Page 1
IE-iMcV-VDSL2-LANextender
Operation Manual
Page 2
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which the user will be required to correct the interference at their expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class B
limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B
prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.
Warranty
IMC Networks warrants to the original end-user purchaser that this product, EXCLUSIVE OF SOFTWARE, shall be free
from defects in materials and workmanship under normal and proper use in accordance with IMC Networks' instructions
and directions for a period of six (6) years after the original date of purchase. This warranty is subject to the limitations set
forth below.
At its option, IMC Networks will repair or replace at no charge the product which proves to be defective within such
warranty period. This limited warranty shall not apply if the IMC Networks product has been damaged by unreasonable
use, accident, negligence, service or modification by anyone other than an authorized IMC Networks Service Technician
or by any other causes unrelated to defective materials or workmanship. Any replaced or repaired products or parts carry
a ninety (90) day warranty or the remainder of the initial warranty period, whichever is longer.
To receive in-warranty service, the defective product must be received at IMC Networks no later than the end of the
warranty period. The product must be accompanied by proof of purchase, satisfactory to IMC Networks, denoting
product serial number and purchase date, a written description of the defect and a Return Merchandise Authorization
(RMA) number issued by IMC Networks. No products will be accepted by IMC Networks which do not have an RMA
number. For an RMA number, contact IMC Networks at PHONE: (800) 624-1070 (in the U.S and Canada) or (949) 4653000 or FAX: (949) 465-3020. The end-user shall return the defective product to IMC Networks, freight, customs and
handling charges prepaid. End-user agrees to accept all liability for loss of or damages to the returned product during
shipment. IMC Networks shall repair or replace the returned product, at its option, and return the repaired or new
product to the end-user, freight prepaid, via method to be determined by IMC Networks. IMC Networks shall not be
liable for any costs of procurement of substitute goods, loss of profits, or any incidental, consequential, and/or special
damages of any kind resulting from a breach of any applicable express or implied warranty, breach of any obligation
arising from breach of warranty, or otherwise with respect to the manufacture and sale of any IMC Networks product,
whether or not IMC Networks has been advised of the possibility of such loss or damage.
EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, IMC NETWORKS MAKES NO OTHER WARRANTIES,
WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS IMC NETWORKS PRODUCT, INCLUDING WITHOUT
LIMITATION ANY SOFTWARE ASSOCIATED OR INCLUDED. IMC NETWORKS SHALL DISREGARD AND NOT BE
BOUND BY ANY REPRESENTATIONS OR WARRANTIES MADE BY ANY OTHER PERSON, INCLUDING EMPLOYEES,
DISTRIBUTORS, RESELLERS OR DEALERS OF IMC NETWORKS, WHICH ARE
INCONSISTENT WITH THE WARRANTY SET FORTH ABOVE. ALL IMPLIED WARRANTIES INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY LIMITED TO THE DURATION OF THE
EXPRESS WARRANTY STATED ABOVE.
Every reasonable effort has been made to ensure that IMC Networks product manuals and promotional materials
accurately describe IMC Networks product specifications and capabilities at the time of publication. However, because of
ongoing improvements and updating of IMC Networks products, IMC Networks cannot guarantee the accuracy of printed
materials after the date of publication and disclaims liability for changes, errors or omissions.
ii
Page 3
Table of Contents
FCC Radio Frequency Interference Statement ........................................................... ii
Warranty................................................................................................................... ii
About the IE-iMcV-VDSL2-LANextender ...................................................................1
Configuration Instructions ......................................................................................... 1
Installing IE-iMcV-VDSL2-LANextender Modules.......................................................2
LED Operation.......................................................................................................... 3
DIP Switch Settings ...................................................................................................4
Host (CO) Module Configuration ..............................................................................5
Remote (CPE) Module Configuration.........................................................................5
DATA Port Features ..................................................................................................5
Auto Negotiation.......................................................................................................5
Selective Advertising .................................................................................................6
SNMP Management ..................................................................................................6
LINK Quality .............................................................................................................7
Forcing Duplex Mode ...............................................................................................7
Forcing the Data Port Speed...................................................................................... 7
Flow Control .............................................................................................................7
Link Fault Pass-Through ............................................................................................8
Fault Loopback (FL)...................................................................................................8
Maximum Bandwidth IE-iMcV-VDSL2-LANextender Link LEDS ................................9
Primary Line Protector ........................................................................................11
Appendix—Pinouts .................................................................................................12
RJ-45 Data Port Pinout (MDI) ..............................................................................12
RJ-11 Port Pinout ................................................................................................12
Troubleshooting ......................................................................................................13
Specifications .......................................................................................................... 14
IMC Networks Technical Support............................................................................15
Safety Certifications.................................................................................................16
iii
Page 4
About the IE-iMcV-VDSL2-LANextender
The IE-iMcV-VDSL2-LANextender enables LAN and Campus network managers, and
service providers, to use an existing phone-grade wiring to support high bandwidth
Ethernet connections. Industry standard 2Base-TL provisions symmetric data delivery
over the outside plant defined by IEEE802.3ah. 10Pass-TS transport is designed to
meet short-range, high data rate requirements over standard copper wire defined by
IEEE802.3ah for inside a plant environment. They can achieve this by using Ethernet
over VDSL where the 100m distance limitation of twisted pair data cabling is no
longer a challenge.
