Impact OCTACOOL-6, OCTACOOL-9, OC6-CASE-KIT, OC9-CASE-KIT User manual

OctaCool Fluorescent Light
INSTRUCTIONS
Congratulations on your purchase of the Impact OctaCool Fluorescent Light Kit. Enjoy the many benets of a continuous uorescent light, such as less power used than typical ash units, cooler operation, cheaper replacement lamps, and “what you see is what you get” lighting as there are no surprises as to how the light will fall. Please read these operating instructions and safety precautions before operating this equipment.
• Includes a 29.5˝ OctaCool softbox that provides a soft, uniform, diffused light
• Noiseless operation allows clear audio for video productions
• Cool output allows heat-sensitive subjects to be photographed up close with ease
• 28W screw-in uorescent lamps with a life expectancy of 6000-8000 hours*
What’s Included
• OctaCool 6- or 9-light head
• 6 or 9 28W screw-in uorescent lamps (daylight balanced 5000°-5500°K)
• 29.5˝ (75 cm) OctaCool Softbox
• 8 tension rods
• Internal diffusion bafe
• OctaCool softbox diffuser
• 120V AC power cord
Power Requirements
This light is designed for use with 110/120V AC power only, and is supplied with a 3-prong, grounded plug. Do not attempt to defeat this safety feature. If necessary, use only grounded extension cords rated for 10 amps or greater.
Caution
There are no user-serviceable parts inside the unit. Only qualied service engineers should access the inside of the case (Danger – high voltage parts inside). If any of the lamps become cracked or damaged in any way, they should be replaced immediately. Do not use the light unit in an environment where it is likely to come in contact with moisture or ammable vapors. Turn the power off and unplug the power cord when the unit is not in use. Always remove the lamps when transporting the unit.
*Service life depends upon many conditions. Individual results may vary.
Assembly
The Impact OctaCool Fluorescent Light comes in 6-light and 9-light models. The illustrations in this guide show a 9-light model, but the 6-light model is assembled the same way.
Place the OctaCool light head face up on a at surface.
Place the OctaCool softbox around the light head. It will take shape with the following steps.
Insert the rst tension rod in any of the eight pockets at the outer edge of the OctaCool softbox.
1
2
3
1
Assembly (continued)
Insert the other end of the tension rod into the speedring hole on the side of the light head.
Insert the next rod at the exact op­posite side (180°) of the rst rod that was inserted. Insert one end into the correct pocket on the OctaCool softbox rst, and then insert the other end into the light head.
Insert the next two rods at a 90° an­gle from the rst two rods that were inserted. Follow the same steps as the rst two rods. Insert one end into a pocket on the OctaCool soft­box rst, and then insert the other end into the light head.
4
5
6
2
Insert the remaining rods, always placing one rod, and then the next on the opposite side. Once all rods are placed, the OctaCool softbox will rm up and take shape.
Close the touch-fastener strips on the back of the OctaCool softbox to ensure that it ts tightly. This will prevent any light leaks.
Close the touch-fastener strips on the back of the OctaCool softbox to ensure that it ts tightly. This will prevent any light leaks.
7
8
9
3
Assembly (continued)
Screw in all of the uorescent lamps. Only touch the base of the lamp; never touch the glass itself. The oils on your hand can shorten the life of the bulb.
If desired, attach the internal diffusion bafe to the metal clips hanging on the inside of the OctaCool softbox. For stronger light, you can leave out the internal diffuser.
10
11
4
Stretch the diffuser over the edge of the OctaCool softbox. Make certain that the diffuser ts tightly on all sides.
Mount the light head onto a light stand with a standard 5/8˝ stud and use the four-pronged knob to tighten it.
Use the ratcheting tilt lock handle to adjust the head’s tilt. To adjust the ratchet, pull the handle outward and move to the desired position.
Insert the included power cable to the back of the light head. Plug the other end into a power outlet.
