PGS10 Series Grippers
User instructions
for PGS10 Series
Grippers
Engineering
GREAT Solutions
User Instruction for PGS10 Series Gripper
Table of contents
Section Page
Reference ...........................................................................................................I .......................3
Purpose ............................................................................................................ II .......................3
Scope .............................................................................................................. III .......................3
Safety ............................................................................................................... IV .......................3
Applicable Documents ......................................................................................V .......................3
Equipment Required ........................................................................................VI ....................... 3
Procedures ......................................................................................................VII .......................3
Cleaning and Maintenance ............................................................................. VIII .....................10
Quality Assurance Requirements ......................................................................IX ..................... 10
Specifications ....................................................................................................X .....................11
Warning and Warrenty ...............................................................................................................11
Revisions record
Revisions ECN. NO. BY DAT E
REL 25455 MGF 11/21/07
001 25455 MS 6/12/08
002 25779 MGF 02/19/09
003 25881 RRH 09/25/09
004 26054 MGF 11/27/12
DRAWN DAT E
MFG 11/02/07
CHECKED DAT E
RRH 10/05/09
DES ENG D ATE
JJA 11/02/07
APPR, DAT E
DAM 10/05/09
DES ENG D ATE
JJA 11/27/12
DES ENG D ATE
RRH 11/27/12
02
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
P/N 00537UI REV: 004
10/15
I. Reference:
001POL Quality Policy
II. Purpose:
This document instructs the operator how to use the
PGS10 & 11 Grippers
III. Scope:
This work instruction covers Port Size and Operation, Unlocking of
Jaws & Setting Open Jaw Angle.
IV. Safety:
Safety glasses or approved eye protection must be worn at all
times. Steps involving chemical bonding require the use of proper
ventilation and skin protection in accordance with manufacturer’s
MSDS.
V. Applicable Documents:
00768SP – Sales Page – PGS1XCXXXXXXXXX (Chisel Jaw)
00732SP - Sales Page – PGS1XRXXXXXXXXX (Regular Jaw)
00770SP - Sales Page – PGS1XFXXXXXXXXX (Flange Jaw)
00775SP – Spare Parts List for PGS1X Gripper Series
User Instruction for PGS10 Series Gripper
VI. Equipment Required:
Standard Bench Tools
VII. Procedures
A. Port Size and Operation
1. Ports are available in 1/8" NPS or 1/8 Rc.
Gripper open
Gripper close
letter “C” to identify part
10/15
P/N 00537UI REV: 004
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
03
User Instruction for PGS10 Series Gripper
B. Gripper Unlock
1. Release jaw by using a hex key or flat screwdriver and pushing on drive pin through
slot in side plate
C. Jaw Removal
1. Unlock gripper as shown in step B and remove pad(s) from existing jaws. Set a side
for reassembly.
2. Top jaw should always be removed first. Remove SHCS from side plate or indirect
sensor. Rotate side plate/sensor up to about 45° and remove side plate/sensor from
gripper. Set SHCS and Side Plate/Sensor aside for re-assembly. Remove bumper
from gripper.
3. Remove jaw from gripper and flip gripper over to remove other jaw
4. Remove SHCS from side plate/sensor. Rotate side plate/sensor up to about 45° angle
and remove from gripper. Set SHCS and Side Plate/Sensor aside for re-assembly.
04
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
P/N 00537UI REV: 004
10/15
User Instruction for PGS10 Series Gripper
C. Jaw Removal (cont.)
5. Remove bushing from lower jaw using a small flat screwdriver or hex key and set aside
for re-assembly. Lower jaw should be rotated completely down before removal. Lift up on
front of jaw by pad so there is an angle between jaw and frame. Remove lower jaw from
gripper.
Angle
D. Jaw Replacement
1. For lower jaws (10151,11105,11105-01, 11105-02, 11106, 11106-01, 11106-
02,11103,12978,12978-01, 12978-02, 12985, 12985-01, 12985-02): Apply grease to
cam and inside of jaw. Angle new jaw so that tail of jaw goes in pocket of frame. Align
pivot hole with boss and drive pin with the bottom side of the cam slot. Carefully slide
jaw over boss and onto gripper. Replace bushing over pin and into cam. Apply grease
to outside of jaw.
Tail of jaw
in pocket
2. Refer to step F for installing a Side Plate or Indirect Sensor.
3. Flip gripper over for top jaw installation
4. For upper jaws: Apply grease to cam and inside of jaw. Replace bushing over drive
pin and onto gripper. Align hole in jaw with boss on frame and cam with bushing.
Slide jaw over boss and drive pin so that jaw rests on gripper. Apply grease to
outside of jaw.
