IMC Networks SP50 User Manual

McBasic

TP/FO & TP/BNC

Operation Manual

FCC Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which the user will be required to correct the interference at his own expense.

Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class B

limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B

prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.

Warranty

IMC Networks warrants to the original end-user purchaser that this product, EXCLUSIVE OF SOFTWARE, shall be free
from defects in materials and workmanship under normal and proper use in accordance with IMC Networks' instructions
and directions for a period of six (6) years after the original date of purchase. This warranty is subject to the limitations set
forth below.

At its option, IMC Networks will repair or replace at no charge the product which proves to be defective within such
warranty period. This limited warranty shall not apply if the IMC Networks product has been damaged by unreasonable
use, accident, negligence, service or modification by anyone other than an authorized IMC Networks Service Technician
or by any other causes unrelated to defective materials or workmanship. Any replaced or repaired products or parts carry
a ninety (90) day warranty or the remainder of the initial warranty period, whichever is longer.

To receive in-warranty service, the defective product must be received at IMC Networks no later than the end of the
warranty period. The product must be accompanied by proof of purchase, satisfactory to IMC Networks, denoting
product serial number and purchase date, a written description of the defect and a Return Merchandise Authorization
(RMA) number issued by IMC Networks. No products will be accepted by IMC Networks which do not have an RMA
number. For an RMA number, contact IMC Networks at PHONE: [phone] (in the U.S and Canada) or (949) 465­3000 or FAX: [phone]. The end-user shall return the defective product to IMC Networks, freight, customs and
handling charges prepaid. End-user agrees to accept all liability for loss of or damages to the returned product during
shipment. IMC Networks shall repair or replace the returned product, at its option, and return the repaired or new
product to the end-user, freight prepaid, via method to be determined by IMC Networks. IMC Networks shall not be
liable for any costs of procurement of substitute goods, loss of profits, or any incidental, consequential, and/or special
damages of any kind resulting from a breach of any applicable express or implied warranty, breach of any obligation
arising from breach of warranty, or otherwise with respect to the manufacture and sale of any IMC Networks product,
whether or not IMC Networks has been advised of the possibility of such loss or damage.

EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, IMC NETWORKS MAKES NO OTHER WARRANTIES,
WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS IMC NETWORKS PRODUCT, INCLUDING WITHOUT
LIMITATION ANY SOFTWARE ASSOCIATED OR INCLUDED. IMC NETWORKS SHALL DISREGARD AND NOT BE
BOUND BY ANY REPRESENTATIONS OR WARRANTIES MADE BY ANY OTHER PERSON, INCLUDING EMPLOYEES,
DISTRIBUTORS, RESELLERS OR DEALERS OF IMC NETWORKS, WHICH ARE

INCONSISTENT WITH THE WARRANTY SET FORTH ABOVE. ALL IMPLIED WARRANTIES INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY LIMITED TO THE DURATION OF THE
EXPRESS WARRANTY STATED ABOVE.

Every reasonable effort has been made to ensure that IMC Networks product manuals and promotional materials
accurately describe IMC Networks product specifications and capabilities at the time of publication. However, because of
ongoing improvements and updating of IMC Networks products, IMC Networks cannot guarantee the accuracy of printed
materials after the date of publication and disclaims liability for changes, errors or omissions.

ii

Table of Contents

FCC Radio Frequency Interference Statement ....................................................ii

Warranty............................................................................................................ii

About the McBasic.............................................................................................1

Installing the McBasic.........................................................................................1

Configuring McBasic ..........................................................................................1

Twisted Pair Crossover/Straight-Through Switch..................................................1

BNC Port Termination........................................................................................2

LinkLoss and Pulsing FiberAlert ..........................................................................2

LED Operation...................................................................................................5

Installation Troubleshooting ...............................................................................7

Specifications .....................................................................................................8

Fiber Optic Cleaning Guidelines.......................................................................10

Electrostatic Discharge Precautions...................................................................10

Safety Certifications..........................................................................................11

iii

Notes

iv

About the McBasic

The McBasic series consists of low-cost, IEEE 802.3 single-conversion, 1U high,
standalone media converters. The McBasic TP/FO converts 10Base-T twisted pair to
10Base-FL multi-mode or single-mode fiber and includes one RJ-45 connector and
one pair of ST or SC connectors.

McBasic TP/BNC converts 10Base-T twisted pair to 10Base-2 thin coax and includes
one RJ-45 connector and one BNC connector. Each McBasic includes diagnostic
LEDs and an internal 100/240 VAC power supply.

Installing the McBasic

McBasic comes ready to install; configure after installation. To install McBasic, first
make sure that the unit is placed on a suitable flat surface.

Attach the cables between the McBasic and each device that will be interconnected,
then plug the unit into a reliable, filtered power source.

NOTE

The McBasic TP/FO does not auto-negotiate, therefore IMC Networks does NOT
recommend connecting it to a switch, media converter or other device that ONLY
auto-negotiates; connect to a device that is 10 Mbps or to a device that you can
force to 10 Mbps.

Configuring McBasic

Once installed, configure McBasic TP/FO for the following:

A crossover or pass-through connection for the twisted pair port

•
Pulsing FiberAlert

•

Once installed, configure McBasic TP/BNC for the following:

•

A crossover or pass-through connection for the twisted pair port
BNC port termination (default = Enabled)

•

Twisted Pair Crossover/Straight-Through Switch

The twisted pair port on McBasic TP/FO and McBasic TP/BNC features a pushbutton
switch, located next to the twisted pair connector, for selecting a crossover
workstation connection or straight-through repeater/hub connection.

Select a straight-through connection by pressing the push-button IN. A crossover
connection is selected when the push-button is OUT. If uncertain whether a
crossover or straight-through connection is needed, set the push-button to the
position that makes the TP LNK (link) LED glow.

1