IMOU A1 User guide [ml]

Quick Start Guide

A1

www.imoulife.com

Welcome

Thank you for choosing IMOU.
We are devoted to providing you easy smart home
products. If you have problems using the product, please
contact our service team before returning your product.

Our service mail: [e-mail]

Detailed installation instructions & videos, frequently asked
questions can be found at: imoulife.com/support/help
Or scan this QR code to help page.

Package content

Camera ×1 Power Cable ×1 Power Adapter ×1 Positioning Map ×1

Quick Start Guide ×1

Camera introduction

LED Indicator

Lens

Built-in Mic

Micro SD
Card Slot

Reset/Pair

Button

Note:

Press and hold the reset button for 10 s to reset the camera.

The pattern of the LED indicator is included in the following table.

LED Status

O

Red light on

Green light ashing
Green light on

Red light ashing

Green and red light
ashing alternately

Device Status
Powered o/LED turned o
Rebooting after reset
Booting
Device malfunction
Waiting for network

Operating properly
Network connection failed

Firmware updating

Built-in Speaker

Ethernet Port

Power Port

Imou Life

Tips

i

To ensure the best possible wireless performance, please make sure there are
no obstacles and electromagnetic interference between the camera and router.

Setup

WIFI Name

Password

Next

Ceiling Mounting (Optional)

Mounting

1

Surface
Positioning
Map
Expansion
Bolt

Mounting
Plate

Self-tapping

2

Screw

3

Camera

Setup

Done

+45

-10

DC

5V2A

Troubleshooting

Problem Solution

Cannot set up camera

The APP says "Failed

to congure device

network"

The app says “
Failed to bind”

No picture / signal

Picture is not clear

No audio

Human detection

not working

Camera stuck

downwards

Phone is not

reading QR code

• Ensure your mobile device and the camera are within range of your
Wi-Fi router.

• Ensure the LED indicator on the camera isashing green before
beginning setup.

• Reset your Camera and connect it again.

• Some cameras only support 2.4GHz, while some routers have dual
band, 2.4G/5G. Make sure you are connecting 2.4GHz only.
The camera is already connected to Wi-Fi, but the router is:

• Not connected to Internet

• Poor network status

• The Wi-Fi signal is not stable due to obstacles or electronic
interference

• Ensure the LED indicator on the camera is ashing steady green.
See ‘LED Status’ section for details if otherwise.

• Ensure the camera is properly connected to power using the
included USB power adapter.

• Try repositioning the camera, router, or both to improve signal
strength.

• Check the camera lens for dirt, dust, spider webs. Clean the lens with
a soft, clean cloth.

• Remove the vinyl cover on the camera lens.

• Ensure audio function on camera is turned on.

• Ensure audio is turned up on viewing device.

• Ensure you have enabled “Human Detection” in the Device Settings
screen of the Imou LifeApp.

• Turn o Camera Shielding in Device Settings on the Imou Life app.

• Clean the camera lens of your Smartphone

• Ensure that there is enough light on the QR code

• Don’t hold the QR code too close to the camera

This product complies with the applicable CE marking directives
and standards:

Low Voltage (LVD) Directive 2014/35/EU.
Electromagnetic Compatibility (EMC) Directive 2014/30/EU.
Restrictions of Hazardous Substances (RoHS) Directive 2011/65/EU
and its amending Directive (EU) 2015/863.

A copy of the original declaration of conformity may be obtained from
Dahua Technology. The most up to date copy of the signed EU
Declaration of Conformity (DoC) can be found
www.imoulife.com/declaration-of-conformity

CE-Electromagnetic Compatibility (EMC)

This digital equipment is compliant with Class B according to EN 55032.

CE-Safety

This product complies with IEC/EN/UL 60950-1 or IEC/EN/UL 62368-1,
Safety of Information Technology Equipment.