5. Refer to step E-2 to set bumper position. Refer to step B for installing a Side Plate or
Indirect Sensor.
10/15
P/N 00537UI REV: 004
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
05
User Instruction for PGS10 Series Gripper
E. Setting Jaw Open Angle
1. Look for bumper which should be on the upper jaw side. Remove M5X12mm SHCS
from side plate. If indirect sensor is in place of side plate remove M5X30mm from
indirect sensor. Rotate side plate/sensor up to about a 45° and remove from gripper.
Set SHCS and Side Plate/Sensor aside for re-assembly. Remove bumper from
gripper.
2. Insert bumper into new position, based on required open jaw angle. Bumpers should
only be on the top jaw side of gripper. Jaws do not need to be removed to change
bumper position. Insert bumper into frame and insure bumper is seated properly.
22° Open
Jaw Angle
45° Open
Jaw Angle
70° Open
Jaw Angle
F. Installing a Side Plate or Indirect Sensor
1. With the Side Plate at 45°,align pins of side plate with slots of frame. Slide pins into
slot. When pins are fully seated, rotate side plate and slide down onto frame.
06
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
P/N 00537UI REV: 004
10/15
User Instruction for PGS10 Series Gripper
F. Installing a Side Plate or Indirect Sensor (cont.)
2. If an Indirect Sensor is to be installed, move brass bushing in sensor to align with
drive pin in gripper. This must be done to correctly install sensor. Align dowel pins with
slots of frame. Once pins are fully into slots, rotate sensor down onto frame. As rotation
begins make sure bushing and drive pin are still aligned.
Note: Whenever any part of the gripper is replaced including pads the sensor will need to
be recalibrated, see step J.
3. Clean and apply Loctite 262 or equivalent to M5 X 12mm SHCS for side plate or M5 X
30mm SHCS for sensor. Insert through side plate/sensor and into frame. Tighten M5
SHCS to 72in-lb.
Side Plate
Indirect Sensor
G. Pad Replacement
1. Unlock jaws on gripper & open jaws to get access to pads. Side plates/sensor
DO NOT need to be removed. Refer to Gripper Unlock section B.
2. Remove M5X8mm SHCS from jaw.
3.
10/15
P/N 00537UI REV: 004
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
07
User Instruction for PGS10 Series Gripper
3. Apply Loctite 262 to M5 X 8mm SHCS and insert into one of the jaws. Take
replacement pads and insert it into the opposite side of the jaw with SHCS sticking out.
Thread SHCS into pad and tighten to 72in-lb. Repeat step for other jaw. Chisel jaws
only require one pad
H. Calibrating In-Direct Sensor
Sensor must be calibrated whenever any part of the gripper is replaced including pads.
1. Part Present
a. To program the sensor for a particular material thickness, apply air to the gripper
and grip on the material thickness which is to be used for the particular job.
With an object such as a small Allen wrench, press the button until the Red LED
corresponding to the material range of the job lights as shown on the label.
b) Verify calibration:
(1) Close the gripper with no material between the pads. The LED should be o.
(2) Close the gripper on a single blank of material. The Red LED corresponding to your
material range should be on.
2. Double Blank
a) To program the sensor for a particular material thickness, apply air to the gripper
and grip on the material thickness which is to be used for the particular job. With
an object such as a small Allen wrench, press the button until the Red LED(s)
corresponding to the material range of the job lights as shown on the label.
08
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
P/N 00537UI REV: 004
10/15
User Instruction for PGS10 Series Gripper
H. Calibrating In-Direct Sensor (cont.)
b) Verify calibration:
(1) Close the gripper with no material between the pads. The LED(s) should be o.
(2) Close the gripper on a single blank of material. The Red LED(s) corresponding to
you material range should be on.
I. Installing an In-Pad Sensor
1. If an In-Pad Sensor is to be installed, it goes on top of the side plate assembly.
Wrap sensor cable through holder and align holes on side plate. Clean and apply
Red Loctite 262 or equivalent to 2X M5 X 10mm SHCS and thread thru sensor into
side plate. Tighten both SHCS to 36in-lb.
2. Shim is only used for part numbers listed. If a shim is to be used on an angle pad,
smaller tabs go on the narrow side of the pads.
PGS10FXXXXX1XXX
PGS10CXXXXX1XXX
PGS10DXXXXX4XXX
PGS10EXXXXX7XXX
PGS10SXXXXX1XXX
PGS10TXXXXX4XXX
PGS10UXXXXX7XXX
PGS10VXXXXX1XXX
PGS10WXXXXX4XXX
PGS10YXXXXX7XXX
10/15
P/N 00537UI REV: 004
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
Small TabsPGS10RXXXXX1XXX
09
User Instruction for PGS10 Series Gripper
3. Apply Red Loctite 262 or equivalent to sensor stud, place thru jaw and tighten sensor
nut to 72in-lb.
