One Year Limited Warranty (US) .................................................................................................. 8
ii
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed
including the following:
1. Read all instructions.
2. To protect against risk of electrical shock do not put appliance, cord or plug in
water or other liquid.
3. Close supervision is necessary when any appliance is used by or near children.
4. Unplug from outlet when not in use, before putting on or taking o parts, and
before cleaning.
5. Avoid contacting moving parts.
6. Do not operate any appliance with a damaged cord or plug or aer the appliance
malfunctions, or is dropped or damaged in any manner. Return appliance to
the nearest authorized service facility for examination, repair or electrical or
mechanical adjustment.
7. The use of attachments, including cups, not recommended by the manufacturer
may cause re, electric shock or a risk of injury.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner or in a heated oven.
11. Blades are sharp. Handle carefully.
12. To reduce the risk of injury, never place cutting blade on base without rst
putting bowl properly in place.
13. Do not attempt to defeat the cover interlock mechanism.
14. Do not use appliance for other than intended use.
ENGLISH
ESPAÑOL
FRANÇAIS
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY
POLARIZED PLUG
This appliance has a polarized plug (one blade is wider than the other). To reduce the
risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not modify the plug in any way.
3
ENGLISH
WHAT’S IN THE BOX
ESPAÑOL
FRANÇAIS
TOP VIEW
BOTTOM VIEW
4
GETTING STARTED
Prior to using your coffee mill for the first time, you should wipe the hopper with a
damp cloth. Place the coffee mill on a level surface and on your kitchen counter, and
plug into an AC outlet with the correct voltage.
Since the coffee mill is not designed to be used with previously ground coffee, you
should have already purchased coffee beans, and you should have them ready. To
keep the beans fresh, you should pour them into an airtight container after they are
brought home.
The coffee mill is not designed to hold more than 1 ounce of beans, so using a kitchen
scale, weigh out the proper amount, and then put the beans into a utensil for the
purpose. Take note of the amount in terms of volume; you will typically be weighing
out just over 1/8 of a cup, and there are 2 ounce cups that are sold in the store that
can be used in the future for this purpose. You can also use 3 ounce cups, provided
that you do not fill them to the top.
USING THE COFFEE MILL
• Remove the mill cover.
• Pour the desired quantity of coee beans into the mill well, being careful not to
exceed 1 ounce, or more specically, 26 grams.
ENGLISH
ESPAÑOL
FRANÇAIS
• Place the cover back on the mill. Note: the mill will not work without its cover
and/or if it is not seated properly.
• To start the mill, press the on/o button at 5-10 second intervals, until you have
obtained the desired level of neness. For coarse grinds, grind between 5 and 10
seconds; for ne grinds, 10 to 15 seconds.
• Aer grinding, wait until the blades stop before removing the cover.
• Remove the cover to pour out the ground coee into your coee machine
basket.
• Note that there will be some residual ground coee remaining in the coee
well. If you are using the coee mill daily, you can leave that ground coee
there under its airtight cover. However, if you are not going to be using the mill
for a long period of time, and you want to clean the mill before the next use,
disconnect the mill from the outlet, and then, using a damp cloth or paper
towel, wipe the well.
• Aer usage, if you don’t want the mill to remain on the counter, unplug the
device and re-wind the cord into the cord collector.
5
ENGLISH
CARE & CLEANING
IMPORTANT: DISCONNECT THE MILL’S POWER SUPPLY BY UNPLUGGING IT BEFORE
CLEANING.
ESPAÑOL
• To clean the well, use a damp, clean so cloth or paper towel.
• Do not use abrasive products, as these are prone to scratching and removing
the sheen.
Before contacting customer support, please see the troubleshooting guide above/
below.
Visit our website to contact us, nd answers to Frequently Asked Questions, and for
other resources which may include an updated version of this user’s guide.
WWW.COURANTUSA.COM
If you wish to contact us by phone, please be sure to have your model number and
serial number ready and call us between 9:00am and 6:00pm ET, at +1 888-943-2111.
Keep tabs on Courant’s newest innovations & enter contests via our social network
feeds:
1. First, ensure that the cover has been correctly seated. If it is not been, the mill
will not operate. If you have determined that the cover has been correctly
seated, go to the next step.
2. The electrical power may have been shut o to that wall outlet. In some cases,
this could be due to a circuit breaker or fuse being disabled, or, in other cases,
there are wall switches that control power to outlets that could have been
moved by mistake. To see if power is going to be wall outlet, you can plug
another appliance into the outlet, or, alternatively, you could plug the mill into a
dierent outlet that you know is functioning. If the power is going to the outlet,
go to the next step.
3. Unplug the unit, then check the cable to make sure that it is not been severed
and that is still correctly attached to the mill. If the cable is ne, go to the next
step.
4. Contact Courant Technical Support.
THE MILL IS OPERATING NORMALLY, BUT STOPS ABRUPTLY:
1. Immediately turn o the mill. A foreign object, such as a pebble, green unroasted
coee bean, or even a twig, may have jammed the blades.
2. Unplug the mill from the outlet.
3. Remove the cover, and try to dislodge any found objects. If you are successful,
plug the mill back into the outlet, and resume writing your coee.
ENGLISH
ESPAÑOL
FRANÇAIS
THE GRIND IS NOT FINE ENOUGH OR COARSE ENOUGH:
1. Adjust the amount of time for the grinding process.
THE MILL IS ABNORMALLY LOUD OR MAKES STRANGE SOUNDS WHEN
GRINDING:
1. In normal operation, the process of running a motor and grinding coee is
inherently loud. However, if the mill is louder than normal or makes strange
sounds, stop grinding, remove the mill from the wall outlet, remove the cover,
and check to see if foreign objects are being ground.
7
Loading...
+ 15 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.