Imperial 1936ENVSS Installation Manual

1900E & 1900ENV

Installation Instructions

&

Warranty Information

ECON/10.18

425 Apollo Street

Brea, CA 92821

www.imperialhoods.com

[phone]

DO NOT THROW AWAY,

PROPERTY OF THE HOME OWNER!

Imperial Cal Products, Inc.

Any cosmetic defects must be reported to us prior to installation.
Once this hood is installed, ICP will NOT accept any responsibility

for any cosmetic blemishes, scratches or dents in the Canopy.

Save all original packaging if you wish to return for any reason!

FIRST:

Check your local building and electrical codes.

WARNING:

To reduce the risk of fire or electrical shock, Do Not use any two speed motor units with a Solid
State control devise.

CAUTION:

To reduce the risk of fire or personal injury and to properly exhaust air, be sure to duct air to the
outside. DO NOT vent exhaust air into spaces within wall, attics, ceilings, crawl spaces or
garages. When venting to the outside make duct run as short and straight as possible.
Avoid using elbows if at all possible as this will reduce your performance. Every elbow will
decrease the performance and we will not guarantee the effectiveness of the range hood.

No Performance Warranty when used above BBQ Style Grills.

DO NOT use duct pipe smaller than the outlet duct opening on the hood, this will reduce
performance and void the warranty. DO NOT use flex ducting. Also, use either a Roof Cap or
Wall Cap to end run. Be sure that all joints are taped securely in place. It is essential to have the
proper distance between the bottom of the range hood and the cooking surface below. In most
cases the cooking appliance manufacturers specifications will establish the fire safe minimum
distance required, although there are other factors to consider:

 Local Building Codes
 Cross directional air movements ie: open windows, air conditioning/heating outlets, cooling

fans, etc.

 Overall size of the cooking appliance and surrounding countertop surfaces.
 Range hood model selected.

For best performance distance between cooking surface and the bottom of the hood is 30” and
36”. Check local codes and appliance specifications. Keep in mind, increasing the distance will
decrease the performance.

DISCLAIMER

Imperial assumes no liability regarding the improper installation or misapplication of its products. It
is the installer’s responsibility to check for proper installation. Under no circumstances will Imperial
be liable for any labor charged or travel time incurred installation of its products. Damage caused
by improper installation is the installers responsibility and Imperial assumes no liability.

Read Before Starting Installation!

Inspect your range hood prior to installing!

WARNING: This product can expose you to certain chemicals, which are known to the State of California to cause
cancer or birth defects or other reproductive harm. For more information to go: www.P65WARNINGS.ca.gov.

Economy Series Installation Details:

MODELS

1900E, 1900ENV

CABINET: Be sure that the cabinet bottom is level, side to side and front to rear.
For the Vented Unit (1900E) you will need to cut an 8” x 8” hole in the bottom of the cabi­net, 3/4” in from the rear wall and on center line. For the Non-Vented model (1900ENV)
there is no need for a duct pipe cut out. Shelves and top to be cut to clear 7” round pipe to
line up with the bottom cabinet cut out. Also, cut holes for electrical wires for both Vented
and Non-Vented.

ELECTRICAL: Bring enough wire into cabinet to reach in front of vent pipe. Enter cabinet
3 1/4” left of center and 1 1/2” from wall for vented and non-vented units. Remove
electrical box cover before mounting hood. Units are to be hard wired

recommended to add a power-cord. Adding a power cord can loosen existing wires
inside junction box causing electrical failure.

NOTE: Be sure to remove black electrical tape that holds the damper blades closed.

MOUNTING: Insert canopy below the cabinet, being sure your vent opening and electrical

cut outs line up with cabinet cut outs. Use the Key Hole mounting holes to secure the
canopy. After hood is mounted attach house wires to leads in the hood. Secure locknut to
conduit and check wiring for compliance to local building codes.

FINISH: Replace electrical box cover. Connect duct and tape all joints. Install 40 Watt bulb
and replace Filter. (bulbs not included)

WARNING:

To reduce the risk of fire or electrical shock DO NOT use the “E” series with any solid-state
speed control device.

. It is not

1900E

1900ENV

Imperial Cal Products, Inc.

To order replace parts or schedule service please call our office at [phone] or use our
website… www.imperialhoods.com.

PARTS:

When ordering Parts we need the following information:

 Model Number (not serial number) found on UL label inside hood.
 Exact dimensions (in the case of filters)

You can find the model number on the inside of your hood on our UL label. There will be a
several model numbers listed, your model number should have some kind of mark next to it
to indicate the exact model you have.

In the case of Filters we will need the exact dimensions of the filter needed. Indicate which
side has the pull tabs on it. Filters are not a warranty replacement part. With care your filters
should last many years.

Payment on Parts is handled one of three ways: PrePaid (you send a check prior to our Ship­ping), call with credit card information, VISA or MasterCard, COD or Cash if you decide to
“Will Call”.

Our Will Call hours are 8:30 to 3:30, Monday through Friday.

SERVICE:

When calling in for Service we need the following information:

 Model Number (not serial number)
 Proof of Purchase
 Name of company you purchased the hood through.
 Name & Phone number of the person to contact to set up the service call.
 Full address of the location where service is to be done.

1 Year Parts Only

Maintenance & Warranty Information

This product has the simplest of cleaning requirements. Clean filters often for the best
performance. How often depends on amount and type of cooking. Use hot water and a
degreaser. When cleaning a painted hood, wash it with mild, soapy water ONLY! Wipe the
hood thoroughly with clean water and dry with soft cloth. When cleaning Stainless Steel use a
cleaner specifically for Stainless Steel. Always rub with the grain using non-abrasive cleaning
materials. AVOID detergents, disinfectants or cleaning products in aerosol cans. NEVER use
abrasive scouring powders on your hood! Some cleaning chemicals may damage the hood
finish!

 Economy Models 40 Watt Incandescent OR 6 Watt LED.
***Bulbs not included on any model.***

Warning: Do not use any bulbs that are not instructed by manufacturer.

MUST show proof of original purchase date is needed to obtain service under warranty.

1900D, 1900E or 1900ENV: One Year Limited Warranty on Parts Only.

NOTE:

Service companies will perform Warranty Service, Monday through Friday from 7 a.m.—4:
p.m. The service company will call and schedule a date and time with a 4 hour window. If the
service company arrives at your location, during the scheduled date and time, and no one is
home, you will be charged a trip charge by the service company for a return service call.

1900E or 1900ENV we will provide parts only for 1 year from date of original purchase.
Call for service or parts at [phone]

1. Service calls to correct the installation of your appliance, to instruct you how to use your
appliance, to replace or repair house fuses or the correct housing wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs or filters.

3. Repairs when your appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God,
improper installation, installation not in accordance with electrical or plumbing codes.

5. Replacement parts or repair costs for units operated outside the United States.

6. Pickup and delivery. This appliance is designed to be repaired in the home.

7. Repairs to parts or systems resulting from unauthorized modification made to the
appliance.

8. Expenses for travel and transportation for product service in remote locations.

9. The removal and reinstallation of your appliance if it is installed in an inaccessible location
or is not installed in accordance the published installation instructions.

10. Replacement parts or repair labor costs when the appliance is used in a country other
than the country in which it was purchased.

Your Imperial Warranty:

ITEMS IMPERIAL WILL NOT

PAY FOR