Designed with VDSL (second generation Very high-bit-rate Digital Subscriber Line)
technology, the IMC Networks Ethernet-to-VDSL converter allows the transmission of
data over a single pair of sub-standard CAT3 and other telephone cabling to achieve
substantially longer distances. As a media and protocol converter, the IE-iMcVVDSL2-LANextender includes the ability to transfer data both symmetrically and
asymmetrically to meet the customer's needs. In either mode, the VDSL2 port
automatically adjusts to an operating point that maximizes the Full-Duplex bandwidth
capability of the line for true plug-and-play operation.
Two IE-iMcV-VDSL2-LANextender media converters are configured as pairs for each
link. One is configured as a Host (Central Office (CO)) IE-iMcV-VDSL2-LANextender
module and is typically deployed at the CO close to network management systems.
The other is configured as a Remote Customer Premise (CPE) IE-iMcV-VDSL2LANextender module and is deployed at the CPE. Full CNMP remote line
management is provided through an IMC Networks managed chassis, providing
remote notification of all line fault conditions.
IE-iMcV-VDSL2-LANextender modules include:
• One VDSL port with an RJ-11 connector (VDSL)
• One 10/100BaseT Ethernet port with an RJ45 connector (DATA Port)
Configuration Instructions
IE-iMcV-VDSL2-LANextender modules include various user-configurable features.
These features are selectable by using DIP Switches and software. The following
sections describe the DIP Switches for the Host (CO) and Remote (CPE) module
configuration.
1
Page 5
Installing IE-iMcV-VDSL2-LANextender Modules
If the VDSL line is connected to the outside plant, the wire entry point to the building
must have primary line protectors installed (Bourns 2377-45 Series DigiGard or
equivalent, illustrated in the Primary Line Protector section).
Before installing an IE-iMcV-VDSL2-LANextender module, set the options using the
DIP Switches (refer to the DIP Switch Settings section for more information).
Install IE-iMcV-VDSL2-LANextender modules in any IMC Networks iMediaChassis
series or a MediaChassis series. Each module requires one slot in the chassis; always
use IE-iMcV-VDSL2-LANextender modules in pairs with the Host module at the CO
and the Remote module at the CPE.
To install a module, remove the blank brackets (if present) covering the slots where
you will install the module by removing the screws on the outside edges of the
bracket. Slide the module into the chassis, via the card guides, until the module is
seated securely in the connector. Secure the module to the chassis by tightening the
captive screw. Save any blanks removed during installation for future use.
Remote (CPE) modules can be installed in a managed or unmanaged chassis. Remote
(CPE) modules can only be managed from the connected Host (CO)
IE-iMcV-VDSL2-LANextender module installed in a managed chassis. The user
should always set remote DIP Switches to provide a base value under VDSL line fault
conditions. In addition, some features may not be software configurable on the
remote unit. After setting the DIP Switches, install the IE-iMcV-VDSL2-LANextender
module. Once the VDSL line is established the line can be monitored and
2
configured through the iView
www.imcnetworks.com
.
management software available for download at
2
Page 6
LED Operation
LED Function (VDSL)
RAI
FL
LOS
ER
8-4-2-1
The Remote Alarm Indication led is
the far end of the Unit has an alarm
Fault Loopback will be ON
and BLINK if it is actively inhibiting the Ethernet port due to a
LOS of the VDSL line
The LOS led is
The ERROR led will Blink
receives a symbol error. ON if the VDSL bandwidth falls below
the user defined level.
These 4 GREEN LEDs form a binary code indicating the MAX
bandwidth the VDSL line can support as described in
Maximum Bandwidth IE-iMcV-VDSL2-LANextender Link LEDs.
Blinks slow GREEN at power up.
Blinks fast GREEN when line connection has been established.
RED
when the VDSL port is down.
