EXPLODED DIAGRAM………………………………………………………………. 10

PARTS LIST...............................................................................................……. 11

WARRANTY.................................…..............................................................…. 12

ORDERING PARTS.......................…..............................................................… 12

BEFORE YOU BEGIN

Thank you for selecting the COMPETITOR CB-280 Weight Bench by IMPEX
FITNESS PRODUCTS. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed
to provide you complete customer satisfaction. If you have any questions, or
find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service number.
Our Customer Service Agents will provide immediate assistance to you.

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

[e-mail]

1

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:

1. Keep children and pets away from the machine at all times. DO NOT leave

children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine near water
or outdoors.

5. Keep hands and feet away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes are
also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or physician in
attendance.

10. Before using the machine to exercise, always do stretching exercises to properly warm
up.

11. Never operate the machine if the machine is not functioning properly.

12. A spotter is recommended during exercise.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

2

HARDWARE PACK

3

ASSEMBLY INSTRUCTION

Tools Required Assembling the Machine: Two Adjustable Wrenches
NOTE: It is strongly recommended two or more people assembling this machine to
avoid possible injury.

STEP 1 (See Diagram 1)

A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#2) in the Mid-span.

Secure them with two M8 x 2 ½” Carriage Bolts (#20), one Bracket (#10), two ∅ 5/8”
Washers (#26), and two M8 Aircraft Nuts (#24) on each end of the Cross Brace.

B.) Insert the Backrest Adjustment Bar (#11) through a selected hole to obtain desired

incline of Backrest.

DIAGRAM 1

4

STEP 2 (See Diagram 2)

A.) Attach the Main Seat Support (#3) to the Cross Brace (#2). Secure it with four M8 x 2

3/8” Hex Bolts (#18), one Bracket (#10), four Ø 5/8” Washers (#26), and four M8
Aircraft Nuts (#24). DO NOT tighten the Nuts and Bolts yet.

B.) Attach the Front Support (#5) to the Main Seat Support (#3). Secure the first hole to

the Main Seat Support with one M8 x 1 5/8” Carriage Bolt (#28), one Ø 5/8” Washer
(#26), and one M8 Aircraft Nut (#24). DO NOT tighten the Nut and Bolt yet.

C.) Attach one end of the Diagonal Support (#4) to the second hole on the Main Seat

Support. Align the holes and secure them together with one M8 x 1 ¾” Carriage Bolt
(#29), one Ø 5/8” Washer (#26), and one M8 Aircraft Nut (#24). Attach the other end
of the Diagonal Support to the Front Support (#5). Secure it with one M8 x ½” Hex Bolt
(#30) and Ø 5/8” Washer (#26).

D.) Securely tighten all Nuts and Bolts previously installed.

DIAGRAM 2

5

STEP 3 (See Diagram 3)

A.) Attach the Leg Developer (#6) to the Front Support (#5). Secure it with one M10 x 2

3/8” Hex Bolt (#21), two Ø ¾” Washers (#31), and one M10 Aircraft Nut (#27). Do not
over tighten the Bolt. Make sure the Leg Developer is able to swivel.

B.) Insert two Foam Tubes (#13) halfway through the holes on the Leg Developer. Push

four Foam Rolls (#12) onto the Tubes from both sides.

C.) Place a Spring Clip (#39) onto the weight post on the Leg Developer.

DIAGRAM 3

6

STEP 4 (See Diagram 4)

A.) Attach the hole-side of the Backrest Supports (#7) onto both ends of the pivot on the Main

Seat Support (#3). Place the other end rest against the Backrest Adjustment Bar (#11).

B.) Place the Backrest Board (#8) onto the Backrest Supports. Secure it with four M6 x 1 5/8”

Hex Bolts (#23) and Ø ½” Washers (#25).

C.) Place the Seat Pad (#9) onto the Main Seat Support. Secure it with four M6 x 5/8” Hex

Bolts (#22) and Ø ½” Washers (#25).