Declaration of Conformity CE
(Only for the product has RF function)

Hereby, Dahua Technology declares that the radio equipment is
compliant with Radio Equipment Directive (RED) 2014/53/EU. The full
text of the EU declaration of conformity is available at www.imou­life.com/declaration-of-conformity

Kurzanleitung

A1

www.imoulife.com

Willkommen

Vielen Dank, dass Sie sich für IMOU entschieden haben.
Wir sind bestrebt, einfachere Produkte für das intelligente
Heim anzubieten. Wenn Sie Probleme bei der Verwendung
des Produkts haben, wenden Sie sich bitte an unser
Serviceteam.

Unsere Service-Mail lautet: [e-mail]

Detaillierte Installationsanweisungen und Videos sowie
häug gestellte Fragen, bitte nden Sie unter:
imoulife.com/support/help
Oder scannen Sie diesen QR-Code zur Hilfeseite.

Packungsinhalt

Kamera ×1 Stromkabel ×1 Netzteil ×1 Bohrlochschablone

Kurzanleitung ×1

Einführung in die Kamera

×1

LED-Anzeige

Objektiv

Built-in Mic

Eingebauter

MicroSD-

Kartensteckplatz

Rücksetz-/

Kopplungstaste

Hinweis:

Halten Sie die Rücksetz-/Kopplungstaste 10 Sekunden lang gedrückt, um die Kamera zurückzusetzen.

Lautsprecher

Ethernet­Anschluss

Stromanschluss

Das Muster der LED-Anzeigen ist in der folgenden Tabelle aufgeführt.

LED-Status/Gerätestatus

AUS

Rote LED leuchtet

Grüne LED blinkt

Grüne LED leuchtet
Rechte LED blinkt

Grüne und rote LED
blinken abwechselnd

Device Status

Abgeschaltet/LED Ausgeschaltet

Gerät fährt nach Rücksetzung hoch

Gerät fährt hoch

Gerätestörung

Warten auf

Ordnungsgemäßer Betrieb

Netzwerkverbindung fehlgeschlagen

Firmware-Update

Imou Life

Tips

i

Um die bestmögliche Funkübertragung zu gewährleisten, stellen Sie sicher,
dass zwischen Kamera und Router keine Hindernisse und elektromagnetische
Störungen vorhanden sind.

Setup

WIFI Name

Password

Next

Deckenmontage (optional)

Setup

Done

Montage-Oberäche

1

/-Decke
Montageschablone

Dübel

Mounting Plate

Selbstschneidende

2

Schraube

3

Kamera

+45

-10

DC

5V2A

Fehlerbehebung

Problem Lösungen

Kamera kann nicht

eingerichtet werden

The app says “

Failed to bind”

No picture / signal

Picture is not clear

No audio

Human detection

not working

Camera stuck

downwards

Phone is not

reading QR code

• Stellen Sie sicher, dass Ihr mobiles Gerät und die Kamera in
Reichweite Ihres WLAN-Routers sind.

• Vergewissern Sie sich, dass die LED-Anzeige an der Kamera grün
blinkt, bevor Sie mit der Einrichtung beginnen.

camera is already connected to Wi-Fi, but the router is:

• Not connected to Internet

• Poor network status

• The Wi-Fi signal is not stable due to obstacles or electronic
interference

• Ensure the LED indicator on the camera is ashing steady green.
See ‘LED Status’ section for details if otherwise.

• Ensure the camera is properly connected to power using the
included USB power adapter.

• Try repositioning the camera, router, or both to improve signal
strength.

• Check the camera lens for dirt, dust, spider webs. Clean the lens with
a soft, clean cloth.

• Remove the vinyl cover on the camera lens.

• Ensure audio function on camera is turned on.

• Ensure audio is turned up on viewing device.

• Ensure you have enabled “Human Detection” in the Device Settings
screen of the Imou LifeApp.

• Turn o Camera Shielding in Device Settings on the Imou Life app.

• Clean the camera lens of your Smartphone

• Ensure that there is enough light on the QR code

• Don’t hold the QR code too close to the camera

This product complies with the applicable CE marking directives
and standards:

Low Voltage (LVD) Directive 2014/35/EU.
Electromagnetic Compatibility (EMC) Directive 2014/30/EU.
Restrictions of Hazardous Substances (RoHS) Directive 2011/65/EU
and its amending Directive (EU) 2015/863.

