IMG STAGE LINE Moving Beamer BEAM-1800 User Manual
Moving Beamer
BEAM-1800
User Guide
Please read these instructions carefully before use
Moving Beamer BEAM-1800
1-
Moving Beamer BEAM-1800
2-
CONTENTS
1. Safety Instruction ...............................................................................................................3
2. Installation................................................................................................................................5
3. Technical Specification..................................................................................................7
4. Description............................................................................................................................11
4.1 Description of the fixture.....................................................................11
4.2 Control Panel..................................................................................... 12
5. Lamp.......................................................................................................................................... 13
6. How To Set The Unit......................................................................................................14
6.1 Display Status When Power On......................................................... 14
6.2 Main Function.................................................................................... 15
6.3. Home Position Adjustment ............................................................... 25
6.4. Memory card..................................................................................... 26
6.5. Error Information............................................................................... 28
7. Control By Universal DMX Controller...............................................................28
7.1 Connection ........................................................................................ 28
7.2 Channel Mode Setting....................................................................... 29
7.3 Address Setting ................................................................................. 30
7.4 DMX 512 Configuration ..................................................................... 30
8. Update Software................................................................................................................ 38
9. Troubleshooting................................................................................................................ 38
10. Fixture Cleaning.............................................................................................................40
Moving Beamer BEAM-1800
3-
1. Safety Instruction
WARNIN
G
Please keep this User Manual for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty.
The dealer will not accept liability for any resulting defects or problems.
y Unpack and check carefully that there is no transportation damage before using the
unit.
y The unit is for indoor use only. Use only in a dry location.
y Do install and operate by qualified operator.
y Do not allow children to operate the fixture.
y Use safety chain when fixing the unit. Handle the unit only by carrying its base instead
of head .
y The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces.
y Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.
y Before operating, ensure that the voltage and frequency of power supply matches the
power requirements of the unit.
y It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
y Don’t connect the device to any dimmer pack.
y During initial start-up, some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective, and it will decrease gradually
within 15 minutes.
y Make sure there are no flammable materials close to the unit while operating to avoid
fire hazard.
y Examine the power wires carefully; replace them immediately if there is any damage.
y Unit’s surface temperature may reach up to 85℃. Don’t touch the housing bare-handed
during its operation, and allow about 15 minutes for cooling the unit down before
Please read carefully the instruction manual which includes
important information about the installation usage and maintenance.
Moving Beamer BEAM-1800
4-
replacing bulb or maintenance as it could be very hot.
y Avoid any inflammable liquids, water or metal objects entering the unit. Once it
happens, cut off the mains power immediately.
y Do not operate in dirty or dusty environment; do clean the fixture regularly.
y Do not touch any wire during operation as there might be a hazard of electric shock.
y Avoid power wires and other cables twisted.
y The minimum distance between light output and the illuminated surface must be more
than 2.5 meters.
y Disconnect mains power before fuse/lamp replacement or servicing.
y Replace fuse/lamp only with the same type.
y In the event of serious operating problem, stop using the unit immediately.
y Never turn on and off the unit time after time.
y The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
y Do not open the unit as there are no user serviceable parts inside.
y Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead
to damage or malfunction. Please contact the nearest authorized technical assistance
center if needed.
y Disconnect the mains power if the fixture has not been used for a long time.
y Do use the original packing materials before transporting it once again.
Caution
y To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
y Hot lamp explosion hazard. Do not open the unit within 15 minutes after switching off.
y Do replace the bulb once it is damaged, deformed or life-expired.
y Do not look directly at the light while the bulb is on.
y Never touch bulb with bare fingers, as it is very hot after using.
y Do not start on the unit without bulb enclosure or when housing is damaged.
WARNING!
Maximum ambient temperature TA: 40℃. Don’t operate it when the
temperature is higher.
Moving Beamer BEAM-1800
5-
Product Items
y Moving Beamer BEAM-1800
y User manual
y 2 x Omega clamps
y 8GB memory SD card (packaged with user manual)
2. Installation
1. Bolt each clamp (1) to the Omega holder with screw and lock nut through the hole in the
holder.