LINK Quality
GREEN
YELLOW
YELLOW
if this function is enabled
when the unit at
when the VDSL line
if this function is
OVF
LFPT
LOS
ER
Glows GREEN when VDSL is valid and working.
LED Function (DATA)
Overflow LED will Blink
congestion on the VDSL line.
Link Fault Pass-Through will be ON
enabled and BLINK if it is actively inhibiting the Ethernet port
due to a LOS of the far end TX line.
The LOS led is
The ER led is
RED
YELLOW
YELLOW
when the TX port is down.
when the TX port receives an error.
when frames are lost due to
GREEN
The VDSL2 will generate a Trap (when enabled in iView2 ) whenever a Loss of Signal
(LOS) occurs. In addition, the end user can set a VDSL Quality Level that will
generate a Trap if the line fails below that set level.
3
Page 7
DIP Switch Settings
The DIP Switches allow the user to configure most of the module features before
installing the unit. These also enable the Host to Remote management channel used
with SNMP management. Refer to the following diagram and setting table for DIP
Switch selection information.
Switch # Feature Function Default
1 HOST HOST=OFF / Remote=ON OFF
2 LFPT On= Link Fault Pass Through Enabled OFF
3 FL ON= Fault Loopback Enabled OFF
4 Band Plan
5 AN On= Auto Negotiation ON ON
6 Flow Control On= Flow Control ON ON
7 Selective AN
8 Duplex OFF= Full Duplex / ON= Half Duplex OFF
9 Speed On= 100Mbps / Off= 10Mbps OFF
10 Test Factory Test: Do not Use OFF
On= Asymmetric 998 with ISDN
Off= Symmetric 997 with ISDN
On= Selectively advertises Speed Duplex if
AN is enabled
These features are described in more detail in the following sections.
OFF
OFF
4
Page 8
Host (CO) Module Configuration
To allow the HOST (CO) Control Office IE-iMcV-VDSL2-LANextender module to
manage the remotely connected CPE IE-iMcV-VDSL2-LANextender unit, set DIP
Switch #1 to the OFF position (default setting). This selection can only be performed
manually and cannot be overridden by software settings.
A Host configured CO IE-iMcV-VDSL2-LANextender module must be installed in a
managed chassis to allow SNMP management through iView
²
. The iMediaChassis
series, available in 3, 6 and 20 slots with an optional SNMP Management Module, is
recommended. Please refer to the section SNMP Management.
Remote (CPE) Module Configuration
To configure a CPE IE-iMcV-VDSL2-LANextender module as a Remote CPE, set DIP
Switch #1 to the ON position (OFF is the default setting).
A Remote CPE configured IE-iMcV-VDSL2-LANextender module can be installed in
an unmanaged chassis. These chassis can include the IE-MediaChassis series chassis,
the MediaChassis series chassis, the iMediaChassis series chassis with the optional
SNMP agent management module removed.
DATA Port Features
The 10/100BaseT DATA port on the IE-iMcV-VDSL2-LANextender Auto Negotiates
for speed and duplex mode. These modules also provide the option of manually
setting the speed and duplex mode if the connected devices do not have the ability
to Auto Negotiate, or when Auto-Negotiation is not desired by configuring using DIP
Switches #8 and #9.
Auto Negotiation
The IE-iMcV-VDSL2-LANextender ships from the factory with Auto Negotiation
enabled on the DATA port. In this mode, the DATA port negotiates for speed and
duplex (i.e. the module detects 10 Mbps Full-Duplex, 10 Mbps Half-Duplex, 100
Mbps Full-Duplex or 100 Mbps Half-Duplex with Flow Control). Configure AutoNegotiation on an IE-iMcV-VDSL2-LANextender by adjusting the DIP Switch #5 (for
unmanaged modules) or via the management software (for managed modules).
5
Page 9
Selective Advertising
Selective Advertising (DIP Switch #7) when used in combination with Auto
Negotiation, advertises only the configured speed and duplex mode for the DATA
port. If Selective Advertising and Auto Negotiation are both switched ON, the DATA
port’s speed (10 or 100 Mbps) and Duplex mode (FDX or HDX) are selectively
advertised individually per switch setting 5 and 7.
NOTE
If you require a specific speed and/or duplex mode, IMC Networks recommends using
Selective Advertising rather than Force Mode when connecting the modules to devices that
can ONLY Auto Negotiate. Selective Advertising is NOT an option when you disable Auto
Negotiation.
SNMP Management
Once the DIP Switches have been set on each module to enable one to be a Host
and the other a Remote, the Host can be installed in an iMediaChassis that includes
an installed SNMP Management Module. The Host VDSL2 module then manages
2
the Remote VDSL2 module via the SNMP software iView
.