A copy of the original declaration of conformity may be obtained from
Dahua Technology. The most up to date copy of the signed EU
Declaration of Conformity (DoC) can be found
www.imoulife.com/declaration-of-conformity

CE-Electromagnetic Compatibility (EMC)

This digital equipment is compliant with Class B according to EN 55032.

CE-Safety

This product complies with IEC/EN/UL 60950-1 or IEC/EN/UL 62368-1,
Safety of Information Technology Equipment.

Declaration of Conformity CE
(Only for the product has RF function)

Hereby, Dahua Technology declares that the radio equipment is
compliant with Radio Equipment Directive (RED) 2014/53/EU. The full
text of the EU declaration of conformity is available at www.imou­life.com/declaration-of-conformity

Guía de inicio rápido

A1

www.imoulife.com

Bienvenido

Gracias por elegir IMOU
Nuestra misión es proporcionar productos fáciles de usar
para un hogar inteligente. Si tiene problemas usando el
producto, por favor diríjase a nuestro equipo de atención
al cliente antes de devolver su producto.
Nuestro correo electrónico de servicio:
[e-mail]
Nos comprometemos a contestarle en 24 horas.

Encontrará instrucciones y videos detallados de instalación,
preguntas más frecuentes en: imoulife.com/support/help
O escanee este código QR para las páginas
de ayuda.

Contenido del paquete

Cámara ×1

Guía de inicio rápido

×1

Cable de alimentación

×1

Adaptador de corriente

Introducción a la cámara

Plantilla de

×1

posicionamiento ×1

Indicador LED

Lente

Micrófono
integrado

Ranura para
tarjeta Micro SD

Altavoz

integrado

Puerto

Ethernet

Botón de reinicio/
emparejamiento

Nota:

Mantenga pulsado el botón de reinicio/emparejamiento durante 10 segundos para reiniciar
la cámara.

Puerto de

alimentación

El patrón de los indicadores LED se incluye en la siguiente tabla.

Estado LED

APAGADA

Luz roja encendida

Luz verde parpadeante

Luz verde encendida
Luz derecha parpadeante
Luz verde y luz roja parpadeando
alternativamente

Estado del aparato

Apagada/LED apagada
Nuevo arranque después del reinicio
Arranque
Avería del dispositivo
En espera de la red

Funcionando correctamente
Fallo de conexión de red

Actualización de rmware

Imou Life

Consejos

i

Para garantizar el mejor rendimiento inalámbrico posible, por favor asegúrese
de que no hay obstáculos ni interferencias electromagnéticas entre la cámara
y el enrutador.

Setup

WIFI Name

Password

Next

Montaje en el techo (Opcional)

Supercie de

1

montaje/techo

Plantilla de
posicionamiento

Taco de expansión

Mounting Plate

Tornillo

2

autorroscante

Cámara

3

Setup

Done

+45

-10

DC

5V2A

Troubleshooting

Problem Solution

Cannot set up camera

The APP says "Failed

to congure device

network"

The app says “

Failed to bind”

No picture / signal

Picture is not clear

No audio

Human detection

not working

Camera stuck

downwards

Phone is not

reading QR code

• Ensure your mobile device and the camera are within range of your
Wi-Fi router.

• Ensure the LED indicator on the camera isashing green before
beginning setup.

• Reset your Camera and connect it again.

• Some cameras only support 2.4GHz, while some routers have dual
band, 2.4G/5G. Make sure you are connecting 2.4GHz only.
The camera is already connected to Wi-Fi, but the router is:

• Not connected to Internet

• Poor network status

• The Wi-Fi signal is not stable due to obstacles or electronic
interference

• Ensure the LED indicator on the camera is ashing steady green.
See ‘LED Status’ section for details if otherwise.

• Ensure the camera is properly connected to power using the
included USB power adapter.

• Try repositioning the camera, router, or both to improve signal
strength.

• Check the camera lens for dirt, dust, spider webs. Clean the lens with
a soft, clean cloth.