2. Fasten the omega holders (2) on the bottom of the base by inserting quick-lock
fasteners (3) into the holes of the base and tighten fully clockwise.
3. Hang the fixture to the support (4) through clamp and fasten the screws (5). Fasten the
safety cable (6) through the bottom of the base and over the support.
90
°
1
2
3
4
6
5
Fig.1 Fig.2
4. Please refer to the diagram to know how to install the fixture in correct position.
Moving Beamer BEAM-1800
6-
Fig.3
Attention:
y Always ensure that the structure to which you are attaching the unit is secure and is
able to support a weight of 10 times of the unit’s weight.
y Also always use a safety cable that can hold 12 times of the weight of the unit when
installing the fixture.
y Make absolute sure that the unit is firmly fixed in a way that no vibrating or slipping
would occur during operation.
y The equipment must be installed beyond the areas where persons may walk by or be
seated.
y The rigging has to be operated by a skilled person.
Moving Beamer BEAM-1800
7-
3. Technical Specification
Power supply
- AC 120V~240V 50/60Hz
Power Consumption
- 250W at 230V 50Hz
- 260W at 120V 60Hz
Fuse
- T 5A
Projector
- Display technology: DLP by Texas Instruments
- Lamp: Osram E20.8 180W Lamp
- Lamp life time: 1,000 hrs (In the moving head)
- Beam angle: 24 degree
- Brightness(ANSI Lumens): 2500
- Contrast Ratio (Full on/ Full off): 1800:1 (typical)
- Resolution: SVGA 800 x 600
- Built-in Image size: 720 x 480
Wireless control
- Wirelessly controlled by W-DMX (option).
- Each W-DMX is sending out 512 channels of DMX.
- License free band of 2.45 GHz
Movement
- Pan: 540°
- Tilt: 270°
- Pan/Tilt moving speed adjustable.
- Automatic Pan/Tilt position correction.
- Built-in Pan/Tilt macro effects
- Easy calibration and maintenance by magnetic home positioning.
- Pan/Tilt position lock for transporting protection.
Image/ Video inputs:
- Data projector: 1x15-pin VGA port, 1xS-V ideo (NTSC or PAL) port, 1xComposite (CVBS)
port
- Supported image file types: JPG (Image resolution is 720 x 480px)
Moving Beamer BEAM-1800
8-
- Supported video file types: AVI, MJPEG
(From SD card: video resolution is 720 x 480)
(From computer: video resolution is 800 x 600 )
Shutter
- Blackout
Cool
- Fan cooled
Protocols
- DMX 512
- Date input/output: 3/5 Pin XLR socket
Memory card
- Memory card slot, hot swappable, max. 32 GB (Built in 8GB)
Weight
- 17.5kgs
Dimension
- 550 × 296 × 518 mm
Moving Beamer BEAM-1800
9-
DMX Channels
Mode
Channel
Mode 1
54-CH
Mode 2
29-CH
1 Pan Pan
2 Pan Fine Pan Fine
3 Tilt Tilt
4 Tilt Fine Tilt Fine
5 Pan/Tilt Speed Pan/Tilt Speed
6 Pan/Tilt Macro Shutter
7 Shutter Picture/Video
8 Picture/Video Video Number
9 Video Number Video Speed
10 Video Speed Layer1 Picture Directory /Color
11 Red Layer1 Picture Number/Preset Color
12 Green Layer2 Picture Directory
13 Blue Layer2 Picture Number
14 Layer1 Picture Directory /Color Layer3 Picture Directory/Filter Picture
15
Layer1 Picture Number/Preset
Color
Layer3 Picture Number
16 Layer1 Center Offset Picture Macro
17 Layer1 Center Rotation Picture Macro Center Offset
18 Layer1 X Zoom Picture Macro Center Rotation
19 Layer1 Y Zoom Picture Macro X Zoom
20 Layer1 Zoom Macro Picture Macro Y Zoom
21 Layer1 Rotation Picture Macro Zoom Macro
22 Layer2 Picture Directory Picture Macro Rotation
23 Layer2 Picture Number Focus
24 Layer2 Center Offset Color mode
