Imex LX55 Multi
Imex LX55 Multi----line laser
Imex LX55 MultiImex LX55 Multi
line laser
line laserline laser
Imex LX55 & LX55D
Imex LX55 & LX55D
Imex LX55 & LX55DImex LX55 & LX55D
Congratulations on your purchase of a quality Imex self levelling
(pendulum) line laser.
These lasers have been designed for the professional and incorporate the
latest laser technology.
This highly versatile tool can be set up on the floor, elevating tripod or on a
wall bracket.
The following operating manual has been designed to assist in getting the
optimum performance from your instrument. Please read carefully before
using the instrument, and observe all safety conditions.
1. About the Instrument
1. About the Instrument ---- Functions
1. About the Instrument 1. About the Instrument
1.1 Instrument Overview
1.1 Instrument Overview
1.1 Instrument Overview1.1 Instrument Overview
Control panel Vertical beam windows
Functions
Functions Functions
On/off switch
Batteries
Fine adjustment
Horizontal beam
windows
screw
1.2 Control Panel
1.2 Control Panel
1.2 Control Panel1.2 Control Panel
Level vial
Outdoor mode button
(activates pulse mode)
Horizontal beam
button (activates
horizontal beams)
Vertical beam button
(activates vertical beam)
1.
1.3 Detector (LX55 only)
3 Detector (LX55 only)
1.1.
3 Detector (LX55 only)3 Detector (LX55 only)
Level vial Laser receptor band
Staff bracket
Level indication
Lights
Audible buzzer
Tripodic base
2. Basic Operation
2. Basic Operation
2. Basic Operation2. Basic Operation
1. Turn on:
Turn on: Turn on using the on/off switch. This releases the pendulum from its
Turn on:Turn on:
lock position, activates 1 horizontal beam and allows all beams to be turned on
using the buttons on the control panel.
2. Horizontal Beam:
Horizontal Beam: To turn on 360°horizontal laser line, press the horizontal
Horizontal Beam:Horizontal Beam:
button once.
Press the horizontal button once again to turn horizontal beam off.
3. Vertical Beams:
Vertical Beams: To turn on vertical beams press the vertical beam button, this
Vertical Beams:Vertical Beams:
activates 2 opposite vertical beams and the plumb spot.
Press the vertical button again to activate the remaining vertical beams, you now
have 4 vertical beams emitted at 90°to each other also forming a cross on the
ceiling. - Press vertical button again to turn vertical beams off.
4. Turn off:
Turn off: To turn off completely, switch the on/off switch to off position, this
Turn off:Turn off:
deactivates all beams and locks pendulum.
-The level vial is a guide only, unit will self level providing it’s within 3º of level.-
3. Outdoor Use
3. Outdoor Use LX55D
3. Outdoor Use3. Outdoor Use
For greater versatility this tool has a pulse mode which enables the tool to be
used in conjunction with a detector (LX55D) extending the tools range to 50m.
-To enable outdoor mode, turn instrument laser beam on then press the outdoor
mode switch once. This enables the beam pulsate mode so it can be picked up
by the detector.
-Turn on detector (on/off switch) You can now check level and 90º set-outs
outdoors using optional detector
-Press the outdoor mode button once again to disable outdoor mode
LX55D
LX55D LX55D
(with detector)
(with detector)
(with detector)(with detector)
4444. Calibration and Level Checking
. Calibration and Level Checking
. Calibration and Level Checking. Calibration and Level Checking
The accuracy of the tool is +/- 1.5mm in 10m.
Before use check that the instrument is within tolerance.
-Place instrument on a solid base i.e. bench top, approx 5m from a wall.
-Turn on horizontal beam and all vertical beams
-To check horizontal beam, point crossline towards wall & mark the wall
at horizontal level point
-Rotate instrument 90º(next crossline intersection) on tripodic base and
mark wall again, repeat this procedure at the remaining two crossline
intersections
-You should now have four marks on the wall. If these points are less than
1.5mm apart the instrument is ok to use if difference exceeds 1.5mm
send back to dealer for calibration.
To check vertical accuracy, utilise a known plumb point such as a doorway/
window frame and check that vertical beam lines up.
5555. Transportation and Storage
. Transportation and Storage
. Transportation and Storage. Transportation and Storage
The laser must be stored in a cool dry environment, free of dust and moisture.
On the completion of use the main On/Off switch must be switched to the off
position for transportation.
6666. Warranty
. Warranty
. Warranty. Warranty
The Imex LX55 and LX55D are covered by a 2 year warranty as detailed on the
warranty form. Fill out form and return to supplier.
7777. Accessories
. Accessories
. Accessories. Accessories
The LX55 can be used with a number of accessories, these include;
-Elevating tripod -Wall mount bracket
-Floor–ceiling laser pole -Levelling staff & more
8. Specifications
8. Specifications
8. Specifications8. Specifications
Copyright © International Measuring Equipment 2010
Free call 1800 669 110
Loading...