• Remove the vinyl cover on the camera lens.

• Ensure audio function on camera is turned on.

• Ensure audio is turned up on viewing device.

• Ensure you have enabled “Human Detection” in the Device Settings
screen of the Imou LifeApp.

• Turn o Camera Shielding in Device Settings on the Imou Life app.

• Clean the camera lens of your Smartphone

• Ensure that there is enough light on the QR code

• Don’t hold the QR code too close to the camera

This product complies with the applicable CE marking directives
and standards:

Low Voltage (LVD) Directive 2014/35/EU.
Electromagnetic Compatibility (EMC) Directive 2014/30/EU.
Restrictions of Hazardous Substances (RoHS) Directive 2011/65/EU
and its amending Directive (EU) 2015/863.

A copy of the original declaration of conformity may be obtained from
Dahua Technology. The most up to date copy of the signed EU
Declaration of Conformity (DoC) can be found
www.imoulife.com/declaration-of-conformity

CE-Electromagnetic Compatibility (EMC)

This digital equipment is compliant with Class B according to EN 55032.

CE-Safety

This product complies with IEC/EN/UL 60950-1 or IEC/EN/UL 62368-1,
Safety of Information Technology Equipment.

Declaration of Conformity CE
(Only for the product has RF function)

Hereby, Dahua Technology declares that the radio equipment is
compliant with Radio Equipment Directive (RED) 2014/53/EU. The full
text of the EU declaration of conformity is available at www.imou­life.com/declaration-of-conformity

Guide de démarrage rapide

A1

www.imoulife.com

Bienvenue

Merci d’avoir choisi IMOU.

Nous nous consacrons à fournir des produits pour la maison

intelligente plus faciles à utiliser. Si vous rencontrez des dicultés

lors de l’utilisation du produit, veuillez contacter notre équipe

technique avant de renvoyer votre produit.

Notre courriel de service: service.global @imoulife.com

Nous nous engageons à vous répondre dans les 24heures.

Des instructions d'installation détaillées et des vidéos, les questions

fréquemment posées peuvent être trouvées sur: imoulife.com/sup-

port/help

Ou scannez ce code QR pour accéder à la page d'aide.

Contenu de l’emballage

Caméra ×1 Cable de alimentación×1Adaptateur secteur

Guide de démarrage rapide

×1

Introduction à la caméra

×1

Patron d’installation

×1

Indicateur
lumineux

Objectif

Microphone
intégré

Haut-parleur

Emplacement de
carte micro-SD

Touche de
réinitialisation
/couplage

Remarque:

Appuyez et maintenez la touche de réinitialisation/couplage pendant 10 secondes pour réinitialiser
la caméra.

intégré

Port Ethernet

Port d’alimentation

Le schéma des voyants est inclus dans le tableau suivant.

Statut du voyant

ARRÊT

Allumé en rouge

Clignotant en vert
Allumé en vert
Clignotement du voyant droit

Voyant vert et voyant rouge
clignotant en alternance

État de l’appareil

Éteint/Voyant éteint
Redémarrage après remise à zéro
Amorçage
Dysfonctionnement de l'appareil
En attente de connexion réseau

Fonctionnement normal
Échec de connexion au réseau

Mise à jour du micrologiciel

Imou Life

i

Conseils

Pour garantir les meilleures performances sans l possible, veuillez vous
assurer qu’il n’y a pas d’obstacles ni d’interférences électromagnétiques entre
la caméra et le routeur.

Setup

WIFI Name

Password

Next

Montage au plafond (facultatif)

Setup

Done

Surface de

1

montage/plafond

Patron d’installation

Cheville à expansion

Mounting Plate

Vis autotaraudeuse

2

3

Caméra

+45

-10

DC

5V2A

Troubleshooting

Problem Solution

Cannot set up camera

The APP says "Failed

to congure device

network"

The app says “

Failed to bind”

No picture / signal

Picture is not clear

No audio

Human detection

not working

Camera stuck

downwards

Phone is not

reading QR code

• Ensure your mobile device and the camera are within range of your
Wi-Fi router.