25 Layer2 Center Rotation Screen Format
26 Layer2 X Zoom Mirror
27 Layer2 Y Zoom Keystone
28 Layer2 Zoom Macro Source
29 Layer2 Rotation Special Function
30
Layer3 Picture Directory/Filter
Picture
31 Layer3 Picture Number
Moving Beamer BEAM-1800
10-
32 Layer3 Center Offset
33 Layer3 Center Rotation
34 Layer3 X Zoom
35 Layer3 Y Zoom
36 Layer3 Zoom Macro
37 Layer3 Rotation
38 Picture Macro
39 Picture Macro Center Offset
40 Picture Macro Center Rotation
41 Picture Macro X Zoom
42 Picture Macro Y Zoom
43 Picture Macro Zoom Macro
44 Picture Macro Rotation
45 Focus
46 Color mode
47 Screen Format
48 Mirror
49 Keystone
50 Brightness
51 Contrast
52 Freeze
53 Source
54 Special Function
Moving Beamer BEAM-1800
11-
4. Description
4.1 Description of the fixture
For transportation protection, please set the tilt lock/unlock (2) and the pan lock/unlock
lever (3) in the lock position before any transportations. To unlock the head, move the tilt
lock/unlock (2) and the pan lock/unlock lever (3) to unlock position.
Caution: The head and arm must be unlocked before operation!
1. Head
2. Tilt lock
3. Pan lock
4. Front panel
5. Memory card slot
6. Arm
7. Handle
8. Back panel
Moving Beamer BEAM-1800
12-
4.2 Control Panel
Front View Rear View
○
1 LCD Display: shows the various menus and the selected functions.
○
2 LED
POWER On Power on
DMX On DMX input present
○
3 Antenna
W-DMX wireless receiver receive signal from a wide range.
○
4 Button
MENU
Used to select the different menu items
UP
To go up in the menu and to increase the values shown on the display
DOWN
To go back in the menu and to lower the values shown on the display
ENTER
Used to confirm your choice.
○
5 DMX input/output sockets:
For DMX 512 operation, use 3/5-pin XLR plug cable to link the units together
○
6 Video input sockets:
Composite video in (CVBS): (the length limit to 3 meters in normal operation.)
S-Video in (NTSC or PAL): (the length limit to 3 meters in normal operation.)
15-pin VGA in: (the length limit to 10 meters in normal operation.)
○
7 Power Switch:
Turns On/Off the power
5
6 7
8
9
1
2
3
4
Moving Beamer BEAM-1800
13-
○
8 Power Cable:
To connect to the mains AC outlet
○
9 Fuse (T 5 A):
Protect the unit from damage of over current.
5. Lamp
Osram E20.8 180W Lamp
y Because of its high internal pressure, there might be a risk that the discharge
lamp would explode during operation. The lamp emit s intense UV r adiation whic h
is harmful to the eyes and skin. The high luminance of the arc can cause sev ere
damage to the retina if you take a close look at the lamp.
y To protect the lamp, always turn off the lamp first (via control panel or DMX
controller) and let the unit’s fan run at least five minutes to cool down before
switching off the mains supply. Never handle the lamp or luminarie when it is hot.
y Do not touch the bulb with bare hands. If this happens, clean the lamp with
denatured alcohol and wipe it with a lint free cloth before installation.
y The lamp generates UV radiation. Never operate the lamp without appropriate
shielding.
y When lighting up, the lamp operates at high pressure and there is a slight risk of arc
tube rupture. The risk increases with age, temperature and improper handling of the
lamp. Do not use the lamp longer than its lifespan.
y Make sure the lamp is located in the right position of the unit for the best projection.
Loading...