Impact Quikbox™Softbox
INSTRUCTIONS
Introduction
Congratulations on your purchase of the Impact Quikbox™Softbox. This
revolutionary pop-up softbox was designed to be portable and simple to set
up, giving photographers a quality flash diffuser at an affordable price.
Softbox Features
· Easy Assembly: Unique pop-up design makes assembly process quick
and easy
· Eliminates Difficulty: Lack of external flex rods eliminate complex
installation process
· Instantly Transportable: Compact design makes transport and storage
easier than ever
· Remarkably Adaptable: Mounts onto strobes using universal speed
ring inserts
· Multi-Purpose Use: Lightweight design allows for indoor and outdoor
usage all year round
The Impact Quikbox Softbox is for use with strobes only. It should not be
used with hot lights. Please read these instructions carefully on how to
assemble and break down your new softbox.
2
Setting up the Softbox
The Impact Quikbox Softbox consists of a pre-built, internal rod softbox that
allows for rapid assembly. To assemble your Quikbox Softbox, follow these
instructions:
1. Remove softbox shell from
carry bag and begin unfolding
by pulling panels outward like
a book
2. Rotate softbox so that
larger opening faces toward
you; then spread apart the
opposing panels until softbox
shell pops open into a squareshaped box.
3
Installing the Diffusers
1. Install inner diffuser by
fastening metal clips found
on smaller diffuser cloth to
elastic loops found on each
corner of softbox interior
4
2. Install outer diffuser by
attaching white fastener strip
found on bigger diffuser cloth
to black fastener strip found
on softbox interior
Inserting the Speed Ring
The elastic rim located in the back of the softbox will accommodate a
universal (~145 mm) speed ring insert (sold separately). To mount a speed
ring insert, follow these instructions:
1. Gently wedge the wide end
of the insert under the elastic
rims located in the back of the
softbox.
Note: For instructions on how to mount your Impact Quikbox to your strobe,
refer to your strobe’s instruction manual.
2. Mount the Impact Quikbox
Softbox onto your strobe light.
5
Breaking Down The Quikbox Softbox
1. Remove the entire Quikbox
and speed ring assembly from
your strobe. Note that the
speed ring may be hot to the
touch due to the heat of the
strobe or modeling light. In
that case, wait for it to cool
before proceeding to the next
step.
6
2. Carefully lift speed ring
bracket away from elastic
rims located in the back of the
softbox.
Breaking Down The Quikbox Softbox
3. If desired, the softbox
shell may be stored with
both diffusers still in place;
otherwise, remove the
diffuser fabrics entirely and
place them inside the carrying
case.
4. Snap the opposing corners of
the softbox panels together,
then fold the remaining two
panels together as if closing a
book, and stow the collapsed
softbox shell inside the
carrying case.
7
One-Year Limited Warranty
This IMPACT product is warranted to the original purchaser to be free from
defects in materials and workmanship under normal consumer use for a period of
one (1) year from the original purchase date or thirty (30) days after replacement,
whichever occurs later. The warranty provider’s responsibility with respect
to this limited warranty shall be limited solely to repair or replacement, at the
provider’s discretion, of any product that fails during normal use of this product in
its intended manner and in its intended environment. Inoperability of the product
or part(s) shall be determined by the warranty provider. If the product has been
discontinued, the warranty provider reserves the right to replace it with a model
of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect,
accident, alteration, abuse, improper installation or maintenance. EXCEPT AS
PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS
WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED
TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specic legal rights, and
you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Impact Customer Service Department
to obtain a return merchandise authorization (“RMA”) number, and return the
defective product to Impact along with the RMA number and proof of purchase.
Shipment of the defective product is at the purchaser’s own risk and expense.
For more information or to arrange service, visit www.impactstudiolighting.com
or call Customer Service at 212-594-2353.
Product warranty provided by the Gradus Group.
www.gradusgroup.com
IMPACT is a registered trademark of the Gradus Group.
© 2014 Gradus Group LLC. All Rights Reserved.
GG2
Loading...