12
Tilt Lock Handle
13
Light Stand
Lock Knob
14
5
Operating Instructions
Each switch on the back panel controls either one or two bulbs. With the OctaCool 9 you can select to have only one bulb on, all bulbs on, or any number of bulbs in between. The OctaCool 6 allows you to select 2, 4 or 6 bulbs. Each compact uorescent bulb may take up to ve minutes to reach its full bright­ness, but will output 1400 lumens. All six bulbs in the OctaCool 6 will give off 8400 lumens. All nine bulbs in the OctaCool 9 will give off 12,600 lumens (both lumen calculations at 3.3 feet).
Refer to the diagrams below for the exact relationship between the switches and the corresponding bulb(s) There are also markings next to the switches that indicate which bulbs are powered by the switch.
A
B C
C B
A
C B
A
OctaCool 6
6
A
B
C
D E
B
OctaCool 9
A
C
D E
A
DE
B
7
Disassembly
Ensure that all of the power controls on the back of the light head are in the OFF position. Unplug the power cord from the wall outlet.
Unplug the power cord from the back of the light head.
Release the light stand locking knob and remove the light head from the light stand.
1
2
3
8
Remove the OctaCool diffuser by pulling it off.
Detach the internal diffusion bafe from the metal clips hanging on the inside of the OctaCool softbox.
Unscrew all of the uorescent lamps. Only touch the base of the lamp; never touch the glass itself. The oils on your hand can shorten the life of the bulb. Never transport your OctaCool light head without rst removing all of the uorescent lamps.
4
5
6
9
Disassembly (continued)
Detach all the touch-fastener strips on the back of the OctaCool softbox.
Remove any single tension rod from the light unit.
Remove the rod from the pocket on the opposite end. Next, remove the rod at the exact opposite side, and repeat the process until all rods are removed.
7
8
9
10
Specications
Input Voltage 110-120V AC; 60Hz; 3.5A draw Lamps 27-32W screw-in uorescent
(daylight balanced 5000°-5500°K) Ballast In lamps Mounting 5/8˝ standard stud Octacool 6 Weight Light head: 2.8 lb. (1.2 kg) Complete Kit: 10.1 lb. (4.6 kg) Octacool 9 Weight Light head: 3.2 lb. (1.45 kg) Complete Kit: 12.5 lb. (5.6 kg) Dimensions Light head: 9˝ (29 cm) diameter OctaCool softbox: 29.5” (75 cm) diameter
11
Safety and Maintenance
Safety Notes
• Turn the power OFF and unplug the power cord when the light is not in use
• Do not use the light in an environment where moisture may come in contact with the unit
• A re hazard exists if ammable materials are placed in close proximity to the lamps
• Do not use your light in an environment where ammable vapors are present
• Do not restrict the ventilation holes when the light is in use
• Always switch OFF the power and disconnect the power cord before removing or replacing any lamp(s)
• Avoid placing cables where they can be tripped over
• Replace damaged cords immediately
• Never use a light head with damaged covers, moldings, or lamps
• If the unit is dropped or damaged, have it checked by a professional repair service before using
• Due to the high-voltage circuitry inside this device, do not attempt to disassemble or repair the unit yourself
• Keep out of the reach of children
Changing the Fuse
A 3.15A 250 V fuse is mounted in the rear panel and protects the circuitry of the light head. Turn off the unit and disconnect the power supply before changing the fuse. Never replace with a fuse of a different type or rating. A spare fuse is tted within the fuse holder. Use a small screwdriver to release the fuse cover. Remove the old fuse, place the new fuse in the slot, then replace the fuse holder.
12
One-Year Limited Warranty
This Impact product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with specic legal rights, and you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Impact Customer Service Department to obtain a return merchandise authorization (“RMA”) number, and return the defective product to Impact along with the RMA number and proof of purchase. Shipment of the defective product is at the purchaser’s own risk and expense.
For more information or to arrange service, visit www.impactstudiolighting.com or call Customer Service at 212-594-2353.
Product warranty is provided by the Gradus Group.
www.gradusgroup.com
Impact is a registered trademark of the Gradus Group. © 2014 Gradus Group LLC. All Rights Reserved.
GG3
To see all of our lighting equipment,
please visit our website.
www.impactstudiolighting.com
Loading...