• Ensure the LED indicator on the camera isashing green before
beginning setup.

• Reset your Camera and connect it again.

• Some cameras only support 2.4GHz, while some routers have dual
band, 2.4G/5G. Make sure you are connecting 2.4GHz only.
The camera is already connected to Wi-Fi, but the router is:

• Not connected to Internet

• Poor network status

• The Wi-Fi signal is not stable due to obstacles or electronic
interference

• Ensure the LED indicator on the camera is ashing steady green.
See ‘LED Status’ section for details if otherwise.

• Ensure the camera is properly connected to power using the
included USB power adapter.

• Try repositioning the camera, router, or both to improve signal
strength.

• Check the camera lens for dirt, dust, spider webs. Clean the lens with
a soft, clean cloth.

• Remove the vinyl cover on the camera lens.

• Ensure audio function on camera is turned on.

• Ensure audio is turned up on viewing device.

• Ensure you have enabled “Human Detection” in the Device Settings
screen of the Imou LifeApp.

• Turn o Camera Shielding in Device Settings on the Imou Life app.

• Clean the camera lens of your Smartphone

• Ensure that there is enough light on the QR code

• Don’t hold the QR code too close to the camera

This product complies with the applicable CE marking directives
and standards:

Low Voltage (LVD) Directive 2014/35/EU.
Electromagnetic Compatibility (EMC) Directive 2014/30/EU.
Restrictions of Hazardous Substances (RoHS) Directive 2011/65/EU
and its amending Directive (EU) 2015/863.

A copy of the original declaration of conformity may be obtained from
Dahua Technology. The most up to date copy of the signed EU
Declaration of Conformity (DoC) can be found
www.imoulife.com/declaration-of-conformity

CE-Electromagnetic Compatibility (EMC)

This digital equipment is compliant with Class B according to EN 55032.

CE-Safety

This product complies with IEC/EN/UL 60950-1 or IEC/EN/UL 62368-1,
Safety of Information Technology Equipment.

Declaration of Conformity CE
(Only for the product has RF function)

Hereby, Dahua Technology declares that the radio equipment is
compliant with Radio Equipment Directive (RED) 2014/53/EU. The full
text of the EU declaration of conformity is available at www.imou­life.com/declaration-of-conformity

Guida Rapida

A1

www.imoulife.com

Benvenuti

Grazie per aver scelto IMOU.

Il nostro obiettivo è quello di fornire prodotti per la domotica più

facili da utilizzare. In caso di problemi durante l’utilizzo del

prodotto, si prega di contattare il nostro team di assistenza prima

di restituire il prodotto. La nostra e-mail per il servizio di assistenza:
[e-mail]

Promettiamo di rispondere entro 24 ore.

Istruzioni dettagliate per l'installazione e video, domande frequenti

sono disponibili all'indirizzo: imoulife.com/support/help

Oppure scansiona questo codice QR per la pagina di aiuto.

Contenuto della confezione

Telecamera ×1 Cavo di alimentazione×1Adattatore

Guida introduttiva

×1

×1

Introduzione alla telecamera

Dima di posizionamento

×1

Indicatore LED

Obiettivo

Microfono
integrato

Altoparlante

Slot per scheda

micro-SD

Pulsante

Reimposta/

Associa

Nota:

Tenere premuto per 10 secondi il pulsante Reimposta/Associa per reimpostare la telecamera.

integrato

Porta Ethernet

Porta di

alimentazione

Gli indicatori LED sono descritti nella tabella seguente.

Stato LED

SPENTO

Luce rossa accesa

Luce verde lampeggiante
Luce verde accesa

Luce rossa lampeggiante
La luce verde e quella rossa
lampeggiano in alternanza

Stato dispositivo

Spento/LED spento
Riavvio dopo il ripristino
Avvio
Malfunzionamento del dispositivo
In attesa di rete

Funzionamento normale

Connessione di rete non riuscita

Aggiornamento del rmware

Imou Life

Suggerimenti

i

Per garantire le migliori prestazioni wireless possibili, assicurarsi che non ci
siano ostacoli e interferenze elettromagnetiche tra la telecamera e il router.

