Impact LSA-BAWMBL User manual

LSA-BAWMBL

Wall-Mounted Boom Arm

INSTRUCTIONS

1

Precautions ⚠⚡

• Do not exceed the maximum load capacity.

• Always engage safety locks and devices where applicable.

• Product should be used between -22°F and 140°F (-30°C and 60°C)
only.

• Please read and follow these instructions, and keep this manual in a
safe place.

• Keep this unit away from water and flammable gases or liquids.

• Do not attempt to disassemble or repair the equipment—doing so will
void the warranty, and Impact will not be responsible for any damage.

• Handle the unit with care.

• Clean the unit with a mild detergent and a soft cloth.

• Keep this unit away from children.

• Use only parts provided by the manufacturer.

• Be certain that the boom arm is securely attached to the wall before
proceeding.

• Make sure the item is intact and that there are no missing parts.

• All photos are for illustrative purposes only.

2

Introduction

Thank you for purchasing the Impact LSA-BAWMBL Wall-Mounted Boom
Arm. When this boom arm is securely mounted to a wall, you have a quick
and safe way to mount a light or camera without setting up light stands or
taking up valuable floor space. A 5/8˝ socket at the end of the arm holds a
reversible stud with 1/4˝ and 3/8˝ male threads. The boom arm can extend
from 48˝ to 87˝and handle a load of up to 8 lbs. when fully extended. The
arm offers a pan movement of 180° as well as a tilt movement of 180°.

Contents Include

• Telescoping boom arm

• 5/8˝ stud with reversible
1/4˝-20 and 3/8˝ male
threads

• Removable cable clip

Specifications

Boom length minimum 48˝ (123 cm)

Boom length maximum 87˝ (221 cm)

Maximum recommended load at full
extension

Pan movement 180°

Tilt movement 180°

Attachment type two-position 5/8˝ removable stud with

Weight 5.0 lb. (2.3 kg)

• Allen key

• Mounting hardware

• Mounting instructions

• One-Year Limited Warranty

8.0 lb. (3.6 kg)

1/4˝-20 and 3/8˝ male threads

3

Mounting a light to the boom arm

Securely mount the boom arm to the wall. Be certain that the wall will
support the weight of the boom arm plus whatever you plan to mount on
the boom arm.

1. Loosen the locking knob and
remove the mounting stud
from the end of the boom
arm.

4

2. Mount the light to the 1/4˝
or 3/8˝ end of the mounting
stud.

3. With the light mounted,
replace the stud at the end
of the boom arm and hand­tighten the locking knob.

Operating the boom arm

1. To raise or lower the boom
arm, loosen the ratchet
handle and push the boom
arm up or down to the desired
position. Lock the position by
hand-tightening the ratchet
handle.

Note: If tightening the ratchet
handle does not securely lock the
position of the boom arm, you
may use the included Allen key to
tighten the two Allen screws in the
base riser collar. This will lock the
position securely. To change the
position of the boom arm again,
you will have to first loosen the
Allen screws.

5

Operating the boom arm

2. To move the boom arm to the left or right, simply move the hinge on
the base of the boom arm to the desired position.

6

Operating the boom arm

3. To extend the boom arm,
loosen the locking knob and
pull the extension section of
the arm out to the desired
position. With the locking
knob loosened, you can also
rotate the extension section
to position the light at the
desired angle.

Note: In order to prevent
accidents, always keep one hand
on the light when changing the
position of the boom arm. Never
exceed the load capacity of 8 lbs.

7

One-Year Limited Warranty

Impact provides a limited warranty that this product is free from defects in
materials and workmanship to the original purchaser under normal use for a
period of one (1) year from the original purchase date or thirty (30) days after
replacement whichever occurs later. Our responsibility with respect to this
limited warranty shall be limited solely to repair or replacement, at its option,
of any product which fails during normal consumer use.

To obtain warranty coverage during the Warranty Period, contact your place
of purchase (“Seller”) to obtain a return merchandise authorization (“RMA”)
number, and return to Seller the defective product along with proof of
purchase and the RMA number.

This warranty does not extend to damage or failure which results from
misuse, neglect, accident, alteration, abuse, improper installation or
maintenance. EXCEPT AS PROVIDED HEREIN, IMPACT MAKES NEITHER
ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING
BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. This warranty provides you with
specific legal rights, and you may also have additional rights which vary
from state to state.

© Copyright 2013 Gradus Group

8