2
Traps can also be set in the iView
software. A Trap will be generated on any Loss of
Signal (LOS); but more importantly, the end user can set a VDSL
will generate a trap if the line fails below the assigned level.
Quality Level
that
6
Page 10
LINK Quality
Link Quality is defined by 4 values: 8,4,2,1. The four green LEDs form a
binary
code
indicating the MAX bandwidth the VDSL line can support. The appropriate LED will
light once the line quality is dynamically detected. This represents the maximum
Downstream data rate (Kbps) the line can support based upon line noise and line
length. The Upstream rate will be less based on the Base Plan used.
Forcing Duplex Mode
The DATA port can be manually configured on the IE-iMcV-VDSL2-LANextender
module for Half- or Full-Duplex operation. Before manually setting the duplex
mode, disable Auto Negotiation (Set DIP Switch #5 to OFF).
• Full-Duplex for the DATA port is configured by setting DIP Switch #8 to the OFF
position (default).
• Half-Duplex for the DATA port is configured by setting DIP Switch #8 to the ON
position.
Forcing the Data Port Speed
The DATA port can be manually configured on IE-iMcV-VDSL2-LANextender module
for 10 Mbps or 100 Mbps operation. Before manually setting the speed, disable Auto
Negotiation (Set DIP Switch #5 to the OFF position.)
• 10 Mbps for the DATA port is configured by setting DIP Switch #9 to the OFF
position (default).
• Configure the DATA port for 100 Mbps operation by setting DIP Switch #9 to
the ON position.
Flow Control
Flow Control is used as back pressure on the 10/100BaseT DATA interface to avoid
dropping packets during VDSL link congestion. Full-Duplex Flow Control will be
advertised only when the module is set to Full-Duplex Mode. For Full-Duplex Flow
Control to operate, the link partner (connected devices) must also support Flow
Control. Half-Duplex Flow Control does not advertise but provides a hardware based
backpressure on the Ethernet line to limit traffic.
Flow control should be considered whenever the VDSL line provides less bandwidth
than the DATA port. If the Ethernet line is attempting to send more data than the
VDSL2 line can support, the Overflow (OVF) LED will come ON indicating frames are
being discarded due to congestion.
7
Page 11
Overflow activity will be less if Flow Control is enabled. Flow Control or Pause will
limit the number of dropped Ethernet frames by reducing the congestion, therefore
minimizing the overflow of the VDSL line.
Configure the DATA port on IE-iMcV-VDSL2-LANextender module for Flow Control
by setting DIP Switch #6 to the ON position.
Link Fault Pass-Through
LNK
LNK
LNK
FL
TX
LFPT
B
TIP
VDSL2
RING
RAI
When a 10/100BaseT port is lost, the unit sends a fault signal (RAI) to the VDSL line.
If the LFPT function is enabled at the Far End VDSL port receiving this fault
indication, the far end unit will drop the link on the 10/100BaseT port and Blink the
LFPT LED. This function must be enabled at both ends of the VDSL line for this to
function in both directions. The LFPT function is only active in one direction at a
time and is indicated by the flashing LED. As such, clearing the far end fault may
uncover a fault at the local end.
TIP
VDSL2
RING
LNK
RAI
LFPT
FL
LNK
TX
LNK
Fault Loopback (FL)
LNK
LNK
B
LNK
FL
TX
LFPT
TIP
VDSL2
RING
RAI
TIP
VDSL2
RING
LNK
RAI
LFPT
B
FL
LNK
TX
LNK
The Fault Loopback (FL) function will force the 10/100BaseT port to drop link if the
VDSL line has lost link. If FL is enabled the LED will be ON GREEN and if this
function is actively inhibiting the Ethernet port this LED will Blink.
8
Page 12
Maximum Bandwidth IE-iMcV-VDSL2-LANextender Link LEDS
The standard single pair IE-iMcV-VDSL2-LANextender unit will provide the following
Rate/Reach performance under the best conditions and still maintain a BER > 10^-9
performance over single pair 24 AWG (0.5mm) twisted wire.
IE-iMcV-VDSL2-LANextender Rate/Reach
Distance Link Link Link Link BW 997 BW 998
(feet) 8 4 2 1
<Mbps
(down)
<Mbps
(up)
<Mbps
(down)
<Mbps
(up)
<950 1 1 1 1 93 76 99 50
950 1 1 1 1 74 64 90 45
1200 1 1 0 1 64 56 81 39
1500 1 0 1 1 52 47 70 30
1800 1 0 0 1 43 35 59 22
2300 0 1 1 1 33 20 45 12
3200 0 1 0 1 24 9 29 5
4700 0 0 1 1 17 1 18 1
5500 0 0 0 1 11 1 11 1
>5500 0 0 0 0 no Link no Link no Link no Link
9
Page 13
The unit will automatically adjust to reach the best bandwidth performance for the
physical line it is connected to. The associated LED display will indicate the
Bandwidth performance the unit is running at any given time.
bandwidth that is being transmitted but the bandwidth the line is capable of.