Cable should follow
the contour of the
gripper jaw
VIII. Cleaning and Maintenance:
A) Remove excess grease from outer surfaces of gripper.
B) No required maintenance.
IX. Quality Assurance Requirements:
A) Verify that jaws shall open freely. Look for any irregular movement,
binding, or interference.
X. Specifications:
Gripper Throat Depth
Inch (mm)
PGS10C
.76 19.3 1.27 (32.3) 60 psi (413kPa) Min. –
Flange Height
Inch (mm)
Working Pressure Double Sided Grip
100 psi (689 kPa) Max.
PGS10D
.76 19.3 1.27 (32.3) 60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
PGS10E
.76 19.3 1.27 (32.3) 60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
PGS10F
.92 23.4 1.21 (30.6mm) 60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
PGS10R
.75 19 1.03 (26.3mm) 60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
PGS10S
.76 19.3 1.27 (32.3) 60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
PGS10T
.76 19.3 1.27 (32.3) 60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
PGS10U
.76 19.3 1.27 (32.3) 60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
PGS10V
.76 19.3 1.27 (32.3) 60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
PGS10W
.76 19.3 1.27 (32.3) 60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
PGS10Y
.76 19.3 1.27 (32.3) 60 psi (413kPa) Min. –
100 psi (689 kPa) Max.
Cable storage loop
can be adjusted with
a push/pull motion to
provide more or less
cable slack in gripper
jaw area
Force Up To
450lbs (200kgf) @ 80
psi (551kPa)
450lbs (200kgf) @ 80
psi (551kPa)
450lbs (200kgf) @ 80
psi (551kPa))
450lbs (200kgf) @ 80
psi (551kPa)
450lbs (200kgf) @ 80
psi (551kPa)
450lbs (200kgf) @ 80
psi (551kPa)
450lbs (200kgf) @ 80
psi (551kPa)
450lbs (200kgf) @ 80
psi (551kPa)
450lbs (200kgf) @ 80
psi (551kPa)
450lbs (200kgf) @ 80
psi (551kPa)
450lbs (200kgf) @ 80
psi (551kPa)
Actuation Time
.050±.010 sec close /
<.090 sec open
.050±.010 sec close /
<.090 sec open
.050±.010 sec close /
<.090 sec open
.050±.010 sec close /
<.090 sec open
.050±.010 sec close /
<.090 sec open
050±.010 sec close /
<.090 sec open
.050±.010 sec close /
<.090 sec open
.050±.010 sec close /
<.090 sec open
.050±.010 sec close /
<.090 sec open
.050±.010 sec close /
<.090 sec open
.050±.010 sec close /
<.090 sec open
10
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
P/N 00537UI REV: 004
10/15
User Instruction for PGS10 Series Gripper
Chisel jaw / shovel Regular / flange jaw
Single blank
thickness
0.50mm to 2.0mm
2.01mm to 3.5mm
3.51mm to 5.0mm
5.01mm to 6.5mm
6.51mm to 8.0mm
8.01mm to 9.5mm
Note 1: A shim is required under a black pad when it is installed on a chisel jaw gripper. This shim is included in all black replacement pad kits for the chisel jaw gripper.
Movable jaw
pad color
Opposing fixed
jaw color
Moveable jaw
pad color
Black (note 1) Black Black
Silver Black Silver
Black (note 1) Silver Gold
Silver Silver n/a
Black (note 1) Gold n/a
Silver Gold n/a
Opposing jaw
pad color
Black
Silver
Silver
n/a
n/a
n/a
Warning
Improper selection, misuse, age or malfunction of components used in
systems can cause failure in various modes. The system designer is warned
to consider the failure modes of all component parts and to provide adequate
safeguards to prevent personal injury or damage to equipment or property
in the event of such failure modes. System designers and end users are
cautioned to consult instruction sheets and specifications available from the
factory. The system designer/end user is responsible for verifying that all
requirements for the application are met.
Proposition 65: These products may contain chemicals known to the state of
California to cause cancer, or birth defects, or other reproductive harm.
10/15
P/N 00537UI REV: 004
Our policy is one of continued research and development. We therefore reserve the right to amend,
without notice, the specifications given in this document. © 2015 Norgren Automation Solutions, LLC.
Warranty
The products described herein are warranted subject to seller’s Standard
Terms and Condition of Sale, available at seller’s website.
11
Loading...