Setup

WIFI Name

Password

Next

Montaggio a soffitto (opzionale)

1

2

3

Setup

Done

Montaggio a
parete/sotto

Dima di
posizionamento

Bullone di
espansione

Mounting Plate

Vite autolettante

Telecamera

+45

-10

DC

5V2A

Troubleshooting

Problem Solution

Cannot set up camera

The APP says "Failed

to congure device

network"

The app says “

Failed to bind”

No picture / signal

Picture is not clear

No audio

Human detection

not working

Camera stuck

downwards

Phone is not

reading QR code

• Ensure your mobile device and the camera are within range of your
Wi-Fi router.

• Ensure the LED indicator on the camera isashing green before
beginning setup.

• Reset your Camera and connect it again.

• Some cameras only support 2.4GHz, while some routers have dual
band, 2.4G/5G. Make sure you are connecting 2.4GHz only.
The camera is already connected to Wi-Fi, but the router is:

• Not connected to Internet

• Poor network status

• The Wi-Fi signal is not stable due to obstacles or electronic
interference

• Ensure the LED indicator on the camera is ashing steady green.
See ‘LED Status’ section for details if otherwise.

• Ensure the camera is properly connected to power using the
included USB power adapter.

• Try repositioning the camera, router, or both to improve signal
strength.

• Check the camera lens for dirt, dust, spider webs. Clean the lens with
a soft, clean cloth.

• Remove the vinyl cover on the camera lens.

• Ensure audio function on camera is turned on.

• Ensure audio is turned up on viewing device.

• Ensure you have enabled “Human Detection” in the Device Settings
screen of the Imou LifeApp.

• Turn o Camera Shielding in Device Settings on the Imou Life app.

• Clean the camera lens of your Smartphone

• Ensure that there is enough light on the QR code

• Don’t hold the QR code too close to the camera

This product complies with the applicable CE marking directives
and standards:

Low Voltage (LVD) Directive 2014/35/EU.
Electromagnetic Compatibility (EMC) Directive 2014/30/EU.
Restrictions of Hazardous Substances (RoHS) Directive 2011/65/EU
and its amending Directive (EU) 2015/863.

A copy of the original declaration of conformity may be obtained from
Dahua Technology. The most up to date copy of the signed EU
Declaration of Conformity (DoC) can be found
www.imoulife.com/declaration-of-conformity

CE-Electromagnetic Compatibility (EMC)

This digital equipment is compliant with Class B according to EN 55032.

CE-Safety

This product complies with IEC/EN/UL 60950-1 or IEC/EN/UL 62368-1,
Safety of Information Technology Equipment.

Declaration of Conformity CE
(Only for the product has RF function)

Hereby, Dahua Technology declares that the radio equipment is
compliant with Radio Equipment Directive (RED) 2014/53/EU. The full
text of the EU declaration of conformity is available at www.imou­life.com/declaration-of-conformity

Snelstartgids

A1

www.imoulife.com

Welkom

Bedankt dat u voor Imou heeft gekozen.

Onze toewijding is om u eenvoudige Smart Home producten
te bieden. Als u problemen ervaart met het gebruik van uw
product, neem dan eerst contact op met onze service team:
[e-mail]

Gedetailleerde installatie-instructies en video's, veelgestelde
vragen zijn te vinden op: imoulife.com/support/help
Of scan deze QR-code naar de helppagina.

Inhoud verpakking

Camera ×1 Netsnoer

Snelstarthandleiding

×1

×1

Introductie camera

Spanningsadapter

×1

Kaart installatiepositie

×1

Led-indicator

Lens

Ingebouwde
microfoon

Ingebouwde

MicroSD

-kaartsleuf

Reset

-/koppelknop

Opmerking:

Druk de reset-/koppelknop 10 seconden in om de camera te resetten.

luidspreker

Ethernetpoort

Stroomaansluiting

Het patroon van led-indicatoren wordt weergegeven in de volgende tabel.