This is not the
The
Bandwidth number is based on "User Payload" and does not include the Ethernet
Frame overhead. For Band Plan 998, this LED display will indicate the MAX down
stream rate to the remote unit.
Band Plan 997 will provide the greatest symmetrical bandwidth the line can support.
The end user can also select Band Plan 998 for asymmetric operation to provide
better downstream performance. Either plan will automatically adjust for the greatest
bandwidth transport. The IE-iMcV-VDSL2-LANextender will automatically seek the
best operating condition for the physical line it is connected to.
NOTE
The RANGE is only an approximation based on a typical line in a normal noise environment.
Actual distances will very depending on the condition of the physical line in use.
When the Ethernet port is connected at 10BaseT, the VDSL2 line will be limited to
10 Mbps operation and will indicate a RANGE of 5500 feet or less for all length lines.
10
Page 14
Primary Line Protector
NOTE
If VDSL line is connected to the outside plant, the wire entry point to the building
must have primary line protectors installed.
11
Page 15
Appendix—Pinouts
RJ-45 Data Port Pinout (MDI)
The following table lists the pin
configuration for the RJ-45 Data
connector.
Pin Signal
1 Transmit+
2 Transmit3 Receive+
4 No Connection
5 No Connection
6 Receive7 No Connection
8 No Connection
RJ-11 Port Pinout
VDSL ports are supported on RJ-11 (pin
3,4) connectors.
Pin Signal
1
2
3 Ring (VDSL)
4 TIP (VDSL)
5
Pin 1
Pin 1
12
Page 16
Troubleshooting
The most common failure of a VDSL line is its slow degradation over time due to
aging of the line or increased line noise as additional service is added to the same
Line bundle. To help detect this degradation over time, the unit provides a userdefined Minimum Quality Level. Once this level is reached, the unit will send an
SNMP TRAP indication for low line quality. This can be used to provide an advanced
notice to the customer of a potential problem BEFORE a loss of service is detected by
the customer.
13
Page 17
Specifications
Standards:
ITU-TG.993.1
ITU-TG.997.1
GR-1089-Core Secondary Line Protection
Power Consumption (Typical):
550 mA @ 5 V
Operating Temperature:
-40°F to +185°F (-40°C to +85°C)
Storage Temperature:
-13°C to +158°F (-25°C to +70°C)
Humidity:
5 to 90% (non-condensing); 0 to 10,000 ft. altitude
Dimensions:
Single-Slot iMcV Chassis-Mounted Module
14
Page 18
IMC Networks Technical Support
Tel:
(949) 465-3000 or (800) 624-1070 (in the U.S. and Canada);
+32-16-550880 (Europe)
Fax:
E-Mail:
Web:
(949) 465-3020
techsupport@imcnetworks.com
www.imcnetworks.com
15
Page 19
Certifications
CE: The products described herein comply with the Council Directive on
Electromagnetic Compatibility (2004/108/EC). For further details,
contact IMC Networks.
Class 1 Laser product, Luokan 1 Laserlaite,
Laser Klasse 1, Appareil A’Laser de Classe 1
European Directive 2002/96/EC (WEEE) requires that any equipment that bears this
symbol on product or packaging must not be disposed of with unsorted municipal
waste. This symbol indicates that the equipment should be disposed of separately
from regular household waste. It is the consumer’s responsibility to dispose of this
and all equipment so marked through designate80d collection facilities appointed by
government or local authorities. Following these steps through proper disposal and
recycling will help prevent potential negative consequences to the environment and
human health. For more detailed information about proper disposal, please contact
local authorities, waste disposal services, or the point of purchase for this equipment.
16
Page 20
19772 Pauling • Foothill Ranch, CA 92610-2611 USA
TEL: (949) 465-3000 • FAX: (949) 465-3020
www.imcnetworks.com
© 2012 IMC Networks. All rights reserved.
The information in this document is subject to change without notice. IMC Networks assumes no responsibility for any
errors that may appear in this document. IE-iMcV-VDSL2-LANextender is a trademark of IMC Networks. Other brands or
product names may be trademarks and are the property of their respective companies.
Document Number 51-80970-00 A2 April 2012
Page 21
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
B&B Electronics:
851-18200
Loading...