DIAGRAM 4

7

STEP 5 (See Diagram 5)

A.) Attach the Arm Curl Pad (#34) to the Arm Curl Stand (#42). Secure it with

two M8 x ¾” Hex Bolts (#33) and Ø 5/8” Washers (#26).

B.) Insert the Arm Curl Stand into the top opening on the Front Support and

secure it with a Lock Knob (#32).

DIAGRAM 5

8

STEP 6 (See Diagram 6)

A.) Slide the 25lb (#36), 15lb (#37), and 10lb (#38) Weight Plates onto the Weight Bar

(#35). Note: Plates must be installed in pairs, one on each side.

B.) Attach two Spring Clips (#39) onto the Weight Bar.

DIAGRAM 6

9

10

PARTS LIST

KEY NO. DESCRIPTION QUANTITY

1 Rear Upright Beam 2
2 Cross Brace 1
3 Main Seat Support 1
4 Diagonal Support 1
5 Front Support 1
6 Leg Developer 1
7 Backrest Support 2
8 Backrest Board 1
9 Seat 1
10 Bracket 3
11 Backrest Adjustment Bar 1
12 Foam Roll 4
13 Foam Tube 2
14 Ø ¾” Round End Cap 4
15 Ø 1” Round End Cap 7
16 Rubber Bumper 1
17 1 ½” Square End Cap 2
18 M8 x 2 3/8” Hex Bolt 4
19 1” Square End Cap 4
20 M8 x 2 ½”Hex Bolt 4
21 M10 x 2 3/8” Hex Bolt 1
22 M6 x 5/8” Hex Bolt 4
23 M6 x 1 5/8” Hex Bolt 4
24 M8 Aircraft Nu t 10
25 Ø ½” Washer 8
26 Ø 5/8” Washer 13
27 M10 Aircraft Nut 1
28 M8 x 1 5/8” Carriage Bolt 1
29 M8 x 1 ¾” Carriage Bolt 1
30 M8 x ½” Hex Bolt 1
31 Ø ¾” Washer 2
32 Lock Knob 1
33 M8 x ¾” Hex Bolt 2
34 Arm Curl Pad 1
35 48” Weight Bar 1
36 25lb Weight Plate 2
37 15lb Weight Plate 2
38 10lb Weight Plate 2
39 Spring Clip 5
40 Sliding Sleeve 1
41 48” Curl Bar 1
42 Arm Curl Stand 1

11

IMPEX INC.

LIMITED WARRANTY

IMPEX Inc. ("IMPEX") warrants this produc t to be free from defects in workm anship and m aterial, under
normal use and service conditions, f or a period of two years on the Frame from the date of pur chase.
This warranty extends only to the original purchaser. IMPEX's obligation under this W arranty is lim ited
to replacing or repairing, at IMPEX's option.

All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights for products return to IMPEX must be
prepaid by the customer. This warranty does not extend to any product or dam age to a produc t caused
by or attributable to freight damage, abuse, misuse, improper or abnorma l usage or repairs not provided
by an IMPEX authorized service center or for products used f o r c ommercial or rental pur pos es. No other
warranty beyond that specifically set forth above is authorized by IMPEX.

IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or perform ance of the product or other damages with respec t to any economic
loss, loss of property, loss of revenues or profits, loss of enjoyments or use, c osts of rem oval, ins tallation
or other consequential damages or whatsoever natures. Some states do not allow the exclusion or
limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpos e is limited in its scope and duration to the terms set forth
herein. Some states do not allow lim itations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.

This warranty gives you specific legal right. You may also have other rights which vary from state to

Register on-line www.impex-fi tness.com

state.

IMPEX INC.

14777 Don Julian

City of Industry, CA 91746

ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Departm ent toll-free at 1-800-999-

8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.

[e-mail]

When ordering replacement parts, always give the following information.

1. Model

2. Description of Parts

3. Part Number

4. Date of Purchase

12