Ledstatus

UIT

Rood lampje aan

Groen lampje knippert
Groen lampje aan
Rood lampje knippert
Groen lampje en rood lampje
knipperen afwisselend

Apparaatstatus

Uitgeschakeld/led uit
Opnieuw opstarten na reset
Bezig met opstarten
Storing van het apparaat
Wachten op netwerk

Werkt zoals dat moet
Netwerkverbinding mislukt

Bijwerken rmware

Imou Life

Tips

i

Zorg voor de best mogelijke draadloze prestatie dat er geen obstakels en
elektromagnetische interferentie tussen de camera en router aanwezig zijn.

Setup

WIFI Name

Password

Next

Plafondbevestiging (optioneel)

Setup

Done

Montageoppervlak/

1

plafond

Kaart installatiepositie

Expansiebout

Mounting Plate

2

Zelftappende schroef

3

Camera

+45

-10

DC

5V2A

Troubleshooting

Problem Solution

Cannot set up camera

The APP says "Failed

to congure device

network"

The app says “

Failed to bind”

No picture / signal

Picture is not clear

No audio

Human detection

not working

Camera stuck

downwards

Phone is not

reading QR code

• Ensure your mobile device and the camera are within range of your
Wi-Fi router.

• Ensure the LED indicator on the camera isashing green before
beginning setup.

• Reset your Camera and connect it again.

• Some cameras only support 2.4GHz, while some routers have dual
band, 2.4G/5G. Make sure you are connecting 2.4GHz only.
The camera is already connected to Wi-Fi, but the router is:

• Not connected to Internet

• Poor network status

• The Wi-Fi signal is not stable due to obstacles or electronic
interference

• Ensure the LED indicator on the camera is ashing steady green.
See ‘LED Status’ section for details if otherwise.

• Ensure the camera is properly connected to power using the
included USB power adapter.

• Try repositioning the camera, router, or both to improve signal
strength.

• Check the camera lens for dirt, dust, spider webs. Clean the lens with
a soft, clean cloth.

• Remove the vinyl cover on the camera lens.

• Ensure audio function on camera is turned on.

• Ensure audio is turned up on viewing device.

• Ensure you have enabled “Human Detection” in the Device Settings
screen of the Imou LifeApp.

• Turn o Camera Shielding in Device Settings on the Imou Life app.

• Clean the camera lens of your Smartphone

• Ensure that there is enough light on the QR code

• Don’t hold the QR code too close to the camera

This product complies with the applicable CE marking directives
and standards:

Low Voltage (LVD) Directive 2014/35/EU.
Electromagnetic Compatibility (EMC) Directive 2014/30/EU.
Restrictions of Hazardous Substances (RoHS) Directive 2011/65/EU
and its amending Directive (EU) 2015/863.

A copy of the original declaration of conformity may be obtained from
Dahua Technology. The most up to date copy of the signed EU
Declaration of Conformity (DoC) can be found
www.imoulife.com/declaration-of-conformity

CE-Electromagnetic Compatibility (EMC)

This digital equipment is compliant with Class B according to EN 55032.

CE-Safety

This product complies with IEC/EN/UL 60950-1 or IEC/EN/UL 62368-1,
Safety of Information Technology Equipment.

Declaration of Conformity CE
(Only for the product has RF function)

Hereby, Dahua Technology declares that the radio equipment is
compliant with Radio Equipment Directive (RED) 2014/53/EU. The full
text of the EU declaration of conformity is available at www.imou­life.com/declaration-of-conformity

Guia rápido

Ranger 2

www.imoulife.com

Bem-vindo

Obrigado por escolher a IMOU.

Estamos empenhados em fornecer produtos inteligentes e

simplicados para o lar. Se tiver problemas ao utilizar o produto,

contacte a nossa equipa de assistência antes de devolver o produto.

O nosso e-mail de assistência: [e-mail] Prometemos

responder no prazo de 24 horas.

Instruções e vídeos de instalação detalhados, perguntas freqüentes

podem ser encontradas em: imoulife.com/support/help

Ou digitalize este código QR para a página de ajuda.

Conteúdo da embalagem

Câmara

×1

Guia de Início Rápido

×1

Cabo de alimentação

×1

Apresentação da câmara

Adaptador

×1

Mapa de posicionamento

×1

Indicador LED

Objetiva

Microfone
integrado

Ranhura para

cartões micro SD

Botão Reset/Pair

Nota:

Prima sem soltar o botão Reset/Pair durante 10 segundos para repor a câmara.

O padrão dos indicadores LED está incluído na tabela seguinte.

Estado do LED Estado do dispositivo

DESLIGADO

Luz vermelha acesa

Luz verde intermitente
Luz verde acesa

Luz vermelha intermitente
Luz verde e luz vermelha
intermitentes alternadamente

Desligado/LED desligado
Reiniciar após a reposição
Arranque
Avaria do dispositivo
À espera da rede

A funcionar corretamente
Ligação à rede falhou

Atualização do rmware

Altifalante

integrado

Entrada
Ethernet

Porta de

alimentação

Imou Life

i

Dicas

Para assegurar o melhor desempenho possível do sistema sem os,
certique-se de que não existem obstáculos e interferência eletromagnética
entre a câmara e o router.

Setup

WIFI Name

Password

Next

Montagem no teto (Opcional)

Setup

Done

Superfície de

1

montagem/Teto
Mapa de
posicionamento

Parafuso de expansão

Mounting Plate

Parafuso

2

autoperfurante

Câmara

3

+45

-10

DC

5V2A

Troubleshooting

Problem Solution

Cannot set up camera

The APP says "Failed

to congure device

network"

The app says “

Failed to bind”

No picture / signal

Picture is not clear

No audio

Human detection

not working

Camera stuck

downwards

Phone is not

reading QR code

• Ensure your mobile device and the camera are within range of your
Wi-Fi router.

• Ensure the LED indicator on the camera isashing green before
beginning setup.

• Reset your Camera and connect it again.

• Some cameras only support 2.4GHz, while some routers have dual
band, 2.4G/5G. Make sure you are connecting 2.4GHz only.
The camera is already connected to Wi-Fi, but the router is:

• Not connected to Internet

• Poor network status

• The Wi-Fi signal is not stable due to obstacles or electronic
interference

• Ensure the LED indicator on the camera is ashing steady green.
See ‘LED Status’ section for details if otherwise.

• Ensure the camera is properly connected to power using the
included USB power adapter.

• Try repositioning the camera, router, or both to improve signal
strength.

• Check the camera lens for dirt, dust, spider webs. Clean the lens with
a soft, clean cloth.

• Remove the vinyl cover on the camera lens.

• Ensure audio function on camera is turned on.

• Ensure audio is turned up on viewing device.

• Ensure you have enabled “Human Detection” in the Device Settings
screen of the Imou LifeApp.

• Turn o Camera Shielding in Device Settings on the Imou Life app.

• Clean the camera lens of your Smartphone

• Ensure that there is enough light on the QR code

• Don’t hold the QR code too close to the camera

This product complies with the applicable CE marking directives
and standards:

Low Voltage (LVD) Directive 2014/35/EU.
Electromagnetic Compatibility (EMC) Directive 2014/30/EU.
Restrictions of Hazardous Substances (RoHS) Directive 2011/65/EU
and its amending Directive (EU) 2015/863.

A copy of the original declaration of conformity may be obtained from
Dahua Technology. The most up to date copy of the signed EU
Declaration of Conformity (DoC) can be found
www.imoulife.com/declaration-of-conformity

CE-Electromagnetic Compatibility (EMC)

This digital equipment is compliant with Class B according to EN 55032.

CE-Safety

This product complies with IEC/EN/UL 60950-1 or IEC/EN/UL 62368-1,
Safety of Information Technology Equipment.

Declaration of Conformity CE
(Only for the product has RF function)

Hereby, Dahua Technology declares that the radio equipment is
compliant with Radio Equipment Directive (RED) 2014/53/EU. The full
text of the EU declaration of conformity is available at www.imou­life.com/declaration-of-conformity